The thesis deals with the design and implementation of an Adaptive Flight Control technique for Unmanned Aerial Vehicles (UAVs). The application of UAVs has been increasing exponentially in the last decade both in Military and Civilian fronts. These UAVs fly at very low speeds and Reynolds numbers, have nonlinear coupling, and tend to exhibit time varying characteristics. In addition, due to the variety of missions, they fly in uncertain environments exposing themselves to unpredictable external disturbances. The successful completion of the UAV missions is largely dependent on the accuracy of the control provided by the flight controllers. Thus there is a necessity for accurate and robust flight controllers. These controllers should be able to adapt to the changes in the dynamics due to internal and external changes. From the available literature, it is known that, one of the better suited adaptive controllers is the model based controller. The design and implementation of model based adaptive controller is discussed in the thesis. A critical issue in the design and application of model based control is the online identification of the UAV dynamics from the available sensors using the onboard processing capability. For this, proper instrumentation in terms of sensors and avionics for two platforms developed at UNSW@ADFA is discussed. Using the flight data from the remotely flown platforms, state space identification and fuzzy identification are developed to mimic the UAV dynamics. Real time validations using Hardware in Loop (HIL) simulations show that both the methods are feasible for control. A finer comparison showed that the accuracy of identification using fuzzy systems is better than the state space technique. The flight tests with real time online identification confirmed the feasibility of fuzzy identification for intelligent control. Hence two adaptive controllers based on the fuzzy identification are developed. The first adaptive controller is a hybrid indirect adaptive controller that utilises the model sensitivity in addition to output error for adaptation. The feedback of the model sensitivity function to adapt the parameters of the controller is shown to have beneficial effects, both in terms of convergence and accuracy. HIL simulations applied to the control of roll stabilised pitch autopilot for a typical UAV demonstrate the improvements compared to the direct adaptive controller. Next a novel fuzzy model based inversion controller is presented. The analytical approximate inversion proposed in this thesis does not increase the computational effort. The comparisons of this controller with other controller for a benchmark problem are presented using numerical simulations. The results bring out the superiority of this technique over other techniques. The extension of the analytical inversion based controller for multiple input multiple output problem is presented for the design of roll stabilised pitch autopilot for a UAV. The results of the HIL simulations are discussed for a typical UAV. Finally, flight test results for angle of attack control of one of the UAV platforms at UNSW@ADFA are presented. The flight test results show that the adaptive controller is capable of controlling the UAV suitably in a real environment, demonstrating its robustness characteristics.

This research work provides the development of an Adaptive Flight Control System (AFCS) for autonomous hover of a Rotary-wing Unmanned Aerial Vehicle (RUAV). Due to the complex, nonlinear and time-varying dynamics of the RUAV, indirect adaptive control using the Model Predictive Control (MPC) is utilised. The performance of the MPC mainly depends on the model of the RUAV used for predicting the future behaviour. Due to the complexities associated with the RUAV dynamics, a neural network based black box identification technique is used for modelling the behaviour of the RUAV. Auto-regressive neural network architecture is developed for offline and online modelling purposes. A hybrid modelling technique that exploits the advantages of both the offline and the online models is proposed. In the hybrid modelling technique, the predictions from the offline trained model are corrected by using the error predictions from the online model at every sample time. To reduce the computational time for training the neural networks, a principal component analysis based algorithm that reduces the dimension of the input training data is also proposed. This approach is shown to reduce the computational time significantly. These identification techniques are validated in numerical simulations before flight testing in the Eagle and RMAX helicopter platforms. Using the successfully validated models of the RUAVs, Neural Network based Model Predictive Controller (NN-MPC) is developed taking into account the non-linearity of the RUAVs and constraints into consideration. The parameters of the MPC are chosen to satisfy the performance requirements imposed on the flight controller. The optimisation problem is solved numerically using nonlinear optimisation techniques. The performance of the controller is extensively validated using numerical simulation models before flight testing. The effects of actuator and sensor delays and noises along with the wind gusts are taken into account during these numerical simulations. In addition, the robustness of the controller is validated numerically for possible parameter variations. The numerical simulation results are compared with a base-line PID controller. Finally, the NN-MPCs are flight tested for height control and autonomous hover. For these, SISO as well as multiple SISO controllers are used. The flight tests are conducted in varying weather conditions to validate the utility of the control technique. The NN-MPC in conjunction with the proposed hybrid modelling technique is shown to handle additional disturbances successfully. Extensive flight test results provide justification for the use of the NN-MPC technique as a reliable technique for control of non-linear complex dynamic systems such as RUAVs.