The principal contributions of this study include the development of a new capacitive feeding mechanism for wideband probe-fed microstrip patch antennas as well as the implementation of a spectral-domain moment-method formulation for the efficient analysis of large, but finite arrays of these elements. Such antenna configurations are very useful in the wireless communications industry, but extremely difficult to analyse with commercially available software. Probe-fed microstrip patch antennas have always been a popular candidate for a variety of antenna systems. Due to their many salient features, they are well suited for modern wireless communication systems. However, these systems often require antennas with wideband properties, while an inherent limitation of probe-fed microstrip patch antennas is its narrow impedance bandwidth. This can be overcome by manufacturing the antenna on a thick low-loss substrate, but at the same time it also complicates things by rendering the input impedance of the antenna very inductive. In this thesis, a new capacitive feeding mechanism is introduced that can be used for probe-fed microstrip patch antennas on thick substrates. It consists of a small probe-fed capacitor patch that is situated next to the resonant patch. The benefits of this configuration include the fact that only one substrate layer is required to support the antenna. It is also very easy to design and optimise. The use of full-wave methods for an accurate analysis of microstrip antennas, has basically become standard practice. These methods can become very demanding in terms of computational resources, especially when large antenna arrays have to be analysed. As such, this thesis includes a spectral-domain moment-method formulation, which was developed for the analysis of probe-fed microstrip patch antennas or antenna arrays that comprise of the new capacitive feeding mechanism. Here, entire-domain and subdomain basis functions are combined in a unique way so as to minimise the computational requirements, most notably computer memory. It is shown that, for general antenna array configurations, memory savings of more than 2500 times can be achieved when compared with typical commercial software packages where only subdomain basis functions are used. Some of the numerical complexities that are dealt with, include various methods to evaluate the spectral integrals as well as special algorithms to eliminate the recalculation of duplicate interactions. The thesis also contains a quantitative comparison of various attachment modes that are often used in the moment-method modelling of probe-to-patch transitions. Various numerical and experimental results are included in order to verify the spectral-domain moment-method formulation, to characterise the new feeding mechanism and to illustrate its use for various applications. These results show that, in terms of accuracy, the spectral-domain moment-method formulation compares well with commercial codes, while by comparison, it demands very little computer memory. The characterisation results show that the input impedance of the antenna can be fully controlled by only adjusting the size of the capacitor patch as well as the width of the gap between the capacitor patch and the resonant patch. In terms of applications, it is shown how the new antenna element can effectively be employed in linear arrays with vertical polarisation, horizontal polarisation or dual slant-polarisation. These represent some widely-used configurations for modern base-station antennas. / Thesis (PhD (Electronic Engineering))--University of Pretoria, 2005. / Electrical, Electronic and Computer Engineering / unrestricted

No / A small dielectric resonator antenna has been designed for ultra wideband (UWB) communication system applications. The antenna element is a rectangular low permittivity ceramic block, with a dielectric constant of 9.4, and the modified T-shaped feed network includes a 50 ohm microstrip line to achieve strong coupling, and some bandwidth enhancement. The antenna performance is simulated and measured over a frequency band extending from 3100 MHz to 5500 MHz; the impedance bandwidth over this interval is 55.8% with VSWR <; 2, making the antenna suitable for UWB applications.

<p> The allocation of 7.5 GHz of bandwidth by the Federal Communication Commission (FCC) for ultra-wideband (UWB) applications has provided an exciting and a challenging opportunity to design short range wireless communication and microwave imaging systems. To fully realize the potential of the UWB, communication and microwave imaging systems are required to operate over the entire UWB frequency band. The combination of the wide bandwidth requirement and the target application of the UWB systems have led to a surge of interest in designing of novel integrated circuits and antennas for the UWB applications. In any wireless communication and microwave imaging system, the antenna has a fundamental effect on the overall performance of the system, and as a result, it has attracted considerable research interest.</p> <p> This thesis focuses on the design of UWB antennas that are suitable for UWB cancer detection and wireless communication systems. Two planar antennas, one a printed monopole antenna, and the other, a printed slot antenna fed with a coplanar waveguide, are presented in this work. First, the antennas have been designed to operate in air, making them suitable for the UWB wireless short range communication applications. Measurement and simulation results indicate that both antennas achieve input impedance matching in a bandwidth of more than 7.5 GHz. The effect on the input matching of the antennas due to the variation in their geometrical parameters has been studied and both antennas have been fully characterized in air. Next, the two antennas have been redesigned to operate in a coupling medium for medical imaging applications. Both antennas achieve return loss of less than -10 dB over the entire UWB spectrum. Also, the antennas have been fully characterized while operating in the coupling medium and in proximity to a human body model. Finally, a two-element antenna array, based on the printed monopole antenna and the printed slot antenna, in co- and cross-polarized array formation, has been designed. The tumor detection capabilities of all antenna arrays for different scenarios have been studied through electromagnetic simulation and measurements.</p> / Thesis / Master of Applied Science (MASc)

Thesis (PhD)--Stellenbosch University, 2015. / ENGLISH ABSTRACT: This dissertation presents modal-based techniques for the effective systematic design of quadruple-ridged flared horns (QRFHs) as reflector feeds for radio astronomy applications. A new excitation technique is proposed, consisting of a quadraxial line that terminates in the quad-ridges through the back lid of the QRFH, which allows for the integration with differential low-noise amplifiers. An equivalent circuit of this quadraxial feed is presented that allows fast synthesis of optimal feeding designs for QRFHs. In addition, the quadraxial feeding network suppresses higher-order modes significantly. The effect of eliminating these unwanted modes are investigated and the quadraxial feed is shown to outperform the coaxial feed in the known detrimental aspects of the QRFH – beamwidth narrowing for increased frequency, beamwidth variation over the upper bandwidth, high cross-polarisation levels, high co-polar sidelobes and variable phase centre – for the specific QRFH designs. Ridge-loaded modes are analysed and a large number of cut-off frequencies presented which are unavailable in literature. The pure-mode excitation of the quadraxial feed allows more effective control over the modal content in the QRFH. This is exploited in a proposed design technique where the cut-off frequencies throughout the horn are used to synthesise the ridge taper profile, in order to achieve the desired modal distribution in the aperture. The proposed feeding solution is compact and therefore is also attractive for use with cryocoolers, typically employed with front-end electronics in telescopes for radio astronomy. A prototype was successfully manufactured and the mechanical implementation of the quadraxial feed proved to be much more simple than that of the conventional feed – consisting of a coaxial line realised within the thin ridges. / AFRIKAANSE OPSOMMING: Hierdie proefskrif stel modus gebasseerde tegnieke voor vir die effektiewe sistematiese ontwerp van viervoud gerifte oopgesperde horings (VGOHs) as weerkaatser voere vir radio astronomie toepassings. ’n Nuwe voertegniek word voorgestel, wat bestaan uit ’n kwadraksiale lyn wat termineer in die vier riwwe deur die agterkant van die VGOH, wat die integrasie met differensiële laeruis versterkers toelaat. ’n Ekwivalente stroombaan van hierdie kwadraksiale voer word aangebied vir die vinnige sintese van optimale voer ontwerpe vir VGOHs. Boonop onderdruk die kwadraksiale voer netwerk ook beduidend hoër orde modusse. Die effek van die uitskakeling van hierdie ongewensde modusse word ondersoek en die kwadraksiale voer oortref die gedrag van die koaksiale voer in die bekende nadelige aspekte van die VGOH – bundelwydte vernouing met toenemende frekwensie, bundelwydte variasie oor die boonste bandwydte, hoë kruispolarisasie vlakke, hoë kopolarisasie sybande en wisselvallige fase senter – vir die spesifieke VGOH ontwerpe. Rifgelaaide modusse word geanaliseer en ‘n groot aantal afsnyfrekwensies word aangebied wat nie beskikbaar is in literatuur nie. Die suiwermodus opwekking van die kwadraksiale voer bied meer effektiewe beheer oor die modusinhoud in die VGOH. Hierdie aspek word benut in ‘n voorgestelde tegniek waar die afsnyfrekwensies deur die horing gebruik word om die rif tapsheid profiel te sintetiseer, sodat die gewensde modale distribusie in die stralingsvlak behaal word. Die voorgestelde voer oplossing is kompak en daarom ook aantreklik vir die gebruik met krioverkoelers, wat tipies gebruik word met die voorkant elektronika in teleskope vir radio astronomie. ‘n Prototipe was suksesvol vervaardig en die meganiese implimentasie van die kwadraksiale voer toon dat dit eenvoudiger is as met die gebruiklike koaksiale voer – wat bestaan uit ‘n koaksiale lyn bewerkstellig binne die dun riwwe.

Cette thèse s’intéresse à la conception d’antennes ultra large bande reconfigurables. Cette étude a été motivée par le souhait de regrouper l’ensemble des antennes d’observation présentes sur les satellites en un panneau rayonnant unique afin de pouvoir réduire la taille de ces derniers. Les travaux présentés dans ce mémoire sont donc principalement axés sur la conception d’antennes spirales et sur les améliorations qui peuvent leur être apportées. Ainsi, une nouvelle topologie d’antenne spirale carrée reconfigurable en un réseau de quatre antennes spirales carrées plus petites sur la même ouverture rayonnante est exposée. Cette reconfiguration permet d’augmenter l’efficacité de surface de la structure tout en offrant de nouvelles possibilités d’utilisation à l’antenne et en améliorant ses performances. Les caractéristiques et les performances des deux configurations en états figés sont détaillées. Les maquettes réalisées et les résultats de mesure sont également présentés afin de valider le fonctionnement de l’antenne. Ensuite, différentes améliorations de cette structure sont présentées ainsi qu’une application possible. Enfin, une solution permettant d’améliorer le fonctionnement des antennes spirales imprimées au-dessus d’un plan de masse est décrite. En effet, cette solution permet de supprimer un nul de rayonnement lorsque l’antenne se situe à une demi-longueur d’onde du plan de masse. Sa bande passante d’utilisation peut ainsi être potentiellement doublée sans perdre la moitié de l’énergie comme avec l’utilisation d’absorbants. Cette technique consiste à ajouter un élément rayonnant parasite au-dessus de l’antenne. Cet élément est excité par couplage à l’antenne spirale et rayonne à la fréquence du nul de rayonnement. Cet élément étant faible bande, il ne dégrade pas le fonctionnement de l’antenne aux autres fréquences de la bande passante. Une structure utilisant ce concept a été réalisée afin de valider son fonctionnement. / This thesis focuses on the design of ultrawideband reconfigurable antennas. The objective of this study is to integrate all the antennas of observation on satellites into a single radiating panel and make it reconfigurable. Works presented in this document are focused on the design of spiral antennas and on their possible improvements. Thereby, a new topology of square spiral antenna reconfigurable into an array of four smaller square spiral antennas is shown. This reconfiguration allows increasing the surface efficiency of the structure while offering new possibilities of utilization to the antenna and improving its performance. Characteristics and performance of both configurations in frozen states are presented. Breadboards and measurements are also presented in order to validate the functioning of the antenna. Then, several improvements of this structure are studied and a possible application. Finally, a solution for improving the functioning of spiral antennas printed over a metallic ground plane is presented. This solution permits to remove a null of radiation when the distance between the antenna and the ground plane is a multiple of the half wavelength. In this way, its bandwidth can be doubled without losing the half of the energy like with absorbers. This technique consists in adding a parasitic radiating element over the antenna. This element is fed by coupling to the spiral antenna and radiates at the frequency of the null of radiation. This element is narrowband, so antenna performance remains unchanged at the other frequencies of the bandwidth. A structure using this concept has been made in order to validate its functioning.

This work details the design and fabrication of an ultra-wideband periodic spiral antenna (PSA) with a notch filter embedded directly into the radiating aperture. Prototype fabrication of the PSA reveals long assembly time due to forming the antenna element, therefore modifications are made to allow fabricating the antenna elements on a thin, flexible, Polyimide substrate. A transmission line model is develop to support the updated configuration of the antenna elements. In addition, a symmetric spurline filter is integrated into the arms of the spiral antenna in order to address the common problem of interference in ultra-wideband systems. For the first time, a placement study is conducted to show the optimal location of the filter as a function of frequency. The presented transmission line model demonstrates the ability to decouple the design of the filter and antenna by being able to predict the resonant frequency and achieved rejection after integration of the two. Measured results show a gain rejection of 21 dB along with the ability to tune the resonance of the filter from 1.1 – 2.7 GHz using a lumped capacitor. For high power applications, thermal measurements are conducted, and for the first time, thermal profiles along the top of the antenna are used to show the radiation bands in a spiral antenna. Power tests are successfully conducted up to 40 W across the entire operational bandwidth and up to 60 W for 2 GHz and below. At these elevated power levels, a large voltage is generated across the lumped capacitor used to tune the resonance of the spurline filter; this issue is addressed through the development of a capacitive wedge that is overlapped on top of the spurline stub, which increases the voltage handling to 2,756 V. Measured results reveal a reduced tuning range compared to using lumped capacitors and a gain rejection of greater than 10 dB for all configurations.

Historical, well developed, procedures for RF design have minimal emphasis on exploring the third dimension due to the difficulty of fabrication. Recent material advancements applicable to 3D printing have brought about low-loss thermoplastics with excellent mechanical properties. Research into depositing conductive inks onto arbitrary 3D shapes has achieved resolutions better than 50 μm with conductivity values approaching that of copper cladding. The advancements in additive manufacturing have improved reliability and repeatability of three dimensional designs while decreasing fabrication time. With this design approach other considerations, such as stability and strength, can be concentrated on during the structure design to realize new shapes. The next step in the future of RF research will encompass designing and further understanding the benefits and consequences of using all three dimensions. This could include meandering an antenna element around other electronic components to make the overall package size smaller or integrating an antenna array into a wing. The design and analysis of the periodic spiral antenna (PSA) takes a look at a specific case of full volume utilization. In this application meandering in the z-dimension allowed the design to become smaller and more efficient than what is achievable with planar methods. This thesis will go into detail on the characterization of the periodic spiral antenna. To exemplify the benefits of meandering in the z-dimension a loop antenna is presented and benchmarked against other miniaturization techniques. Measured results of two different PSA models are presented and remarks on improving fabrication are given. When an antenna is used as a transmitter incident power will cause thermal generation so a study was conducted to understand how material properties can govern the amount of heat generated.

This thesis presents the designs of Ultra-wideband (UWB) monopole antennas, textile monopole antennas and transparent UWB textile antennas using planar technology for body-centric wireless communications (BCWC). A planar antenna designed using offset-fed and slotted ground plane to extend the operating bandwidth for the industrial, scientific and medical (ISM)band and UWB is proposed. Results show that the antenna can achieve a bandwidth from 2.38 to 14.5 GHz with omni-directional radiation patterns in the E-plane. Agroup of nine planar UWB monopole antennas using different radiator shapes such as triangle, rectangle, square, annual ring, circle, horizontal ellipse, vertical ellipse, pentagon and hexagon for BCWC is studied using computer simulation and measurement. Results show that the monopole antenna having a vertical-elliptical-shape radiator has a relatively better performance than other monopole antennas. Three textile antennas fabricated on fabric materials are studied. The first design is a triple-band textile antenna for wireless-local-area network (WLAN) and worldwide interoperability for microwave access (WiMAX) wireless communication applications. The radiator is composed of two branches and a short stub to generate the resonances at about 2.45, 3.5 and 5.5 GHz, respectively. Simulated and measured results show that the three frequency bands can be set independently. The second design is an UWB antenna consisting of a circular radiator, a tapered feed line and a slotted ground plane. Results show that the antenna can achieve a bandwidth of 3 to 12 GHz. The third design is a compact belt-loop UWB antenna with microstrip-fed. The antenna has a simple elliptical-shaped radiator, a three-step staircase on both sides of the feed line and a slot on the ground plane. It has a very compactsize of 11×40=440 mm2and can still achieve a bandwidth of 3.1 to 12.8 GHz. To emulate the on-body conditions, the two UWB antennas are studied in the bending and crumpling conditions due to the curvature of human body. Results show that both UWB textile antennas have quite stable performances throughout the UWB band. The two UWB textile antennas are re-designed using a transparent conductive film (TCF)as the radiator and ground plane on fabric substrate. Results show that the measured reflection coefficients of transparent antennas agree well with the simulated results. However, the measured radiation patterns have large discrepancies with the simulated results, which are mainly due to the uncertain electric properties of TCF in radio frequency. Results show that the antennas have a better performance, in terms ofbandwidth, peak gain and radiation efficiency ,than those of other transparent antennas studied before, making our proposed antennas suitable for body-centric wireless communications. / published_or_final_version / Electrical and Electronic Engineering / Doctoral / Doctor of Philosophy

This thesis investigates omnidirectional and directional ultra wideband (UWB) antennas for communication and microwave imaging applications. To reduce interference with existing technologies, monopole antennas with efficient band-stop functions are introduced. Single and double slots acting as series resonators are used. Reduction in the antenna gain in the stop-band regions of about 19.5 dB is achieved. Central metal removal and ground plane size effects on the antenna performance are investigated. To eliminate signal distortion caused by such monopole antennas, phase centre behaviour over the entire frequency band of operation is investigated at different principle planes, which have not been done before. This study will also show how these antennas act in different communication scenarios and where the radiation will be coming from at different frequencies. The effect of including different slots with different shapes on the performance of phase centre of these antennas is also investigated. Different methods to minimize the antenna phase centre movement are studied. Novel microstrip antennas with UWB impedance and radiation pattern bandwidth and low cross polarization components are introduced to work over the frequency band from 3 to 20 GHz. The antennas introduced are double-layer structures in which the radiator is sandwiched between two identical partial ground planes or a partial ground plane is sandwiched between two radiators. Results show a significant reduction in the cross polarization components at all frequencies. A novel high gain UWB Vee dipole antenna with a UWB coaxial balun feed is introduced to cover the existing and future UWB communication applications. Different type of loadings such as a reflecting ground below the antenna, a dielectric sleeve over the UWB balun and conical dielectrics between the Vee plates are also used and studied that show enhanced gains and lower sidelobes. A miniaturized-type UWB Vee dipole antenna is also investigated for microwave imaging applications. The antenna has a small radiation aperture which makes it a good candidate for array type applications. Full wave analysis of studied antennas are done using Ansoft HFSS, finite-element-methods based software. Experimental investigations are done to confirm the accuracy of simulated results.

This thesis investigates omnidirectional and directional ultra wideband (UWB) antennas for communication and microwave imaging applications. To reduce interference with existing technologies, monopole antennas with efficient band-stop functions are introduced. Single and double slots acting as series resonators are used. Reduction in the antenna gain in the stop-band regions of about 19.5 dB is achieved. Central metal removal and ground plane size effects on the antenna performance are investigated. To eliminate signal distortion caused by such monopole antennas, phase centre behaviour over the entire frequency band of operation is investigated at different principle planes, which have not been done before. This study will also show how these antennas act in different communication scenarios and where the radiation will be coming from at different frequencies. The effect of including different slots with different shapes on the performance of phase centre of these antennas is also investigated. Different methods to minimize the antenna phase centre movement are studied. Novel microstrip antennas with UWB impedance and radiation pattern bandwidth and low cross polarization components are introduced to work over the frequency band from 3 to 20 GHz. The antennas introduced are double-layer structures in which the radiator is sandwiched between two identical partial ground planes or a partial ground plane is sandwiched between two radiators. Results show a significant reduction in the cross polarization components at all frequencies. A novel high gain UWB Vee dipole antenna with a UWB coaxial balun feed is introduced to cover the existing and future UWB communication applications. Different type of loadings such as a reflecting ground below the antenna, a dielectric sleeve over the UWB balun and conical dielectrics between the Vee plates are also used and studied that show enhanced gains and lower sidelobes. A miniaturized-type UWB Vee dipole antenna is also investigated for microwave imaging applications. The antenna has a small radiation aperture which makes it a good candidate for array type applications. Full wave analysis of studied antennas are done using Ansoft HFSS, finite-element-methods based software. Experimental investigations are done to confirm the accuracy of simulated results.