Aerodynamic devices, such as wings, are used in higher levels of motorsport (Formula-1 etc.) to increase the contact force between the road and tyres (i.e. to generate downforce). This in turn increases the performance envelope of the race car. However the extra downforce increases aerodynamic drag which (apart from when braking) is generally detrimental to lap-times. The drag acts to slow the vehicle, and hinders the effect of available drive power and reduces fuel economy. Wings, in automotive use, are not constrained by the same parameters as aircraft, and thus higher angles of attack can be safely reached, although at a higher cost in drag. Variable geometry aerodynamic devices have been used in many forms of motorsport in the past offering the ability to change the relative values of downforce and drag. These have invariably been banned, generally due to safety reasons. The use of active aerodynamics is currently legal in both Formula SAE (engineering compet ition for university students to design, build and race an open-wheel race car) and production vehicles. A number of passenger car companies are beginning to incorporate active aerodynamic devices in their designs. In this research the effect of ground proximity on the lift, drag and moment coefficients of inverted, two-dimensional aerofoils was investigated. The purpose of the study was to examine the effect ground proximity on aerofoils post stall, in an effort to evaluate the use of active aerodynamics to increase the performance of a race car. The aerofoils were tested at angles of attack ranging from 0° - 135°. The tests were performed at a Reynolds number of 2.16 x 105 based on chord length. Forces were calculated via the use of pressure taps along the centreline of the aerofoils. The RMIT Industrial Wind Tunnel (IWT) was used for the testing. Normally 3m wide and 2m high, an extra contraction was installed and the section was reduced to form a width of 295mm. The wing was mounted between walls to simulate 2-D flow. The IWT was chosen as it would allow enough height to reduce blockage effect caused by the aerofoils when at high angles of incidence. The walls of the tunnel were pressure tapped to allow monitoring of the pressure gradient along the tunnel. The results show a delay in the stall of the aerofoils tested with reduced ground clearance. Two of the aerofoils tested showed a decrease in Cl with decreasing ground clearance; the third showed an increase. The Cd of the aerofoils post-stall decreased with reduced ground clearance. Decreasing ground clearance was found to reduce pitch moment variation of the aerofoils with varied angle of attack. The results were used in a simulation of a typical Formula SAE race car.

Aerodynamic devices, such as wings, are used in higher levels of motorsport (Formula-1 etc.) to increase the contact force between the road and tyres (i.e. to generate downforce). This in turn increases the performance envelope of the race car. However the extra downforce increases aerodynamic drag which (apart from when braking) is generally detrimental to lap-times. The drag acts to slow the vehicle, and hinders the effect of available drive power and reduces fuel economy. Wings, in automotive use, are not constrained by the same parameters as aircraft, and thus higher angles of attack can be safely reached, although at a higher cost in drag. Variable geometry aerodynamic devices have been used in many forms of motorsport in the past offering the ability to change the relative values of downforce and drag. These have invariably been banned, generally due to safety reasons. The use of active aerodynamics is currently legal in both Formula SAE (engineering compet ition for university students to design, build and race an open-wheel race car) and production vehicles. A number of passenger car companies are beginning to incorporate active aerodynamic devices in their designs. In this research the effect of ground proximity on the lift, drag and moment coefficients of inverted, two-dimensional aerofoils was investigated. The purpose of the study was to examine the effect ground proximity on aerofoils post stall, in an effort to evaluate the use of active aerodynamics to increase the performance of a race car. The aerofoils were tested at angles of attack ranging from 0° - 135°. The tests were performed at a Reynolds number of 2.16 x 105 based on chord length. Forces were calculated via the use of pressure taps along the centreline of the aerofoils. The RMIT Industrial Wind Tunnel (IWT) was used for the testing. Normally 3m wide and 2m high, an extra contraction was installed and the section was reduced to form a width of 295mm. The wing was mounted between walls to simulate 2-D flow. The IWT was chosen as it would allow enough height to reduce blockage effect caused by the aerofoils when at high angles of incidence. The walls of the tunnel were pressure tapped to allow monitoring of the pressure gradient along the tunnel. The results show a delay in the stall of the aerofoils tested with reduced ground clearance. Two of the aerofoils tested showed a decrease in Cl with decreasing ground clearance; the third showed an increase. The Cd of the aerofoils post-stall decreased with reduced ground clearance. Decreasing ground clearance was found to reduce pitch moment variation of the aerofoils with varied angle of attack. The results were used in a simulation of a typical Formula SAE race car.

In this diploma thesis active aerodynamic components are designed, specifically brake cooling duct and active automotive wing. Cooling duct prototype and also active regulation controlling electronics including the software were created. Road test was performed to measure the duct parameters. Construction design and the active regulation function of the automotive wing were created. The influence of the wing on aerodynamic characteristics of the car was determined.