Fungal contamination of buildings poses numerous challenges to researchers, building owners and occupants. Public health agencies promote prevention and remediation of mold and water damage, but lack sensitive methods to detect hidden mold growth and a complete understanding of the biological mechanisms that make occupying moldy buildings a hazard. The wide spread use of the fire retardant antimony trioxide (Sb2O3) on building materials and furnishings makes it inevitable that mold growth on treated materials will occur in some buildings with water damage. Several authors have speculation that microbial growth on materials treated with antimony trioxide could mobilize antimony through a volatile intermediate, trimethylstibine. The purpose of this study was to determine if fungal growth on a commonly used building material that contains antimony trioxide, fiberglass ductboard, results in the mobilization and release of antimony compounds. Additionally, CO2 generation rates were determined during fungal growth on fiberglass ductboard and gypsum wallboard. Results demonstrated a significant reduction of antimony concentration in fiberglass ductboard after fungal growth had occurred. Antimony emission rates and resulting concentrations of antimony oxide aerosols were estimated using an indoor mass balance mathematical model. Concentrations of CO2 were also modeled within a wall cavity and static HVAC ducts to determine if fungal growth could elevate CO2 levels above ambient concentrations. Although volatile phase antimony was not detected in chamber experiments, probably due to rapid oxidation and high humidity, mobilization of antimony trioxide from fiberglass ductboard components was demonstrated in several experiments. Indoor Air modeling of a residence suggest that concentrations of antimony could, under worst case conditions, exceed the reference concentration (RfC) of antimony trioxide by 10 to 1,000 times. These results suggest that biomethylation and mobilization of antimony by mold growth on building materials could result in elevated occupant exposures to antimony compounds. Antimony is a known respiratory irritant that can be similar to arsenic in its toxicity. Modeling results also suggest that elevated carbon dioxide concentrations due to fungal metabolic respiration are variable and dependent on environmental conditions. Measuring elevated carbon dioxide concentrations to detect hidden fungal growth was determined to not be a predictive assessment tool.

This study was directed at the pyrotechnic time delay compositions that are used in detonator assemblies. The objectives were to: --Investigate effective alternatives for the barium and lead-based oxidants currently used, maintaining the use of silicon as fuel --Develop easy to use, realistic measurement techniques for burn rates and shock tube ignitability --Determine the variables that affect burn rate, and --Evaluate alternative processing routes to facilitate intimate mixing of the component powders. Lead chromate and copper antimonite were found to be suitable oxidants for silicon in time delay compositions. They were ignitable by shock tubing, a relatively weak ignition source. The measured burn speeds for these systems showed a bimodal dependence on stoichiometry. Measured burn rates varied between 6-28 mm/s. Lead chromate is potentially a suitable alternative to the oxidant currently used in the medium burn rate commercial composition. It burns faster than copper antimonite. The latter is potentially a suitable replacement oxidant for the slow and medium compositions. Antimony trioxide-based compositions exhibited unreliable performance with respect to ignition with shock tubing. The addition of aluminium powder or fumed silica was found to reduce the burn rate. Increasing the silicon particle size (<3,5<font face="symbol">m</font>m) also decreased the burn speed for copper antimonite and lead chromate compositions. Addition of fumed silica improved the flow properties of the lead chromate, copper antimonite and antimony trioxide powders allowing for easier mixing. The silicon powder was found to react violently with water in alkaline solutions. This makes particle dispersion in a wet-mixing process problematic. / Dissertation (MEng (Chemical Engineering))--University of Pretoria, 2006. / Chemical Engineering / unrestricted

Antimony trioxide (Sb203) and halogenated additives are used together in flameretarded formulations due to their synergistic retardant properties. A study has been made to determine the effects of adding different grades of Sb203 (dSD particle sizes 0.11 um, 0.52um and 1.31 um) into ABS polymer either alone or with commercial brominated materials (BTBPE, TBBA, DBDPO) and an experimental bromine grade (sDBDPO). The Sb20 3 was added at 4wt% loadings and the bromines at 20wt% loadings. The results consider the influence of the additives on processing, mechanical, morphological and flame retardant properties. All compounds were produced using a twin-screw co-rotating extruder and then an injection moulder was used to mould notched impact (falling weight testing), flexural, LOI and UL-94 flame test bars. Samples of all the compounded formulations were titrated to determine Sb20 3 and Br contents. Fracture surface, morphology, size and dispersion analysis was carried out using both SEM and TEM equipment. Osmium tetroxide (OS04) staining was used to determine relative locations of filler particles and polybutadiene phase. Additions of the different antimony trioxide grades showed that the 0.52um and 1.31 um grades lowered impact energy absorption (-25 to -30%) when added at 4wt% loading. The use of a sub-micron size grade (0.1 um) did not significantly lower impact properties (-3%) and had similarly small effects on the flexural modulus and flexural strength. Additions of the brominated materials had much greater effects causing large reductions in impact properties (-20 to :70%). The presence of the bromines generally increased flexural modulus and lowered flexural strength with the exception of TB BA, which increased both modulus and strength. Compounds containing both 1.31 um Sb203 and bromines suffered a further reduction in impact energies, with the bromine properties dominating. Using the 0.1 um Sb20 3 grade again improved impact and flexural properties compared to the 1.31 um grade. The 0.1 um grade resulted in improvements in fire resistance as measured by the UL-94 properties when used with all bromine grades.