The primary objective of this study was to quantitatively analyze compressive static stress distributions across pallet deck surfaces supporting flexible and rigid packaging in simulated warehouse storage systems. Three different densities of polyolefin foams (2, 4, and 6 lb/ft3, pcf) simulated a variety of flexible and rigid packaging with a range of stiffness properties. A layer of single wall C-flute corrugated fiberboard acted as a sensing medium and also simulated the bottom of a corrugated box. Pressure sensitive films were used to detect compressive static stresses at the interface between the polyolefin foams and the pallet deckboard. Image analysis computer software program was developed to quantitatively characterize stress distributions left on pressure sensitive film. 280 lbs of compression load were applied to a Plexiglas® pallet section (40 x 3.5 inches, L x W) with ¾ inch deck thickness, as well as to a steel pallet section (40 x 3.5 inches, L x W) with ½ inch deck thickness. In both cases, the pallet sections were used in a simulated pallet storage rack. 700 lbs of compression load were applied to the same steel pallet section that was used in the racking simulation and the Plexiglas® pallet sections (40 x 3.5 inches, L x W) with ½ and ¾ inch deck thicknesses were used in simulated block (floor) stack storage to measure the stress distributions and deflections of deckboards. Applying the final models of resultant non-uniform stress distributions enabled the development of finite element analysis (FEA) models of pallet deckboard deflections. The predicted FEA models of the deckboard deflections were validated through comparison with experimentally measured deflections in the simulated warehouse storage systems. In the final models, the resultant three foams' stress distributions across pallet deck surfaces in both rack and floor stack storage simulations were non-uniform. The changes in the degree of stress concentrations and maximum stress levels along the deckboards varied, depending on the stiffness of the foams and deckboards and the support conditions in the simulated warehouse storage models. Qualified test indicates that the 2pcf and 4pcf foams represent non-rigid sack products and the 6pcf foam represents rigid packaging and contents. All tests were conducted within a few minutes; hence, all test data were assumed to be initially resulted compressive stresses. The compressive stresses may change over time. The measure of stress concentrations is the stress intensity factor, which is the ratio of initial maximum resultant compressive stress to the applied stress. The initial maximum resultant compressive stresses were adjusted for rate of loading which varied due to the difference in the stiffness of the foams. The table below shows the adjusted initial maximum resultant compressive stress intensity factors. The product of the calculation uniformly distributed compressive stress and the stress intensity factor is the appropriate criteria for designing packaging of product with adequate compressive strength. These factors will be useful when designing pallets, packaging, and unit loads.In simulated block stack storage, the foam stiffness (package and product stiffness) had a more significant effect on the stress distributions and concentrations along the deckboards than did the pallet deck stiffness. As a result, the stiffer foam presented a greater change in stress levels along the deckboard under the compression load. The quantified and evaluated stress concentrations and stress distributions will be useful in understanding the interactions between pallets and packaging, reducing product damage and improving the safety of the work place during the long-term storage of the unit loads. The predicted FEA models will allow the industry to better optimize pallets, packaging, and unit load designs. / Master of Science

In the last years, the number of freely available Linked and Open Data datasets has multiplied into tens of thousands. The numbers of applications taking advantage of it, however, have not. Thus, large portions of potentially valuable data remain unexploited and are inaccessible for lay users. Therefore the upfront investment in releasing data in the first place is hard to justify. The lack of applications needs to be addressed in order not to undermine efforts put into Linked and Open Data. In existing research, strong indicators can be found that the dearth of applications is due to a lack of pragmatic, working architectures supporting these applications and guiding developers. In this thesis, a new architecture for the integration and application of Linked and Open Data is presented. Fundamental design decisions are backed up by two studies: firstly, based on real-world Linked and Open Data samples, characteristic properties are identified. A key finding is the fact that large amounts of structured data display tabular structures, do not use clear licensing and involve multiple different file formats. Secondly, following on from that study, a comparison of storage choices in relevant query scenarios is made. It includes the de-facto standard storage choice in this domain, Triples Stores, as well as relational and NoSQL approaches. Results show significant performance deficiencies of some technologies in certain scenarios. Consequently, when integrating Linked and Open Data in scenarios with application-specific entities, the first choice of storage is relational databases. Combining these findings and related best practices of existing research, a prototype framework is implemented using Java 8 and Hibernate. As a proof-of-concept it is employed in an existing Linked and Open Data integration project. Thereby, it is shown that a best practice architectural component is introduced successfully, while development effort to implement specific program code can be simplified. Thus, the present work provides an important foundation for the development of semantic applications based on Linked and Open Data and potentially leads to a broader adoption of such applications.

This master thesis deals with improving of the storing in the Delta Electronics (Slovakia). Initially, an analysis of effectiveness of the current system was prepared. The main goal of this paper is to recognize the major drawback of the current system and propose a way to remove them and improve the overall storing system and goods expedition.

Diploma thesis named „The Study of Warehousing Processes in a Manufacturing Company“is aimed on the mapping of the warehousing processes and the current method of the storage in the manufacturing company. Goal of this thesis is identifying the potential, which should be the result of the realization of the created suggestions, based on the mapping and analyzing current situation of the warehousing processes and warehouse area.

No description available.