1 |
Acoustic modelling and testing of advanced exhaust system components for automotive enginesAllam, Sabry January 2004 (has links)
The increased use of the diesel engine in the passenger car, truck and bus market is due to high efficiency and lower fuel costs. This growing market share has brought with it several environmental issues for instance soot particle emission. Different technologies to remove the soot have been developed and are normally based on some kind of soot trap. In particular for automobiles the use of diesel particulate traps or filters (DPF:s) based on ceramic monolithic honeycombs are becoming a standard. This new exhaust system component will affect the acoustics and also work as a muffler. To properly design exhaust systems acoustic models for diesel particulate traps are needed. The first part of this thesis considers the modelling of sound transmission and attenuation for traps that consist of narrow channels separated by porous walls. This work has resulted in two new models an approximate 1-D model and a more complete model based on the governing equations for a visco-thermal fluid. Both models are expressed as acoustic 2-ports which makes them suitable for implementation in acoustic software for exhaust systems analysis. The models have been validated by experiments on clean filters at room temperature with flow and the agreement is good. In addition the developed filter models have been used to set up a model for a complete After Treatment Device (ATD) for a passenger car. The unit consisted of a chamber which contained both a diesel trap and a Catalytic Converter (CC). This complete model was also validated by experiments at room temperature. The second part of the thesis focuses on experimental techniques for plane wave decomposition in ducts with flow. Measurements in ducts with flow are difficult since flow noise (turbulence) can strongly influence the data. The difficulties are also evident from the lack of good published in-duct measurement data, e.g., muffler transmission loss data, for Mach-numbers above 0.1-0.2. The first paper in this part of the thesis investigates the effect of different microphone mountings and signal processing techniques for suppressing flow noise. The second paper investigates in particular flow noise suppression techniques in connection with the measurement of acoustic 2-ports. Finally, the third paper suggests a general wave decomposition procedure using microphone arrays and over-determination. This procedure can be used to determine the full plane wave data, e.g., the wave amplitudes and complex wave numbers k+ and k-. The new procedure has been applied to accurately measure the sound radiation from an unflanged pipe with flow. This problem is of interest for correctly determining the radiated power from an engine exhaust outlet. The measured data for the reflection coefficient and end correction have been compared with the theory of Munt [33] and the agreement is excellent. The measurements also produced data for the damping value (imaginary part of the wavenumber) which were compared to a model suggested by Howe [13]. The agreement is good for a normalized boundary layer thickness less than 30-40
|
2 |
Acoustic modelling and testing of advanced exhaust system components for automotive enginesAllam, Sabry January 2004 (has links)
<p>The increased use of the diesel engine in the passenger car, truck and bus market is due to high efficiency and lower fuel costs. This growing market share has brought with it several environmental issues for instance soot particle emission. Different technologies to remove the soot have been developed and are normally based on some kind of soot trap. In particular for automobiles the use of diesel particulate traps or filters (DPF:s) based on ceramic monolithic honeycombs are becoming a standard. This new exhaust system component will affect the acoustics and also work as a muffler. To properly design exhaust systems acoustic models for diesel particulate traps are needed. The first part of this thesis considers the modelling of sound transmission and attenuation for traps that consist of narrow channels separated by porous walls. This work has resulted in two new models an approximate 1-D model and a more complete model based on the governing equations for a visco-thermal fluid. Both models are expressed as acoustic 2-ports which makes them suitable for implementation in acoustic software for exhaust systems analysis. The models have been validated by experiments on clean filters at room temperature with flow and the agreement is good. In addition the developed filter models have been used to set up a model for a complete After Treatment Device (ATD) for a passenger car. The unit consisted of a chamber which contained both a diesel trap and a Catalytic Converter (CC). This complete model was also validated by experiments at room temperature. The second part of the thesis focuses on experimental techniques for plane wave decomposition in ducts with flow. Measurements in ducts with flow are difficult since flow noise (turbulence) can strongly influence the data. The difficulties are also evident from the lack of good published in-duct measurement data, e.g., muffler transmission loss data, for Mach-numbers above 0.1-0.2. The first paper in this part of the thesis investigates the effect of different microphone mountings and signal processing techniques for suppressing flow noise. The second paper investigates in particular flow noise suppression techniques in connection with the measurement of acoustic 2-ports. Finally, the third paper suggests a general wave decomposition procedure using microphone arrays and over-determination. This procedure can be used to determine the full plane wave data, e.g., the wave amplitudes and complex wave numbers k+ and k-. The new procedure has been applied to accurately measure the sound radiation from an unflanged pipe with flow. This problem is of interest for correctly determining the radiated power from an engine exhaust outlet. The measured data for the reflection coefficient and end correction have been compared with the theory of Munt [33] and the agreement is excellent. The measurements also produced data for the damping value (imaginary part of the wavenumber) which were compared to a model suggested by Howe [13]. The agreement is good for a normalized boundary layer thickness less than 30-40</p>
|
Page generated in 0.0627 seconds