The work presented has the ultimate aim to increase dynamic mechanical properties by improvements in density and optimisation of microstructure of ultra high carbon PM steels by careful selection of processes, i.e. mixing, binding, alloying, heating profile and intelligent heat treatment. ThermoCalc modelling was employed to predict liquid phase amounts for two different powder grades, Astaloy 85Mo or Astaloy CrL with additive elements such as (0.4-0.6wt%)Si, (1.2-1.4wt%)C and (1-1.5wt%)Mn, in the sintering temperature range 1285-1300ºC and such powder mixes were pressed and liquid phase sintered. In high-C steels carbide networks form at the prior particle boundaries, leading to brittleness, unless the steel is heat-treated. To assist the breaking up of these continuous carbide networks, 0.4-0.6% silicon, in the form of silicon carbide, was added. The water gas shift reaction (C + H2O = CO + H2, start from ~500ºC) and Boudouard reaction (from ~500ºC complete ~930ºC) form CO gas in the early part of sintering and can lead to large porosity, which lowers mechanical properties. With the use of careful powder drying, low dew point atmospheres and optimisation of heating profiles, densities in excess of 7.70g/cm3 were attained. The brittle microstructure, containing carbide networks and free of cracks, is transformed by intelligent heat treatment to a tougher one of ferrite plus sub-micron spheroidised carbides. This gives the potential for production of components, which are both tough and suitable for sizing to improve dimensional tolerance. Yield strengths up to 410 MPa, fracture strengths up to 950 MPa and strains of up to 16 % were attained. Forging experiments were subsequently carried out for spheroidised specimens of Fe-0.85Mo+06Si+1.4C, for different strain rates of 10-3, 10-2, 10-1 and 1sec-1 and heated in argon to 700ºC, density ~7.8g/cm3 and 769 MPa yield strength were obtained.

Forging temperature is one of the basic considerations in forging processes. In warm forging, the metals are forged at temperatures about the recrystallization temperature and below the traditional hot forging temperature. Warm forging has many advantages when compared to hot and cold forging. Accuracy and surface finish of the parts is improved compared to hot forging while ductility is increased and forming loads are reduced when compared to cold forging. In this study, forging process of a part which is currently produced at the hot forging temperature range and which needs some improvements in accuracy, material usage and energy concepts, is analyzed. The forging process sequence design with a new preform design for the particular part is proposed in warm forging temperature range and the proposed process is simulated using Finite Element Method. In the simulations, coupled thermal mechanical analyses are performed and the dies are modeled as deformable bodies to execute die stress analysis. Experimental study is also carried out in METU-BILTIR Center Forging Research and Application Laboratory and it has been observed that numerical and experimental results are in good agreement. In the study, material wastage is reduced by proposing using of a square cross section billet instead of a circular one, energy saving and better accuracy in part dimensions is achieved by reducing the forging temperature from the hot forging to the warm forging temperature range.

Semi-hot or warm forging is an economical alternative to the conventional forging processes by combining advantages of hot and cold forging processes. In this study, a new forging process sequence and design of the preform die for a part which has been produced by hot forging are proposed to be produced by semi-hot forging. Thermo-mechanical finite element analyses are performed over the stages of forging process. The billet and the dies are modeled as elastic-plastic bodies. Effects of preform die geometry on the die stresses and the forging load are investigated using finite element method. Comparison of the results obtained by using two different commercial finite element analysis programs is done for semi-hot and hot forging temperature ranges. The forging temperatures are determined for the particular part and the experiments are conducted by using the 1000 ton forging press. The parts are produced without any defects and material wastage in the form of flash is reduced. The numerical results are also compared with the experimental results and a good agreement is achieved.

Forging is a metal forming process commonly used in industry. Forging process is strongly affected by the process temperature. In hot forging process, a wide range of materials can be used and even complex geometries can be formed. However in cold forging, only low carbon steels as ferrous material with simple geometries can be forged and high capacity forging machinery is required. Warm forging compromise the advantages and disadvantages of hot and cold forging processes. In warm forging process, a product having better tolerances can be produced compared to hot forging process and a large range of materials can be forged compared to cold forging process. In this study, forging of a particular part which is being produced by hot forging at 1200&deg / C for automotive industry and have been made of 1020 carbon steel, is analyzed by the finite volume analysis software for a temperature range of 850-1200&deg / C. Experimental study has been conducted for the same temperature range in a forging company. A good agreement for the results has been observed.

The work presented has the ultimate aim to increase dynamic mechanical properties by improvements in density and optimisation of microstructure of ultra high carbon PM steels by careful selection of processes, i.e. mixing, binding, alloying, heating profile and intelligent heat treatment. ThermoCalc modelling was employed to predict liquid phase amounts for two different powder grades, Astaloy 85Mo or Astaloy CrL with additive elements such as (0.4-0.6wt%)Si, (1.2-1.4wt%)C and (1-1.5wt%)Mn, in the sintering temperature range 1285-1300ºC and such powder mixes were pressed and liquid phase sintered. In high-C steels carbide networks form at the prior particle boundaries, leading to brittleness, unless the steel is heat-treated. To assist the breaking up of these continuous carbide networks, 0.4-0.6% silicon, in the form of silicon carbide, was added. The water gas shift reaction (C + H2O = CO + H2, start from ~500ºC) and Boudouard reaction (from ~500ºC complete ~930ºC) form CO gas in the early part of sintering and can lead to large porosity, which lowers mechanical properties. With the use of careful powder drying, low dew point atmospheres and optimisation of heating profiles, densities in excess of 7.70g/cm3 were attained. The brittle microstructure, containing carbide networks and free of cracks, is transformed by intelligent heat treatment to a tougher one of ferrite plus sub-micron spheroidised carbides. This gives the potential for production of components, which are both tough and suitable for sizing to improve dimensional tolerance. Yield strengths up to 410 MPa, fracture strengths up to 950 MPa and strains of up to 16 % were attained. Forging experiments were subsequently carried out for spheroidised specimens of Fe-0.85Mo+06Si+1.4C, for different strain rates of 10-3, 10-2, 10-1 and 1sec-1 and heated in argon to 700¿C, density ~7.8g/cm3 and 769 MPa yield strength were obtained. / Libyan Education Ministry Office