Thesis (Ph. D.)--Rijksuniversiteit Groningen, 1997. / Includes bibliographical references.

The global energy sector is facing a crisis caused by the increasing demand for energy. Non-renewable energy sources, such as fossil fuels produce greenhouse gases that are largely blamed for climate change. The Kyoto protocol requires industrialised nations to reduce their collective greenhouse gas emissions. Hydrogen as an alternative fuel can serve as a substitute. Hydrogen production is expensive and the gas is largely derived from fossil fuels by a process that releases large quantities of greenhouse gases. In South Africa work on hydrogen production was first done on the Hybrid Sulphur cycle. The high operating temperature and highly corrosive environment involved in the process makes this cycle difficult to work with. The copper-chloride cycle has a lower operating temperature and uses less corrosive materials, making the cycle potentially more economical. Evaluation of the cycle started with the development of four models: the Base model, the Canadian model (developed in Canada) the Kemp model and the Excess model. The Kemp model has the best overall efficiency of 40.89 %, producing hydrogen at a cost of US$4.48/kg. The model does not however provide the excess steam required for the cycle. The Excess model which is based on the Kemp model does provide the excess steam and produces an overall efficiency of 39 % and hydrogen at a cost of US$4.60/kg. The copper-chloride cycle has an improved efficiency and produces hydrogen at a lower cost when compared to the hybrid sulphur cycle. The final conclusion of this thesis is that the copper-chloride cycle should be investigated further and an expected capital and operational costs estimate should be developed to obtain more accurate figures. / Thesis (M.Ing. (Nuclear Engineering))--North-West University, Potchefstroom Campus, 2012.

The global energy sector is facing a crisis caused by the increasing demand for energy. Non-renewable energy sources, such as fossil fuels produce greenhouse gases that are largely blamed for climate change. The Kyoto protocol requires industrialised nations to reduce their collective greenhouse gas emissions. Hydrogen as an alternative fuel can serve as a substitute. Hydrogen production is expensive and the gas is largely derived from fossil fuels by a process that releases large quantities of greenhouse gases. In South Africa work on hydrogen production was first done on the Hybrid Sulphur cycle. The high operating temperature and highly corrosive environment involved in the process makes this cycle difficult to work with. The copper-chloride cycle has a lower operating temperature and uses less corrosive materials, making the cycle potentially more economical. Evaluation of the cycle started with the development of four models: the Base model, the Canadian model (developed in Canada) the Kemp model and the Excess model. The Kemp model has the best overall efficiency of 40.89 %, producing hydrogen at a cost of US$4.48/kg. The model does not however provide the excess steam required for the cycle. The Excess model which is based on the Kemp model does provide the excess steam and produces an overall efficiency of 39 % and hydrogen at a cost of US$4.60/kg. The copper-chloride cycle has an improved efficiency and produces hydrogen at a lower cost when compared to the hybrid sulphur cycle. The final conclusion of this thesis is that the copper-chloride cycle should be investigated further and an expected capital and operational costs estimate should be developed to obtain more accurate figures. / Thesis (M.Ing. (Nuclear Engineering))--North-West University, Potchefstroom Campus, 2012.

Proefschrift--Utrecht. / Errata slip inserted. "Stellingen" : [3] p. inserted. Bibliography: p. [74]-75.

Proefschrift--Utrecht. / Errata slip inserted. "Stellingen" : [3] p. inserted. Bibliography: p. [74]-75.

Thesis (Doctoral)--Universiteit van Amsterdam, 1982.

In this thesis, ammonia (NH3) decomposition was assessed as a fuel processing technology for producing on-demand hydrogen (H2) for portable and distributed fuel cell applications. This study was motivated by the present lack of infrastructure to generate H2 for proton exchange membrane (PEM) fuel cells. An overview of past and recent worldwide research activities in the development of reactor technologies for portable and distributed hydrogen generation via NH3 decomposition was presented in Chapter 2. The objective was to uncover the principal challenges relating to the state-of-the-art in reactor technology and obtain a basis for future improvements. Several important aspects such as reactor design, operability, power generation capacity and efficiency (conversion and energy) were appraised for innovative reactor technologies vis-à-vis microreactors, monolithic reactors, membrane reactors, and electrochemical reactors (electrolyzers). It was observed that substantial research effort is required to progress the innovative reactors to commercialization on a wide basis. The use of integrated experimental-mathematical modelling approach (useful in attaining accurately optimized designs) was notably non-existent for all reactors throughout the surveyed openliterature. Microchannel reactors were however identified as a transformative reactor technology for producing on-demand H2 for PEM cell applications. Against this background, miniaturized H2 production in a stand-alone ammonia-fuelled microchannel reactor (reformer) washcoated with a commercial Ni-Pt/Al2O3 catalyst (ActiSorb® O6) was demonstrated successfully in Chapter 3. The reformer performance was evaluated by investigating the effect of reaction temperature (450–700 °C) and gas-hourly-space-velocity (6 520–32 600 Nml gcat -1 h-1) on key performance parameters including NH3 conversion, residual NH3 concentration, H2 production rate, and pressure drop. Particular attention was devoted to defining operating conditions that minimised residual NH3 in reformate gas, while producing H2 at a satisfactory rate. The reformer operated in a daily start-up and shut-down (DSS)-like mode for a total 750 h comprising of 125 cycles, all to mimic frequent intermittent operation envisaged for fuel cell systems. The reformer exhibited remarkable operation demonstrating 98.7% NH3 conversion at 32 600 Nml gcat -1 h-1 and 700 °C to generate an estimated fuel cell power output of 5.7 We and power density of 16 kWe L-1 (based on effective reactor volume). At the same time, reformer operation yielded low pressure drop (<10 Pa mm-1) for all conditions considered. Overall, the microchannel reformer performed sufficiently exceptional to warrant serious consideration in supplying H2 to low-power fuel cell systems. In Chapter 4, hydrogen production from the Ni-Pt-washcoated ammonia-fuelled microchannel reactor was mathematically simulated in a three-dimensional (3D) CFD model implemented via Comsol Multiphysics™. The objective was to obtain an understanding of reaction-coupled transport phenomena as well as a fundamental explanation of the observed microchannel reactor performance. The transport processes and reactor performance were elucidated in terms of velocity, temperature, and species concentration distributions, as well as local reaction rate and NH3 conversion profiles. The baseline case was first investigated to comprehend the behavior of the microchannel reactor, then microstructural design and operating parameters were methodically altered around the baseline conditions to explore the optimum values (case-study optimization). The modelling results revealed that an optimum NH3 space velocity (GHSV) of 65.2 Nl gcat -1 h-1 yields 99.1% NH3 conversion and a power density of 32 kWe L-1 at the highest operating temperature of 973 K. It was also shown that a 40-μm-thick porous washcoat was most desirable at these conditions. Finally, a low channel hydraulic diameter (225 μm) was observed to contribute to high NH3 conversion. Most importantly, mass transport limitations in the porouswashcoat and gas-phase were found to be negligible as depicted by the Damköhler and Fourier numbers, respectively. The experimental microchannel reactor produced 98.2% NH3 conversion and a power density of 30.8 kWe L-1 when tested at the optimum operating conditions established by the model. Good agreement with experimental data was observed, so the integrated experimental-modeling approach used here may well provide an incisive step toward the efficient design of ammonia-fuelled microchannel reformers. In Chapter 5, the prospect of producing H2 via ammonia (NH3) decomposition was evaluated in an experimental stand-alone microchannel reactor wash-coated with a commercial Cs-promoted Ru/Al2O3 catalyst (ACTA Hypermec 10010). The reactor performance was investigated under atmospheric pressure as a function of reaction temperature (723–873 K) and gas-hourly-space-velocity (65.2–326.1 Nl gcat -1 h-1). Ammonia conversion of 99.8% was demonstrated at 326.1 Nl gcat -1 h-1 and 873 K. The H2 produced at this operating condition was sufficient to yield an estimated fuel cell power output of 60 We and power density of 164 kWe L-1. Overall, the Ru-based microchannel reactor outperformed other NH3 microstructured reformers reported in literature including the Ni-based system used in Chapter 3. Furthermore, the microchannel reactor showed a superior performance against a fixed-bed tubular microreactor with the same Ru-based catalyst. Overall, the high H2 throughput exhibited may promote widespread use of the Ru-based micro-reaction system in high-power applications. Four peer-reviewed journal publications and six conference publications resulted from this work. / PhD (Chemical Engineering), North-West University, Potchefstroom Campus, 2015

In this thesis, ammonia (NH3) decomposition was assessed as a fuel processing technology for producing on-demand hydrogen (H2) for portable and distributed fuel cell applications. This study was motivated by the present lack of infrastructure to generate H2 for proton exchange membrane (PEM) fuel cells. An overview of past and recent worldwide research activities in the development of reactor technologies for portable and distributed hydrogen generation via NH3 decomposition was presented in Chapter 2. The objective was to uncover the principal challenges relating to the state-of-the-art in reactor technology and obtain a basis for future improvements. Several important aspects such as reactor design, operability, power generation capacity and efficiency (conversion and energy) were appraised for innovative reactor technologies vis-à-vis microreactors, monolithic reactors, membrane reactors, and electrochemical reactors (electrolyzers). It was observed that substantial research effort is required to progress the innovative reactors to commercialization on a wide basis. The use of integrated experimental-mathematical modelling approach (useful in attaining accurately optimized designs) was notably non-existent for all reactors throughout the surveyed openliterature. Microchannel reactors were however identified as a transformative reactor technology for producing on-demand H2 for PEM cell applications. Against this background, miniaturized H2 production in a stand-alone ammonia-fuelled microchannel reactor (reformer) washcoated with a commercial Ni-Pt/Al2O3 catalyst (ActiSorb® O6) was demonstrated successfully in Chapter 3. The reformer performance was evaluated by investigating the effect of reaction temperature (450–700 °C) and gas-hourly-space-velocity (6 520–32 600 Nml gcat -1 h-1) on key performance parameters including NH3 conversion, residual NH3 concentration, H2 production rate, and pressure drop. Particular attention was devoted to defining operating conditions that minimised residual NH3 in reformate gas, while producing H2 at a satisfactory rate. The reformer operated in a daily start-up and shut-down (DSS)-like mode for a total 750 h comprising of 125 cycles, all to mimic frequent intermittent operation envisaged for fuel cell systems. The reformer exhibited remarkable operation demonstrating 98.7% NH3 conversion at 32 600 Nml gcat -1 h-1 and 700 °C to generate an estimated fuel cell power output of 5.7 We and power density of 16 kWe L-1 (based on effective reactor volume). At the same time, reformer operation yielded low pressure drop (<10 Pa mm-1) for all conditions considered. Overall, the microchannel reformer performed sufficiently exceptional to warrant serious consideration in supplying H2 to low-power fuel cell systems. In Chapter 4, hydrogen production from the Ni-Pt-washcoated ammonia-fuelled microchannel reactor was mathematically simulated in a three-dimensional (3D) CFD model implemented via Comsol Multiphysics™. The objective was to obtain an understanding of reaction-coupled transport phenomena as well as a fundamental explanation of the observed microchannel reactor performance. The transport processes and reactor performance were elucidated in terms of velocity, temperature, and species concentration distributions, as well as local reaction rate and NH3 conversion profiles. The baseline case was first investigated to comprehend the behavior of the microchannel reactor, then microstructural design and operating parameters were methodically altered around the baseline conditions to explore the optimum values (case-study optimization). The modelling results revealed that an optimum NH3 space velocity (GHSV) of 65.2 Nl gcat -1 h-1 yields 99.1% NH3 conversion and a power density of 32 kWe L-1 at the highest operating temperature of 973 K. It was also shown that a 40-μm-thick porous washcoat was most desirable at these conditions. Finally, a low channel hydraulic diameter (225 μm) was observed to contribute to high NH3 conversion. Most importantly, mass transport limitations in the porouswashcoat and gas-phase were found to be negligible as depicted by the Damköhler and Fourier numbers, respectively. The experimental microchannel reactor produced 98.2% NH3 conversion and a power density of 30.8 kWe L-1 when tested at the optimum operating conditions established by the model. Good agreement with experimental data was observed, so the integrated experimental-modeling approach used here may well provide an incisive step toward the efficient design of ammonia-fuelled microchannel reformers. In Chapter 5, the prospect of producing H2 via ammonia (NH3) decomposition was evaluated in an experimental stand-alone microchannel reactor wash-coated with a commercial Cs-promoted Ru/Al2O3 catalyst (ACTA Hypermec 10010). The reactor performance was investigated under atmospheric pressure as a function of reaction temperature (723–873 K) and gas-hourly-space-velocity (65.2–326.1 Nl gcat -1 h-1). Ammonia conversion of 99.8% was demonstrated at 326.1 Nl gcat -1 h-1 and 873 K. The H2 produced at this operating condition was sufficient to yield an estimated fuel cell power output of 60 We and power density of 164 kWe L-1. Overall, the Ru-based microchannel reactor outperformed other NH3 microstructured reformers reported in literature including the Ni-based system used in Chapter 3. Furthermore, the microchannel reactor showed a superior performance against a fixed-bed tubular microreactor with the same Ru-based catalyst. Overall, the high H2 throughput exhibited may promote widespread use of the Ru-based micro-reaction system in high-power applications. Four peer-reviewed journal publications and six conference publications resulted from this work. / PhD (Chemical Engineering), North-West University, Potchefstroom Campus, 2015