Technology replaces newer technology with improved efficiency. Solar technology is going to draw out a new life to make a green change in the terms of energy. As a result energy from the sunlight is being changed into electric energy by using solar cell. But still its efficiency could not be able to make a sense as a depending energy technology. In order to look up the solution, solar technology is changing rapidly to get maximum output. To take up this new challenge solar technology is trying to change its building component that are used to make solar cell, for example solar cell material, bypass diode system, blocking diode system etc.   Now-a-days, solar energy system is designed as a hybrid system that can make electricity and hot water at the same time. In the hybrid solar system, photovoltaic and solar thermal systems are integrated at the same system and as a result heat and electricity are produced simultaneously at the same area. Solar cells are attached with both top and the bottom side of the module and the collectors are set up inside the module. By using collector inside the module, rejected heat from the solar cell is absorbed by the water that flows through the collectors. But a problem arises at the midday or after midday because the reflector of this system cannot reflect sunlight properly on the bottom side of the module. That’s why shading is occurred on the bottom side which reduce the total electrical output of this system.   To work out this shading problem, a bypass diode is connected in parallel with the group of solar cells. Schottky diodes are being used as bypass diodes inside in the most of the solar cells. Schottky diode forward voltage drop is almost 0.45 Volt which is an important cause of reducing the output power as well as the efficiency of this hybrid system. To solve this problem, new lossless diode is attached inside the hybrid solar system instead of schottky diode which can work with a very low forward voltage drop roughly 50mV at 10amp.   To make a comparison between the performance of PVT system with the schottky diode and the new lossless diode, many data has been collected from the outdoor test. After getting the output result, it is clear that the output power and efficiency is going to be changed for using the new lossless diode. For using the lossless diode, the efficiency of the bottom side of the module was increased by 0.31 %.

The usage of conventional energy applications generates disproportionate emissions of greenhouse gases and the consumption of part of the energy resources available in the world. It has become an important problem which has serious effects on the climatic change. Therefore, it is crucial to reduce these emissions as much as possible. To be able to achieve this, renewable energy technologies must be used instead of conventional energy applications. Solar Photovoltaic (PV) technologies do not release greenhouse gas emissions directly and can save more than 30 million tonnes of carbon per exajoule of electricity generated relative to a natural gas turbine running at 45% efficiency. Shadowing is one of the most important aspects that affects the performance of PV systems. Consequently, many investigations through this topic are being done in order to develop new technologies which mitigate the impact of shadowing during PV production. In order to minimise the impact of shadowing it is desired to be able to predict the performance of a system with PV-modules during shadowing. In this thesis a simulation program for calculating the IV-curve for series connected PV-modules during partial shadowing has been developed and experimentally validated. PV systems modelling and simulation in LTspice environment has been presented and validated by means of a comparative analysis with the experimental results obtained in a set of tests performed in the laboratory of Gävle University. Experimental measurements were carried out in two groups. The first group corresponds with the experiments done in the string of six modules with bypass diodes while the measurements of the second group have been performed on a single PV module at HIG University. The simulation results of both groups demonstrated a remarkable agreement with the experimental data, which means that the model designed at LTspice supposes a very useful tool that can be used to study the performance of PV systems. This tool contributes to the investigations in this topic and it aims to benefit future installations providing a better knowledge of the shading problem. The master’s thesis shows an in-depth description of the required method to design a PV cell, a PV module and a PV array using LTspice IV and the input parameters as well as the needed tests to adjust the models. Moreover, it has been carried out a pedagogical study describing the effect that different shadow configurations have in the performance of solar cells. This study facilitates the understanding of the performance of PV modules under different shadowing effects. Lastly, it has also been discussed the benefits of installing some newer technologies, like DC-DC optimizers or module inverters, to mitigate the shadowing effects. The main conclusion about this topic has been that although most of the times the output power will be increased with the use of optimizers sometimes the optimizer does not present any benefits.

This thesis deals with usage of bypass diodes in photovoltaic panels. Familiarize us with principles of photovoltaic modules and functions, their electrical characteristics and features. The central objective of this work is description of influence of bypass diodes on particularly shading photovoltaic panels and its volt-ampere characteristics. By the help of created software in Agilent VEE 8.0 simulate the shading panel and compare with real measurement.

Solar Photovoltaics (PV) is one of the most promising renewable energy technologies for mitigating the effect of climate change. Reliability of PV modules directly impacts the Levelized Cost of Energy (LCOE), which is a metric for cost competitiveness of any energy technology. Further reduction in LCOE of PV through assured long term reliability is necessary in order to facilitate widespread use of solar energy without the need for subsidies. This dissertation is focused on frameworks for assessing reliability of bypass diodes in PV modules. Bypass diodes are critical components in PV modules that provide protection against shading. Failure of bypass diode in short circuit results in reducing the PV module power by one third, while diode failure in open circuit leaves the module susceptible for extreme hotspot heating and potentially fire hazard. PV modules, along with the bypass diodes are expected to last at least 25 years in field. The various failure mechanisms in bypass diodes such as thermal runaway, high temperature forward bias operation and thermal cycling are discussed. Operation of bypass diode under shading is modeled and method for calculating the module I-V curve under any shading scenario is presented. Frameworks for estimating the diode temperature in field deployed modules based on Typical Meteorological Year (TMY) data are developed. Model for predicting the susceptibility of bypass diodes for thermal runaway is presented. Diode wear out due to High Temperature Forward Bias (HTFB) operation and Thermal Cycling (TC) is studied under custom designed accelerated tests. Overall, this dissertation is an effort towards estimating the lifetime of bypass diodes in field deployed modules, and therefore, reducing the uncertainty in long term reliability of PV modules.

<p dir="ltr">This thesis explores the modeling and analysis of half-cut photovoltaic (PV) modules equipped with bypass diodes under various shading conditions. As solar energy becomes increasingly vital in the global energy landscape, understanding the impact of shading on PV system performance is crucial. Shading, whether from environmental factors like trees and clouds or from elements like buildings, chimneys, and wires, significantly affects the performance and longevity of solar panels. The research recreates various shading conditions on six monocrystalline residential PV panels, each equipped with 120 half-cut cells and three bypass diodes to collect a rich dataset using a Fluke SMFT-1000 I-V Curve Tracer. The I-V curves obtained from these tests were used to refine a simulation model for half-cut PV modules with bypass diodes developed in Simulink, which incorporates an equivalent circuit using the eight-parameter model of a PV cell. The Simulink model's optimization involved fine-tuning parameters such as photo-generated current (Iph), series resistance (Rs), shunt resistance (Rp), and temperature coefficients to closely match measured data. To validate the model’s applicability, the model was tested on PV panels from different manufacturers. Key findings demonstrate that half-cut technology significantly reduces power losses compared to conventional PV modules, particularly under partial shading conditions. The integration of bypass diodes further enhances performance by preventing hotspot formation and allowing unshaded portions of the panel to continue generating power. This study also briefly describes the existing solutions (microinverter, DC optimizer, global MPPT) for residential sites with severe shading.</p>

For a PV plant it is of fundamental importance that the operation of the PV modules is free from faults or at least that the faults can be detected early, to ensure efficient electricity production. Some defects such as cracks can be seen in visible light while microcracks and damage to the silicon material can only be seen through special lighting. This study focuses on the most common defects in photovoltaic (PV) systems. Compare the infrared (IR) technology with the new ultraviolet (UV) fluorescence image technique for PV characterization, based on their accuracy and uncertainty factors under an experimental field investigation. In this study, first a literature study was conducted to the most common defects in PV system and their impact on electricity generation. Then a simulation model of a PV system was created in PVsyst and exported to Microsoft Excel which was used to evaluate how different defects at different stages of the PV cell's life cycle impact electricity generation, performance parameters and economic exchange. Furthermore, experiments with UV and IR was implemented at a PV system located in Dalarna and some PV modules at MDH. It was conducted that occurrence of snail tracks, delamination and hot spots in combination with bypass failures and non-functioning cell will affect the economic profitability in the long run and the payback time will increase since their impacts on electricity generation and performance parameters are huge. The worst case is when PV modules are affected by the fault in bypass diode and non-functioning cell which result to a payback time longer than the module's lifetime and huge amount electricity losses in different bypass diodes configurations. Since UV and IR are two different methods that are performed in two different ways, different errors occurred during the measurements. The biggest external factor was the weather that determined if the experiment could be implemented. The IR method gave decent results and was quicker to use, but the UV method highlighted some defect which could not be seen with the IR technology.