Low Reynolds number airfoil analysis has become increasingly significant as urban air mobility vehicles and unmanned aerial vehicles surge in popularity. The Green Raven project at KTH Aero aims to use reflex airfoils where little data is available beyond classical analysis. Viscous formulations of the panel method and computational fluid dynamics (CFD) have been used to simulate lift, drag and moments for the MH61 and MH104 airfoils at different angles of attack (AOAs). XFOIL and CFD turbulence models such as Spalart-Allmaras (SA), k-w Shear Stress Transport (SST) with and without damping coefficients were used. The strengths and limitations of each model were used to justify results. Due to clear computational advantages, XFOIL produced adequate results and is tailored toward use in initial design stages where repeated measurements are crucial. The SA turbulence stood out as the model produced accurate results in a reasonable time. The abundance of published CFD material comparing different turbulence models increased the credibility of the results. The two airfoils had similar lift and drag characteristics at AOAs of 0-6 deg while the MH104 was superior near stall. However, due to the lack of experimental data of the airfoils no particular model could be commended or verified.

This dissertation consists of three main parts. The first part is to discuss aileron reversal problem for a typical section with linear aerodynamic and structural analysis. The result gives some insight and ideas for this aeroelastic problem. Although the aileron in its post-reversal state will work the opposite of its design, this type of phenomenon as a design root should not be ruled out on these grounds alone, as current active flight-control systems can compensate for this. Moreover, one can get considerably more (negative) lift for positive flap angle in this unusual regime than positive lift for positive flap angle in the more conventional setting. This may have important implications for development of highly maneuverable aircraft. The second part is to involve the nonlinear aerodynamic and structural analyses into the aileron reversal problem. Two models, a uniform cantilevered lifting surface and a rolling aircraft with rectangular wings, are investigated here. Both models have trailing-edge control surfaces attached to the main wings. A configuration that reverses at a relatively low dynamic pressure and flies with the enhanced controls at a higher level of effectiveness is demonstrated. To evaluate how reliable for the data from XFOIL, the data for the wing-aileron system from advanced CFD codes and experiment are used to compare with that from XFOIL. To enhance rolling maneuverability for an aircraft, the third part is to search for the optimal configuration during the post-reversal regime from a design point of view. Aspect ratio, hinge location, airfoil dimension, inner structure of wing section, composite skin, aeroelastic tailoring, and airfoil selection are investigated for cantilevered wing and rolling aircraft models, respectively. Based on these parametric structural designs as well as the aerodynamic characteristics of different airfoils, recommendations are given to expand AAW flight program.

Thesis (MScEng (Department of Mechanical and Mechatronic Engineering))--Stellenbosch University, 2006. / ENGLISH ABSTRACT: Wind conditions in South Africa determine the need for a small-scale wind turbine to produce useable power at windspeeds below 7m/s. In this project, a range of windspeeds, within which optimal performance o the wind turbine is expected, was selected. The optimal performance was assessed in terms of the Coefficient of Power(Cp), which rates the turbines blade's ability to extract energy form the avalible wind stream. The optimisation methods employed allowed a means of tackling the multi-variable problem such that the aerodynamic characteristics of the blade were ideal throughout the wind speed range. The design problem was broken down into a two-dimensional optimisaion of the airfoils used at the radial stations, and a three-dimensional optimisation of the geometric features of the wind rotor. by means of blending various standard airfoil profiles, a new profile was created at each radial station. XFOIL was used for the two-dimensional analysis of these airfoils. Three-dimensional optimisn involved representation of the rotor as a simplified model and use of the Blade Element Momentum(BEM) method for analysis. an existimg turbine blade, on which the design specifications were modelled, was further used for comparative purposes throughout the project. The resulting blade design offers substantial improvements on the reference design. The application of optimisation methods has successfully aided the creation of a wind turbine blade with consistent peak performance over a range of design prints. / Sponsored by the Centre for Renewable and Sustainable Energy Studies, Stellenbosch University

This master’s thesis is focused on optimization of rear wing of sport car by using open-source software. The optimization of 2D profile of the rear wing is present in this thesis. Python environment was chosen for optimization and evolutionary algorithm was is used as optimization function. This algorithm is further connected to Xfoil software, which is computing aerodynamic characteristic. The ratio of the lift and drag coefficients (C_L/C_D) is chosen as parameter which considers the aerodynamic efficiency. The CFD computation of flowing around the whole car is provided in open-source software OpenFOAM. . The profile optimization results to approximately 7.9 % raise of the parameter C_L/C_D, in the same wing stability. The main benefit of this work is to use open-source software for the optimization and CFD analysis, which in future might save company’s resources by not buying expensive commercial software licenses.