Catalysis using nanostructures has been a topic of substantial interest for fundamental studies and for practical applications in energy and environmental sectors. The growing demand for production of energy and in the cleaning of polluting hazardous vehicles/industrial wastes has led to several studies in catalysis. Despite the substantial growth of heterogeneous catalytic technologies in last decade, they are still far from reaching their full potential in terms of efficiency, selectivity as well as durability. It is often difficult to simultaneously tackle all the mentioned issues with single component catalysts. Most of these challenges are being overcome with heterostructures/supported hybrid catalysts by modifying their interfaces. The properties of heterostructures hybrids arises not only from the individual contributions of the individual components but also from strong synergetic effect arising from the interface. Engineering the interfaces provides pathways to promote the catalytic performance and hence has been explored. In this regard, we have focused on the progress in investigating the active interfaces that affect the performance of metal oxide-metal, semiconductor-metal and coupled semiconductor nanocatalyst hybrids. We explored a wide spectrum of their applications in photo catalytic, electrocatalytic as well as gas-phase reactions and highlighted the importance of the interface for overall performance. The entire study reported in the thesis is organized as follows: Chapter 1 is a general introduction of hybrid nanocatalyst and their role in wide spectra of catalytic reactions in photo/electro catalysis as well as gas-phase reactions. This chapter describes the motivation behind modulating the interface between two or more nanostructures to obtain multifunctional nanocatalysts. Nan catalysts to achieve high throughput with active interfaces are elaborated while indicating the role of morphology, internal induced state, charge transfer, geometric, support, as well as electronic effect for enhanced performance. Motivation behind specific nanocatalyst hybrid, synthesis routes as well as characterization techniques are detailed in the respective chapters. Specific details for different hybrids are described in the following chapters. Chapter 2 describes the synthesis of high dense ultrathin Au wires on ZnO nanorods for electrocatalytic oxidation of ethanol, where the prerequisite step is the formation of amine-modified support. Oleylamine modification not only serves to anchor Au nanowires on ZnO but also passivates surface defects of ZnO, which in turn enhances the photocurrent. In addition to the stability, the support induces electronic effect on Au nanowires, which facilitates redox process at low potential. Most importantly, the support promotes the activity of Au nanowires upon photoirradiation, and thus leading to synergy between electro and photooxidation current. This is of immense importance for photofuel cell technologies. Moreover, the method enabled the first time electrocatalysis on these nanowires that revealed ultrathin nanowires are potentially interesting systems for catalysis applications provided they are stabilized by a suitable support. Chapter 3 deals with the growth of ultrathin Au nanowires on metal oxide (TiO2) coupled with graphene hybrid support in order to overcome the low conductivity of metal oxide. Oleylamine, used for growth of Au nanowires simultaneously functionalizes the support and leads to room temperature GO reduction. With respect to catalytic activity, we also synthesized the binary counterparts (rGO/Au, TiO2/Au ultrathin nanowires) to delineate the contribution of each of the components to the overall electrocatalytic oxidation of ethanol. Comparative analysis of photo and electrocatalytic activity between the different binary and ternary hybrids provides interesting information. Both, electronic effect of TiO2 and electrical conductivity of rGO add their specific beneficial to the nanowires, leading to superior ternary system. Chapter 4 rGO supported ultrathin Au nanowires exhibits high electrocatalytic performance for oxidation of borohydride with a lower onset potential compared to rGO/Au nanoparticles. Electrochemical impedance spectroscopy measurements display abnormal inductive behavior of the synthesized hybrids, indicative of Au surface reactivation. DFT calculations indicate that the origin of the high activity stems from the shift in the position of the Au d-band center. Chapter 5 Different aspect ratio ZnO nanostructures are obtained by varying the solvothermal reaction time. We observed a direct correlation between observed photocatalytic activity, measured photocurrent and length of the ZnO nanorods. Furthermore, photoresponse of the high aspect ratio ZnO nanorods are improved by attaching Au nanoparticles, intimate contact of two components leads to band bending. Thus, the synthesized ZnO/Au heterostructure favors for prominent separation of photogenerated charge carriers. Chapter 6 TiO2 and PbO/TiO2 hybrids are synthesized via non–hydrolytic sol–gel combustion method. Hybrid exhibits higher photocatalytic activity for the degradation of dye than TiO2. The estimated photogenerated species reveals that the origin of enhanced activity stems from the direct oxidization of dye via photogenerated hole rather than radicals. The semiconductors are matched based on their band edge positions, for the formation of energetic radicals to degrade the pollutants. Based on this study, we infer that semiconductors should not neglected (for example Si) based on calculated mismatch of their valence band edges position for photooxidation reaction via radicals. Chapter 7 describes the Pd dopant associated band engineering, a strategy for tuning the optoelectronic properties of ZnO towards enhanced photocatalytic activity. Incorporated Pd heterocation induces internal energy states within the ZnO band gap. The created energy level leads to trends mismatch between photocatalytic activity and measured photocurrent. Formed energy level arrests the photogenerated electrons, which make them not contribute for the photocurrent generation. Hence, the isolated photogenerated hole efficiently oxidizes the pollutants through hydroxyl radicals, and thus leads to enhanced photocatalytic activity. Chapter 8 employed Pd-substituted zinc stannate for CO oxidation as heterogeneous catalyst for the first time. Compared with SnO2 support, zinc stannate based materials exhibits abnormal sudden light-off profiles at selective temperatures. On the basis of DRIFT studies under relevant conditions, we find that the initially formed product gets adsorbed over the catalyst surface. It leads to the accumulation of carbonates as a consequence, both lattice oxygen mobility and further CO interactions are disabled. As soon as Sn redox nature dominates over the accumulated carbonates, this leads to sudden release of lattice oxygen, and thus leads to a sudden full conversion. Therefore, choosing the suitable support material greatly influences the nature of the light-off CO oxidation profile. Chapter 9 Although, reducible oxide supported gold nanostructures exhibits the highest CO oxidation activity; they still suffer from problems such as limited selectivity towards CO in the presence of H2. Both ex-situ and in-situ experiments demonstrate that, Au nanoparticles supported on Zn2SnO4 matrix selectively oxidizes CO. DRIFT experiments revealed that the involvement of OH groups leads to the formation of hydroxycarbonyl under PROX conditions. Chapter 10 This chapter discusses the conclusions for the previous chapters and highlights the possibilities for future scope for the developed nanocatalysts hybrids for energy and environmental applications.

Synopsis of thesis entitled “Electrochemical and Photoelectrochemical Investigations of Co, Mn and Ir-based Catalysts for Water Splitting” by Ahamed Irshad M (SR No: 02-01-02-10-11-11-1-08823) under the supervision of Prof. N. Munichandraiah, Department of Inorganic and Physical Chemistry, Indian Institute of Science, Bangalore (India), for the Ph.D. degree of the Institute under the Faculty of Science. Hydrogen is considered as the fuel for future owing to its high gravimetric energy density and eco-friendly use. In addition, H2 is an important feedstock in Haber process for ammonia synthesis and petroleum refining. Although, it is the most abundant element in the universe, elemental hydrogen is not available in large quantities on the planet. Consequently, H2 must be produced from its various chemical compounds available on earth. Currently, H2 is produced in large scale from methane by a process called steam-methane reforming (SMR). This process releases huge amount of CO2 into atmosphere as the by-product causing serious environmental issues. The development of alternate clean methods to generate H2 is a key challenge for the realization of hydrogen economy. Production of H2 gas by water splitting using electricity or sunlight is known. Low cost, high natural abundance and carbon neutrality make water as the best source of hydrogen. Thermodynamically, splitting of H2O needs 237 kJ mol-1 of energy, which corresponds to 1.23 V according to the equation, ΔG = -nFE. However, commercial electrolyzers usually operate between 1.8 to 2.1 V, due to the need of large overvoltage. The high overvoltage and subsequent energy losses are mainly associated with the sluggish kinetics of oxygen evolution reaction (OER) at the anode and hydrogen evolution reaction (HER) at the cathode. The overvoltage can be considerably reduced using suitable catalysts. Hence, the design and development of stable, robust and highly active catalysts for OER and HER are essential to make water splitting efficient and economical. Attempts in the direction of preparing several novel OER and HER catalysts, physicochemical characterizations and their electrochemical or photoelectrochemical activity are described in the thesis. A comprehensive review of the literature on various types of catalysts, thermodynamics, kinetics and mechanisms of catalysis are provided in the Chapter 1 of the thesis. Chapter 2 furnishes a brief description on various experimental techniques and procedures adopted at different stages of the present studies. Chapter 3 explains the results of the studies on kinetics of deposition and stability of Nocera’s Co-phosphate (Co-Pi) catalyst using electrochemical quartz crystal microbalance (EQCM). The in-situ mass measurements during CV experiments on Au electrode confirm the deposition of Co-Pi at potential above 0.87 V vs. Ag/AgCl, 3 M KCl (Fig.1a and b). The catalyst is found to deposit via a nucleus mediated process at a rate of 1.8 ng s-1 from 0.5 mM Co2+ in 0.1 M neural phosphate solution at 1.0 V. Further studies on the potential and electrolyte dependent stability of the Co-Pi suggest that the catalyst undergoes severe corrosion at high overpotential and in non-buffer electrolytes. Current/ Fig.1 (a) Cyclic voltammograms and (b) mass variations vs. potential of Au-coated quartz crystal in 0.1 M potassium phosphate buffer solution (pH 7.0) containing 0.5 mM Co(NO3)2 Chapter 4 deals with the electrochemical deposition of a novel OER catalyst, namely, Co-acetate (Co-Ac) from a neutral acetate electrolyte containing Co2+ ions. Use of acetate solution instead of phosphate avoids the solubility limitations and helps to get thick layer of the catalyst in a short time from concentrated Co2+ solutions. In addition, the Co-Ac is found to be catalytically superior to Co-Pi (Fig. 2a). It is also observed that the Co-Ac catalyst undergoes ion exchange with electrolyte species during electrolysis in phosphate buffer solution, which results in the formation of a hybrid Co-Ac-Pi catalyst (Fig. 2b). The presence of both acetate and phosphate ions in the catalyst and their synergistic catalytic effect enhance the OER activity. Fig.2. (a) Linear sweep voltammograms of Co-Ac in (i) phosphate and (ii) acetate electrolytes, and that of Co-Pi in (iii) acetate and (iv) phosphate electrolytes. (b) SEM image showing the formation of two layers of the catalysts after electrolysis in phosphate solution. In Chapter 5, high OER activity of an electrodeposited amorphous Ir-phosphate (Ir-Pi) is investigated. The catalyst is prepared by the anodic polarization of a carbon paper electrode in neutral phosphate solution containing Ir3+ ions (Fig. 3). The Ir-Pi film deposited on the electrode has Ir and P in an approximate ratio of 1:2 with Ir in an oxidation state higher than +4. Phosphate ions play a major role for both the electrochemical deposition process and its catalytic activity towards OER. The Ir-Pi catalyst is superior to similarly deposited IrO2 and Co-Pi catalysts both in terms of onset potential and current density at any potential in the OER region. Tafel measurements and pH dependence studies identify the formation of a high energy intermediate during oxygen evolution. Fig.3. (a) Cyclic voltammograms during the Ir-Pi deposition and (b) SEM image of Ir-Pi on C. Chapter 6 is on the preparation of a composite of Mn-phosphate (MnOx-Pi) and reduced graphene oxide (rGO) and its utilization as an OER catalyst. The composite is prepared by the simultaneous electrochemical reduction of KMnO4 and graphene oxide (GO) in a phosphate solution (pH 7.0). Various analytical techniques such as TEM, XPS, Raman spectroscopy, etc. confirm the formation of a composite (Fig. 4) and electrochemical studies indicate the favourable role of rGO towards OER. Under identical conditions, MnOx-Pi-rGO gives 6.2 mA cm-2 at 2.05 V vs. RHE whereas it is only 2.9 mA cm-2 for MnOx-Pi alone. However, the catalyst is not very stable during OER which is ascribed to slow oxidation of Mn3+ in the catalyst. Fig.4. (a) Raman spectrum and (b) TEM image of MnOx-Pi-rGO. In Chapter 7, an amorphous Ni-Co-S film is prepared by a potentiodynamic deposition method using thiourea as the sulphur source. The electrodeposit is used as a catalyst for the HER in neutral phosphate solution. The composition of the catalyst and the HER activity are tuned by varying the ratio of concentrations of Ni2+ and Co2+. The bimetallic Ni-Co-S catalyst exhibits better HER activity than both Ni-S and Co-S (Fig. 5a). Under optimized deposition conditions, Ni-Co-S requires just 150 mV for the onset of HER and 10 mA cm-2 is obtained for 280 mV overpotential. The Ni-Co-S shows two different Tafel slopes, indicating two different potential dependent HER mechanisms (Fig. 5b). Presence of two different catalytic sites which contribute selectively in different potential regions is proposed. Fig.5. (a) Linear sweep voltammograms of HER at 1 mV s-1 in 1 M phosphate solutions (pH 7.4) using (i) Ni-S, (ii) Co-S and (c) Ni-Co-S. (b) Tafel plot of Ni-Co-S showing two Tafel slopes. Photoelectrochemical OER using ZnO photoanode and Co-acetate (Co-Ac) cocatalyst is studied in Chapter 8 of the thesis. Randomly oriented crystalline ZnO nanorods are prepared by the electrochemical deposition of Zn(OH)2 followed by heat treatment at 350 ºC in air. Co-Ac is then photochemically deposited onto ZnO nanorods by UV illumination in the presence of neutral acetate buffer solution containing Co2+ ions. The hybrid Co-Ac-ZnO shows higher photoactivity in comparison with bare ZnO towards PEC water oxidation (Fig. 6). Co-Ac acts as a cocatalyst and reduces the charge carrier recombination at the electrode/electrolyte interface. Fig.6. (a) Linear sweep voltammograms of ZnO under (i) dark and (ii) light conditions, and that of Co-Ac-ZnO in (iii) dark and (iv) light in 0.1 M phosphate (pH 7.0) electrolyte. Chapter 9 deals with PEC water oxidation using α-Fe2O3 photoanode and Ir-phosphate (Ir-Pi) cocatalyst. α-Fe2O3 is prepared by direct heating of Fe film in air which in turn is deposited by the electrochemical reduction of Fe2+. Thickness of the film as well as calcination temperature is carefully optimized. In order to further enhance the OER kinetics, Ir-Pi is electrochemically deposited onto α-Fe2O3. Under optimized conditions, Ir-Pi deposited α-Fe2O3 shows around 3 times higher photocurrent than that of bare α-Fe2O3 at 1.23 V vs. RHE (Fig. 7). Ir-Pi acts as a cocatalyst for OER and reduces the photogenerated charge carrier recombination. Fig.7. Photocurrent variation of α-Fe2O3 electrode at 1.23 V vs. RHE for (i) front and (ii) back side illuminations, against Ir-Pi deposition time. The thesis ends with a short summary and future prospectus of studies described in the thesis. The research work presented in the thesis is carried out by the candidate as the part of Ph.D. program. Some of the results have already been published in the literature and some manuscripts are under preparation. A list of publications is included at the end of the thesis. It is anticipated that the studies reported in the thesis will constitute a worthwhile contribution.