The thickness shear mode acoustic wave (TSM) sensor, operated in a flow-through format, has been widely used in bioanalytical research. My research is mainly focused on the study of surface-attached biomolecules and cells using the TSM sensor, including lesions in DNA, conformational change of calmodulin, as well as the properties and attachment of rat aortic smooth muscle cells. Aldehydic apurinic or apyrimidinic sites (AP sites) that lack a nucleobase moiety are one of the most common forms of toxic lesions in DNA. In this work, synthesized oligodeoxyribonucleotides containing one, two, or three abasic sites were hybridized to complementary sequences immobilized on the gold electrode of the TSM device by affinity binding. The influence of AP sites on local base stacking energy and geometry caused a dramatic destabilization of the DNA duplex structure, which was detected by the TSM sensor. The signals detected by TSM correlated well with the thermostability of DNA duplexes in solution. The results indicate that both the number of sites and their localization in the double-stranded structure influence the stability of a 19 b.p. duplex. TSM was also used to detect the binding of ions or peptides to surface-attached calmodulin. The interaction between calmodulin and ions induced an increase in resonant frequency and a decrease in motional resistance. In addition, these signal changes were reversible upon washing with buffer. The response was interpreted as a decrease in surface coupling induced by exposure of hydrophobic domains on the protein, and an increase in the length of calmodulin by approximately 3 Å. In addition, the interaction of the protein with peptide together with calcium ions was detected successfully, despite the relatively low molecular mass of the 2-kDa peptide. In addition, the attachment of smooth muscle cells to various surfaces has been monitored by TSM. These surfaces include laminin, fibronectin and bare gold. The results of these experiments in terms of changes of frequency (fs) and resistance (Rm) were analyzed. The responses of the surface-bound cells to the introduction of various ions, depolarisation events and damage subsequent to exposure to hydrogen peroxide were also observed. Morphological changes in the cells, as confirmed by atomic force microscopy and scanning electron microscopy, are correlated with results from the TSM sensor.

The thickness shear mode acoustic wave (TSM) sensor, operated in a flow-through format, has been widely used in bioanalytical research. My research is mainly focused on the study of surface-attached biomolecules and cells using the TSM sensor, including lesions in DNA, conformational change of calmodulin, as well as the properties and attachment of rat aortic smooth muscle cells. Aldehydic apurinic or apyrimidinic sites (AP sites) that lack a nucleobase moiety are one of the most common forms of toxic lesions in DNA. In this work, synthesized oligodeoxyribonucleotides containing one, two, or three abasic sites were hybridized to complementary sequences immobilized on the gold electrode of the TSM device by affinity binding. The influence of AP sites on local base stacking energy and geometry caused a dramatic destabilization of the DNA duplex structure, which was detected by the TSM sensor. The signals detected by TSM correlated well with the thermostability of DNA duplexes in solution. The results indicate that both the number of sites and their localization in the double-stranded structure influence the stability of a 19 b.p. duplex. TSM was also used to detect the binding of ions or peptides to surface-attached calmodulin. The interaction between calmodulin and ions induced an increase in resonant frequency and a decrease in motional resistance. In addition, these signal changes were reversible upon washing with buffer. The response was interpreted as a decrease in surface coupling induced by exposure of hydrophobic domains on the protein, and an increase in the length of calmodulin by approximately 3 Å. In addition, the interaction of the protein with peptide together with calcium ions was detected successfully, despite the relatively low molecular mass of the 2-kDa peptide. In addition, the attachment of smooth muscle cells to various surfaces has been monitored by TSM. These surfaces include laminin, fibronectin and bare gold. The results of these experiments in terms of changes of frequency (fs) and resistance (Rm) were analyzed. The responses of the surface-bound cells to the introduction of various ions, depolarisation events and damage subsequent to exposure to hydrogen peroxide were also observed. Morphological changes in the cells, as confirmed by atomic force microscopy and scanning electron microscopy, are correlated with results from the TSM sensor.

Cette thèse s’inscrit dans le cadre d’une cotutelle internationale entre l’Université de Bourgogne Franche-Comté en France et l’Université de Sherbrooke au Canada. Elle porte sur le développement d'un biocapteur miniature pour la détection et la quantification de bactéries dans des milieux liquides complexes. La bactérie visée est l’Escherichia coli (E. coli), régulièrement mise en cause dans des épidémies d'infections alimentaires, et parfois meurtrière.La géométrie du biocapteur consiste en une membrane en arséniure de gallium (GaAs) sur laquelle est déposé un film mince piézoélectrique d’oxyde de zinc (ZnO). L'apport du ZnO structuré en couche mince constitue un réel atout pour atteindre de meilleures performances du transducteur piézoélectrique et consécutivement une meilleure sensibilité de détection. Une paire d'électrodes déposée sur le film de ZnO permet de générer sous une tension sinusoïdale une onde acoustique se propageant dans le GaAs, à une fréquence donnée. La face arrière de la membrane, quant à elle, est fonctionnalisée avec une monocouche auto-assemblée (SAM) d'alkanethiols et des anticorps anti-E. coli, conférant la spécificité de la détection. Ainsi, le biocapteur bénéficie à la fois des technologies de microfabrication et de bio-fonctionnalisation du GaAs, déjà validées au sein de l’équipe de recherche, et des propriétés piézoélectriques prometteuses du ZnO, afin d’atteindre potentiellement une détection hautement sensible et spécifique de la bactérie d’intérêt. Le défi consiste à pouvoir détecter et quantifier cette bactérie à de très faibles concentrations dans un échantillon liquide et/ou biologique complexe.Les travaux de recherche ont en partie porté sur les dépôts et caractérisations de couches minces piézoélectriques de ZnO sur des substrats de GaAs. L’effet de l’orientation cristalline du GaAs ainsi que l’utilisation d’une couche intermédiaire de Platine entre le ZnO et le GaAs ont été étudiés par différentes techniques de caractérisation structurale (diffraction des rayons X, spectroscopie Raman, spectrométrie de masse à ionisation secondaire), topographique (microscopie à force atomique), optique (ellipsométrie) et électrique. Après la réalisation des contacts électriques, la membrane en GaAs a été usinée par gravure humide. Une fois fabriqué, le transducteur a été testé en air et en milieu liquide par des mesures électriques, afin de déterminer les fréquences de résonance pour les modes de cisaillement d’épaisseur. Un protocole de bio-fonctionnalisation de surface, validé au sein du laboratoire, a été appliqué à la face arrière du biocapteur pour l’ancrage des SAMs et des anticorps, tout en protégeant la face avant. De plus, les conditions de greffage d’anticorps en termes de concentration utilisée, pH et durée d’incubation, ont été étudiées, afin d’optimiser la capture de bactérie. Par ailleurs, l’impact du pH et de la conductivité de l’échantillon à tester sur la réponse du biocapteur a été déterminé. Les performances du biocapteur ont été évaluées par des tests de détection de la bactérie cible, E. coli, tout en corrélant les mesures électriques avec celles de fluorescence. Des tests de détection ont été réalisés en variant la concentration d’E. coli dans des milieux de complexité croissante. Différents types de contrôles ont été réalisés pour valider les critères de spécificité. En raison de sa petite taille, de son faible coût de fabrication et de sa réponse rapide, le biocapteur proposé pourrait être potentiellement utilisé dans les laboratoires de diagnostic clinique pour la détection d’E. coli. / This thesis was conducted in the frame of an international collaboration between Université de Bourgogne Franche-Comté in France and Université de Sherbrooke in Canada. It addresses the development of a miniaturized biosensor for the detection and quantification of bacteria in complex liquid media. The targeted bacteria is Escherichia coli (E. coli), regularly implicated in outbreaks of foodborne infections, and sometimes fatal.The adopted geometry of the biosensor consists of a gallium arsenide (GaAs) membrane with a thin layer of piezoelectric zinc oxide (ZnO) on its front side. The contribution of ZnO structured in a thin film is a real asset to achieve better performances of the piezoelectric transducer and consecutively a better sensitivity of detection. A pair of electrodes deposited on the ZnO film allows the generation of an acoustic wave propagating in GaAs under a sinusoidal voltage, at a given frequency. The backside of the membrane is functionalized with a self-assembled monolayer (SAM) of alkanethiols and antibodies anti-E. coli, providing the specificity of detection. Thus, the biosensor benefits from the microfabrication and bio-functionalization technologies of GaAs, validated within the research team, and the promising piezoelectric properties of ZnO, to potentially achieve a highly sensitive and specific detection of the bacteria of interest. The challenge is to be able to detect and quantify these bacteria at very low concentrations in a complex liquid and/or biological sample.The research work partly focused on the deposition and characterization of piezoelectric ZnO thin films on GaAs substrates. The effect of the crystalline orientation of GaAs and the use of a titanium / platinum buffer layer between ZnO and GaAs were studied using different structural (X-ray diffraction, Raman spectroscopy, secondary ionization mass spectrometry), topographic (atomic force microscopy), optical (ellipsometry) and electrical characterizations. After the realization of the electrical contacts on top of the ZnO film, the GaAs membrane was micromachined using chemical wet etching. Once fabricated, the transducer was tested in air and liquid medium by electrical measurements, in order to determine the resonance frequencies for thickness shear mode. A protocol for surface bio-functionalization, validated in the laboratory, was applied to the back of the biosensor for anchoring SAMs and antibodies, while protecting the top side. Furthermore, different conditions of antibody grafting such as the concentration, pH and incubation time, were tested to optimize the immunocapture of bacteria. In addition, the impact of the pH and the conductivity of the solution to be tested on the response of the biosensor has been determined. The performances of the biosensor were evaluated by detection tests of the targeted bacteria, E. coli, while correlating electrical measurements with fluorescence microscopy. Detection tests were completed by varying the concentration of E. coli in environments of increasing complexity. Various types of controls were performed to validate the specificity criteria. Thanks to its small size, low cost of fabrication and rapid response, the proposed biosensor has the potential of being applied in clinical diagnostic laboratories for the detection of E. coli.