Thesis (M. S.)--Aerospace Engineering, Georgia Institute of Technology, 2009. / Committee Chair: Zinn, Ben; Committee Member: Fuller, Thomas; Committee Member: Gaeta, Rick; Committee Member: Jagoda, Jeff; Committee Member: Neumeier, Yedidia

Thesis (M. S.)--Aerospace Engineering, Georgia Institute of Technology, 2010. / Committee Chair: Tim Lieuwen; Committee Member: Jeff Jagoda; Committee Member: Suresh Menon. Part of the SMARTech Electronic Thesis and Dissertation Collection.

Thesis (Ph.D)--Mechanical Engineering, Georgia Institute of Technology, 2009. / Committee Chair: Zinn, Ben; Committee Co-Chair: Jagoda, Jeff; Committee Member: Glezer, Ari; Committee Member: Jeter, Sheldon; Committee Member: Neumeier, Yedidia. Part of the SMARTech Electronic Thesis and Dissertation Collection.

This work concerns the prediction of potentially damaging thermoacoustic oscillations in gas turbine combustion systems by computational means. A framework is laid out to predict numerically the frequency and stability of thermoacoustic oscillations, with focus on the high frequency screech instability of afterburners. A hybrid numerical method is used that includes separate calculations of the mean flow and of the perturbed field due to the acoustic oscillations. This modularity supports the choice of models that are the most appropriate for combustion and for acoustic wave propagation, which are the processes that make up the feedback mechanism that can lead to the establishment of an instability. This gives flexibility, improved accuracy and more insight into the physics of the thermoacoustic system at a potentially reduced computational cost. The mechanism leading to screech involves the formation of vortices induced by acoustic transverse modes at the afterburner flameholder. These vortices trap fresh reactants that burn after a certain time delay, therefore feeding energy into the oscillation. Within a linear approximation, the effect of small amplitude acoustic fluctuations on the flame is studied by perturbing harmonically the transverse velocity at the flameholder lip over a range of frequencies using forced combustion CFD calculations. The response in heat release rate, which is a thermoacoustic source of sound, is represented by a flame transfer function (FTF). It is argued that for the investigation of screech oscillations, this FTF must be multi-dimensional because of the transverse nature of the acoustic oscillation. For fully premixed flames, the main contributor to heat release rate fluctuations is the variation in flame surface area. This information is used to develop a novel flame model that represents the multi-dimensional, frequency dependent response of the flame to velocity perturbations. Compared to FTFs, which require computationally expensive forced calculations, this model has the advantage of providing the frequency dependent flame response as part of the acoustic calculation. After verification and validation of each of the tools used for the acoustic and combustion simulations, this flame model is used in the analysis of a simplified afterburner, where a high frequency, radial and longitudinal resonant mode was computed. Convective modes, which are important in the prediction of the frequency of thermoacoustic oscillations are predicted as a result of the interaction between the acoustic wave and the flame.

State of the art aircraft afterburners employ spray bars to inject fuel and flameholders to stabilize the combustion process. Such afterburner designs significantly increase the length (and thus weight), pressure losses, and observability of the engine. This thesis presents a feasibility study of a compact prime and trigger (PAT) afterburner concept that eliminates the fuel spray bars and flameholders and, thus, eliminates the above-mentioned problems. In this concept, afterburner fuel is injected just upstream or in between the turbine stages. Downstream of the turbine stages, a low power pilot, or trigger , can be used to control the combustion process. The envisioned trigger for the PAT concept is a jet of product gas from ultra-rich hydrocarbon/air combustion that is injected through the afterburner liner. This partial oxidation (POx) gas, which consists mostly of H2, CO, and diluents, rapidly produces radicals and heat that accelerate the autoignition of the primed mixture and, thus, provide an anchor point for the afterburner combustion process. The objective of this research was to demonstrate the feasibility of the PAT concept by showing that (1) combustion of fuel injected within or upstream of turbine stages can occur only downstream of the turbine stages, and (2) the combustion zone is compact, stable and efficient. This was accomplished using two experimental facilities, a developed theoretical model, and Chemkin simulations. The first facility, termed the Afterburner Facility (AF), simulated the bulk flow temperature, velocity and O2 content through a turbojet combustor, turbine stage and afterburner. The second facility, termed the Propane Autoignition Combustor (PAC), was essentially a scaled-down, simplified version of the AF. The developed model was used to predict and interpret the AF results and to study the feasibility of the PAT concept at pressures outside the AF operating range. Finally, the Chemkin simulations were used to study the effect of several POx gas compositions on the afterburner combustion process.

Gas turbine reheat thrust augmenters known as afterburners are used to provide additional thrust during emergencies, take off, combat, and in supersonic flight of high-performance aircrafts. During the course of reheat development, the most persistent trouble has been the onset of high frequency combustion instability, also known as screech, invariably followed by rapid mechanical failure. The coupling of acoustic pressure upstream of the flame stabilizer with in-phase heat-release downstream, results in combustion instability by which the amplitude at various resonant modes — longitudinal (buzz — low frequency), tangential or radial (screech — high frequency) – amplifies leading to deterioration of the afterburner components. Various researchers in early 1950s have performed extensive testing on straight jet afterburners, to identify screech frequencies. Theoretical and experimental work at test rig level has been reported in the case of buzz to validate the heat release combustion models. In this work, focus is given to study the high frequency tangential combustion instability by vibro-acoustic software and the tests are conducted on the scaled bypass flow afterburner for confirmation of predicted screech frequencies. The wave equation for the afterburner is solved taking the appropriate geometry of the afterburner and taking into account the factors affecting the stability. Nozzle of the afterburner is taken into account by using the nozzle admittance condition derived for a choked nozzle. Screech liner admittance boundary condition is imposed and the effect on acoustic attenuation is studied. A new combustion model has been proposed for obtaining the heat release rate response function to acoustic oscillations. Acoustic wave – flame interactions involve unsteady kinetic, fluid mechanic and acoustic processes over a large range of time scales. Three types of flow disturbances exist such as : vortical, entropy, and acoustic. In a homogeneous, uniform flow, these three disturbance modes propagate independently in the linear approximation. Unsteady heat release also generates entropy and vorticity disturbances. Since flow is not accelerated in the region of uniform area duct, vortical and entropy disturbances are treated as in significant, as these disturbances are convected out into atmosphere like an open-ended tube, but these are considered in deriving the nozzle admittance condition. Heat release fluctuations that arise due to fluctuating pressure and temperature are taken into consideration. The aim is to provide results on how flames respond to pressure disturbances of different amplitudes and characterised by different length scales. The development of the theory is based on large activation energy asymptotics. One-dimensional conservation equations are used for obtaining the response function for the heat release rate assuming the laminar flamelet model to be valid. The estimates are compared with the published data and deviations are discussed. The normalized acoustic pressure variation in the afterburner is predicted using the models discussed earlier to provide an indication of the resonant modes of the pressure oscillations and the amplification and attenuation of oscillations caused by the various processes. Similar frequency spectrum is also obtained experimentally using a test rig for a range of inlet mean pressures and temperatures with combustion and core and bypass flows simulated, for confirmation of predicted results. Without the heat source only longitudinal acoustic modes are found to be excited in the afterburner test section. With heat release, three additional tangential modes are excited. By the use of eight probes in the circumferential cross section of afterburner it was possible to identify the tangential modes by their respective phase shift in the experiments. Comparison of normalized acoustic pressure and phase with and without the incorporation of perforate liner is made to study the effectiveness of the screech liner in attenuating the amplitude of screech modes. By the analysis, conclusion is drawn about modes that get effectively attenuated with the presence of perforate liner. Parametric study of screech liner porosity factor of 1.5 % has not shown appreciable attenuation. Whereas with 2.5 % porosity significant attenuation is noticed, but with 4 % porosity, the gain is very minimal. Hence, the perforate screech liner with the porosity of 2.5 % is finalized. From the rig runs, first pure screech tangential mode and second screech coupled tangential modes are captured. The theoretical frequencies for first and second tangential modes with their phases are comparable with experimental results. Though third tangential mode is predicted, it was not excited in the experiments. There was certain level of deviation in the prediction of these frequencies, when compared to the experimentally obtained values. For this test section of length to diameter ratio of 5, no radial modes are encountered both in the analysis and experiments in the frequency range of interest. In summary, an acoustic model has been developed for the afterburner combustor, taking into account the combustion response, the screech liner and the nozzle to study the acoustic instability of the afterburner. The model has been validated experimentally for screech frequencies using a model test rig and the results have given sufficient confidence to apply the model for full scale afterburners as a predictive design tool.

This thesis focuses on experimentally measuring the response of varying dilatation ratio bluff body flames under harmonic excitation. Such flames are often encountered in jet engine afterburners and are susceptible to combustion instabilities. Previous work has been done modeling such flames, however, only limited experimental data has been obtained at these conditions and is the motivation for this thesis. The focus of this work is to measure the transfer function of longitudinally forced, varying dilatation ratio bluff body flames. The transfer function is obtained by measuring flame position and flame luminosity fluctuations at the forcing frequency. Specifically, the amplitude and phase of the fluctuations are characterized as a function of flow velocity, axial location, and perturbation amplitude. These measurements are also compared to available theoretical predictions, showing that qualitative measured trends are consistent with theory. In addition, a detailed quantitative comparison is performed at one condition, showing good agreement between predictions and measurements in the near and mid-field of the flame response. However, agreement is not obtained in the far-field, indicating that continued theoretical work is needed to understand the flame response characteristics in this region.

In current afterburners combustion is stabilized by the high temperature, recirculating region behind bluff body flame holders, such as V-gutters. Blocking the high speed flow with bluff bodies causes a significant pressure drop, and heating the flame holder by the hot combustion product causes a thermal signature, which is a critical problem in a military jet. To reduce these problems, ignition methods using a high frequency (HF) spark discharge, or a radical jet generator (RJG) were developed. The HF discharge ignited and stabilized a flame successfully in a premixed methane-air flow. The electrical power consumption was very small compared to the combustion heat release, as long as the operating velocity was relatively low. However, a theoretical study showed that the ratio of the electrical power consumption to the heat generation by the stabilized flame increases rapidly with increasing flow velocity. For flame stabilization in a high velocity flow, the developed RJG showed much better performance than direct exposure to a plasma. The present study investigated the characteristics of a radical jet produced in a RJG and injected into a main combustor. The limits of flame stabilization by this jet was measured experimentally, and compared to those of bluff body flame holders. The flame holding performance of the radical jet was also experimentally compared to that of a thermal jet. The effect of radicals on flame stabilization was examined using CHEMKIN, and the limit of flame stabilization by the radical jet was estimated for a simple flow configuration using an approximate solution. The results suggest that the reduction of local spontaneous ignition delay time by active species in the radical jet and the longer length of a typical radical jet compared to the dimension of the recirculation zone behind a bluff body increases the maximum velocity at which a flame can be stabilized.

A variety of methods exist to remove volatile organic compound (VOC) air pollutants from contaminated gas streams. As regulatory and public opinion pressures increase, companies are searching for more effective methods to control these emissions. This document is intended as a guide to help determine if existing systems are adequate and to provide additional information to improve the efficiency of the systems. It explores conventional methods of controlling VOC emissions, as well as innovative technologies including membrane separation, plasma destruction, and ozone catalytic oxidation. The conventional technologies covered include condensation, adsorption, absorption (or scrubbing), thermal incineration, flaring, catalytic incineration, and biofiltration. Each chapter includes a description of the technology, a discussion of the types of systems available, notes on the design of the system, economic estimates, an explanation of potential problems, and a list of considerations for installation and maintenance concerns. The final chapter is dedicated to the preparation and characterization of metal catalysts which were developed to improve the reaction rate of VOCs using ozone as an oxidant. / Ph. D.