<p>This study has been triggered by the fact that stainless steel is being increasingly used in new applications, where possible environmental effects may be a matter of concern. When stainless steel is exposed to a given environment, a key issue is the release of small amounts of the main alloying elements iron, chromium, nickel and molybdenum. Published release rate data of these elements turned out to be sparse. Furthermore, only little was known about the role of different parameters that may affect the release rate, such as degree of alloying, exposure time and surface finish. Hence, the aim of this study was to develop methodological means and to provide accurate metal release rates of alloying constituents from different grades of stainless steels- austenitic, ferritic and duplex- when exposed to selected environments: artificial rain and synthetic body fluids. The results and discussion have been summarised in this thesis by formulating and answering ten questions, all believed to be crucial for the understanding of possible environmental effects of stainless steels.</p><p>Some common conclusions could be drawn, independent of stainless steel grade and exposure condition. Iron was always preferentially released, and the release rates of chromium, nickel and molybdenum (when measured) were significantly lower than of iron, also when considering the bulk proportion of these elements. The release rate of all elements was initially high and decreased with exposure time, mainly because of an observed enrichment of chromium in the passive film formed.</p><p>The release rates of iron (2 μgcm^-2week^-1) and nickel (0.08 μgcm-²week-¹) from stainless steel from grades 304 and 316 exposed to artificial rain were much lower than corresponding rates for the pure metals (750 μgcm-²week^-1 released Fe and 15 μgcm^-2week^-1 released Ni), whereas chromium exhibited similar release rates from stainless steel and the pure metal (0.1 μgcm^-2week^-1). This implies that the common procedure to calculate release rates, based on the pure metals and the nominal steel composition, significantly overestimates release rates of iron and nickel from stainless steel, but not of chromium.</p><p>Total release rates from seven stainless steel grades in synthetic body fluid were found to decrease with increasing alloy content in the following release rate order: grade 409 >> grade 430 > grades 316L ≈ 201 ≈ 2205 ≈ 304 > grade 310. The release rate was highly sensitive to pH of the synthetic body fluid but only slightly sensitive to stainless steel surface finish.</p>

This study has been triggered by the fact that stainless steel is being increasingly used in new applications, where possible environmental effects may be a matter of concern. When stainless steel is exposed to a given environment, a key issue is the release of small amounts of the main alloying elements iron, chromium, nickel and molybdenum. Published release rate data of these elements turned out to be sparse. Furthermore, only little was known about the role of different parameters that may affect the release rate, such as degree of alloying, exposure time and surface finish. Hence, the aim of this study was to develop methodological means and to provide accurate metal release rates of alloying constituents from different grades of stainless steels- austenitic, ferritic and duplex- when exposed to selected environments: artificial rain and synthetic body fluids. The results and discussion have been summarised in this thesis by formulating and answering ten questions, all believed to be crucial for the understanding of possible environmental effects of stainless steels. Some common conclusions could be drawn, independent of stainless steel grade and exposure condition. Iron was always preferentially released, and the release rates of chromium, nickel and molybdenum (when measured) were significantly lower than of iron, also when considering the bulk proportion of these elements. The release rate of all elements was initially high and decreased with exposure time, mainly because of an observed enrichment of chromium in the passive film formed. The release rates of iron (2 μgcm-2week-1) and nickel (0.08 μgcm-2week-1) from stainless steel from grades 304 and 316 exposed to artificial rain were much lower than corresponding rates for the pure metals (750 μgcm-2week-1 released Fe and 15 μgcm-2week-1 released Ni), whereas chromium exhibited similar release rates from stainless steel and the pure metal (0.1 μgcm-2week-1). This implies that the common procedure to calculate release rates, based on the pure metals and the nominal steel composition, significantly overestimates release rates of iron and nickel from stainless steel, but not of chromium. Total release rates from seven stainless steel grades in synthetic body fluid were found to decrease with increasing alloy content in the following release rate order: grade 409 &gt;&gt; grade 430 &gt; grades 316L ≈ 201 ≈ 2205 ≈ 304 &gt; grade 310. The release rate was highly sensitive to pH of the synthetic body fluid but only slightly sensitive to stainless steel surface finish. / QC 20120217

With increasing environmental awareness, the desire to protect human beings and the environment from adverse effects induced by dispersed metals has become an issue of great concern and interest. New policies, such as REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) within the European Community, have been implemented to reduce hazards posed by the use of chemicals on producers and downstream users. The generation of exposure assessment data and relevant test procedures able to simulate realistic scenarios are essential in such legislative actions. This doctoral study was initiated to fill knowledge gaps related to the metal release process of stainless steels. A wide range of stainless steel grades, fourteen in total, were investigated. They cover a very broad range of applications, and the focus in the thesis was to simulate a few selected exposure scenarios: precipitation, the human body and food intake. Comparisons were made between metal release from stainless steel alloys and the pure metals that constitute each stainless steel in order to explore the differences between alloys and pure metals, and to provide quantitative data on metal release rates of different alloy constituents. Because of similar surface properties between stainless steel and pure chromium, this metal exhibits similar release rates, whereas iron and nickel exhibit significantly lower release rates as alloy components than as pure metals. Detailed studies were also performed to elucidate possible relations between metal release and steel surface properties. Key parameters turned out to be chromium enrichment of the self-passivating surface film, surface roughness, the electrochemically active surface area and the microstructure of the steel substrate. The degree of metal release increased with decreasing chromium content in the surface oxide, increasing surface roughness, and increasing presence of inhomogeneities in the bulk matrix. More detailed studies were initiated to possibly correlate the nucleation of metastable pits and the extent of metal release. Evidence was given that metastable pits exist even when the stainless steel is passive, and may cause extremely short-lived bursts of released metal before the surface film repassivates again. / QC 20100810

This dissertation is focused to modeling of the rainfall in laboratory conditions by the rainfall simulator invented in VUT Brno. Results of the measuring are compared with measured values of the original rainfall simulator located in VVU VSH VUT in Brno by the Kninicky village in 1976-1980. Dissertation verifies rightness of substituting the natural rain with the rainfall simulator on bare soil in the original location, kinetic energy of the rain drops is substituted with the energy gained from the weight of the drops - the flow. Generally the dissertation determines the possibilities of the rainfall simulator's current location.