No description available.

The behaviour of limited subassemblages with flexible beans and semi-rigid beam to column connections was studied using a computer program in which the finite element method was employed in a non-linear analysis which accounts for the presence of semi-rigid connections and the inelastic behaviour of frames. The program accounts for many other factors such as initial imperfections and residual stresses. The theoretical background to the present computer program has been presented along with the program layout. The program was used to simulate some of the experimental results obtained from tests on rigidly and flexibly connected frames with different combinations of beam and column loads. The analytical results were found to compare reasonably well with the experimental results. The program was also used to simulate a series of I-shaped subassemblages that were tested at the University of Sheffield. Comparisons were made between the analytical and experimental results characterized by the maximum loads, load-deflection curves and load- moment curves. Good agreement was obtained between the analytical and the experimental load-deflection curves for all of the cases considered. The general trends of the measured and calculated load- moment curves for most cases were found to be comparable. The recommendations given in B35950 for the design of columns in simple construction were applied to all cases in the last series and were found unconservative in the cases of balanced loading and conservative in the cases of unbalanced loads. A limited parametric study was conducted to study the effects of semi-rigid joints, bean flexibility and type of loading. In this study, an I-shaped subassemblage was analysed for different load types and different types of beam to column connections. A substantial effect was recognized due to the presence of semi-rigid connections whether or not a beam load was applied. Beam flexibility was also seen to affect the carrying capacity of the subassemblage under the action of column load only although this effect was less noticeable than that of the connection flexibility. The presence of beam load was found to result in an unexpected interaction curve which relates the total force in the column to the moment that is transmitted to the column's end. An almost linear relationship with negative gradient seems to exist between the column and beam loads. It is pointed out that all the findings of the present study are based on the range of cases considered in the parametric study but it is suggested that they serve as indicators to the behaviour of any the subassemblage under axial load oniy or axial load combined with beam loads. A few recommendations for future work are presented.

As estruturas tubulares, muitas vezes, têm sua aplicação restrita a construções onde a concepção arquitetônica determina o seu uso, no entanto há algumas vantagens do ponto de vista estrutural que podem justificar a sua aplicação. A reduzida área exposta ao fogo e aos ambientes agressivos, boa resistência a compressão axial com baixa tendência ao desenvolvimento de instabilidades localizadas, são algumas das vantagens da utilização destas estruturas. O objetivo principal deste trabalho é analisar numericamente o comportamento da ligação entre viga de seção I com coluna tubular circular, para tanto são consideradas configurações usuais de ligação com anéis externos transversais e chapa de alma. É ainda objetivo trazer um panorama das estruturas tubulares em geral, com o desenvolvimento histórico das pesquisas, e principalmente estabelecer uma compilação dos procedimentos analíticos de cálculo e classificação apresentados pelas normas Eurocode 3 e ANSI/AISC. A análise numérica foi realizada por meio dos pacotes comerciais TRUEGRID® e ANSYS®, os quais aplicam o método dos elementos finitos. Foram empregados modelos que consideram as características mecânicas do aço, como plastificação e encruamento, e ainda as não-linearidades geométricas e de contato. Os resultados numéricos apresentaram coerência razoável com os modelos analíticos normativos. Foi possível o conhecimento do comportamento M-\'fi\' (momento-rotação) das ligações, bem como a determinação dos parâmetros que caracterizam tal relação, como resistência, rigidez inicial e ductilidade. Os estudos comprovaram a eficácia dos anéis externos na distribuição dos esforços oriundos do engastamento parcial da viga, fazendo com que a coluna não seja comprometida. / The application of tubular structures is usually restricted to constructions on which the architectural conception demands them. However, there are also several structural advantages which justify their usage, such as a) reduced exposed area concerning fire and agressive environments; b) high axial compression resistance; c) high local buckling resistance. The aim of this work is the numerical analysis on the behavior of the I beam-circular hollow column connection, usually constituted by an external ring with single plate. It is presented a general view about the researchers development over the years on tubular structures focusing the compilation of the analytical design procedures and Eurocode 3 and ANSI/AISC classification as well. Finite element method softwares TRUEGRID and ANSYS are used for the numerical analysis in order to consider steel mechanical properties such as yielding, hardening and also geometric and contact nonlinearities. Numerical results present good agreement to codes\' analytical models. Analysis lead to understanding the connection\'s moment-rotation behavior and some of its parameters such as resistance, initial stiffness and ductility. It is shown external rings significantlly improve the semi-rigid connections stress distribution at the columns face.

Flat slab-column connections are common elements in reinforced concrete (RC) structures such as parking garages. In cold weather regions, these structures are exposed to de-icing salts and aggressive environments. Using fiber reinforced polymer (FRP) bars instead of steel in such structures will overcome the corrosion problems associated with steel reinforcement. However, the available literature shows few studies to evaluate the behaviour of FRP-RC interior slab-column connections tested mainly under concentric loads, which seldom occurs in a real building. The main objectives of this research are to deal with this gap by investigating the behaviour of full-scale glass (G) FRP-RC interior slab-column connections subjected to eccentric load and to provide design recommendations for such type of connections. This study consisted of two phases, experimental and analytical. The experimental phase included the construction and testing of ten full-scale interior slab-column connections. The parameters investigated in the experimental phase were flexural reinforcement ratio, concrete compressive strength, type of the reinforcement, moment-to-shear ratio and the spacing between the shear stud reinforcement. Test results revealed that increasing the GFRP reinforcement ratio or the concrete strength increased the connection capacity. Moreover, compared to the control steel-RC specimen, the GFRP-RC connection with similar reinforcement rigidity showed comparable capacity and deflection at failure. Also, increasing the moment-to-shear ratio resulted in a reduction in the vertical load capacity, while using the shear stud reinforcement enhanced the strength up to 23%. In the analytical phase, a 3-D finite element model (FEM) was constructed using specialized software. The constructed FEM was able to predict the experimental results within a reasonable accuracy. The verified FEM was then used to conduct a parametric study to evaluate the effects of perimeter-to-depth ratio, column aspect ratio, slab thickness and a wide range of flexural reinforcement ratio. The numerical results showed that increasing the reinforcement ratio increased the connection capacity. In addition, increasing the perimeter-to-depth ratio and slab thickness reduced the punching shear stresses at failure, while, the effect of the column rectangularity diminished for a ratio greater than three. Moreover, the results showed prominent agreement with the experimental results from literature. / October 2015

As estruturas tubulares, muitas vezes, têm sua aplicação restrita a construções onde a concepção arquitetônica determina o seu uso, no entanto há algumas vantagens do ponto de vista estrutural que podem justificar a sua aplicação. A reduzida área exposta ao fogo e aos ambientes agressivos, boa resistência a compressão axial com baixa tendência ao desenvolvimento de instabilidades localizadas, são algumas das vantagens da utilização destas estruturas. O objetivo principal deste trabalho é analisar numericamente o comportamento da ligação entre viga de seção I com coluna tubular circular, para tanto são consideradas configurações usuais de ligação com anéis externos transversais e chapa de alma. É ainda objetivo trazer um panorama das estruturas tubulares em geral, com o desenvolvimento histórico das pesquisas, e principalmente estabelecer uma compilação dos procedimentos analíticos de cálculo e classificação apresentados pelas normas Eurocode 3 e ANSI/AISC. A análise numérica foi realizada por meio dos pacotes comerciais TRUEGRID® e ANSYS®, os quais aplicam o método dos elementos finitos. Foram empregados modelos que consideram as características mecânicas do aço, como plastificação e encruamento, e ainda as não-linearidades geométricas e de contato. Os resultados numéricos apresentaram coerência razoável com os modelos analíticos normativos. Foi possível o conhecimento do comportamento M-\'fi\' (momento-rotação) das ligações, bem como a determinação dos parâmetros que caracterizam tal relação, como resistência, rigidez inicial e ductilidade. Os estudos comprovaram a eficácia dos anéis externos na distribuição dos esforços oriundos do engastamento parcial da viga, fazendo com que a coluna não seja comprometida. / The application of tubular structures is usually restricted to constructions on which the architectural conception demands them. However, there are also several structural advantages which justify their usage, such as a) reduced exposed area concerning fire and agressive environments; b) high axial compression resistance; c) high local buckling resistance. The aim of this work is the numerical analysis on the behavior of the I beam-circular hollow column connection, usually constituted by an external ring with single plate. It is presented a general view about the researchers development over the years on tubular structures focusing the compilation of the analytical design procedures and Eurocode 3 and ANSI/AISC classification as well. Finite element method softwares TRUEGRID and ANSYS are used for the numerical analysis in order to consider steel mechanical properties such as yielding, hardening and also geometric and contact nonlinearities. Numerical results present good agreement to codes\' analytical models. Analysis lead to understanding the connection\'s moment-rotation behavior and some of its parameters such as resistance, initial stiffness and ductility. It is shown external rings significantlly improve the semi-rigid connections stress distribution at the columns face.

Kyoto University (京都大学) / 0048 / 新制・課程博士 / 博士(工学) / 甲第15367号 / 工博第3246号 / 新制||工||1488(附属図書館) / 27845 / 京都大学大学院工学研究科建築学専攻 / (主査)教授 中島 正愛, 教授 林 康裕, 教授 吹田 啓一郎 / 学位規則第4条第1項該当

This paper is concerned with the behaviour of beam ¿ column connections of steel ¿ concrete composite beams with precast hollow core slabs. Experiments were carried out to investigate the joint rotation characteristics and ultimate moment capacity of these connections. Details of the test specimens, instrumentation, test set-up and test procedures are described. Results obtained for the connection moment capacity, rotation capacity and failure modes are presented. It is found that through proper design and detailing, these simple steel connections display the characteristics of a semi-rigid connection with very little extra cost.

Yes / Elliptical Hollow Sections (EHSs) have been utilized in construction recently because of their visual appearance as well as the potential structural efficiency owing to the presence of the two principle axes. However, little information currently exists for the design of beam to elliptical column connections, which is an essential part of a building structure. Thus, to ensure the safe and economic application of EHSs, a new research project has been initiated. Rotation behaviour of simply bolted beam to concrete-filled elliptical steel column connections was investigated experimentally. Various joint types were considered and the benefits of adopting core concrete and stiffeners were highlighted. This paper covers the experimental studies and simulation of the connections using the ABAQUS standard solver. Comparisons of failure modes and moment vs. rotation relationships of the connections between numerical and experimental results were given. Good agreement has been obtained and the developed finite element model was therefore adopted to conduct a preliminary parametric study to explore the effect of critical parameters on the structural behaviour of beam to concrete-filled elliptical column connections.

Yes / This paper investigated the rotation behaviour of simply bolted I-beam to concrete-filled elliptical steel tubular (CFEST) column connections experimentally. Ten different joint assemblies were tested to failure, with a constant axial compressive load applied to the column and upwards concentrated loads at the beam ends. All of the steel tubes were hot-finished and had a cross-sectional aspect ratio of 2. The orientation of the column and the arrangement of the stiffening plates were taken into consideration. Moment versus rotation relationships and failure modes were compared for each joint, highlighting the benefits of using core concrete and stiffeners in these connections.

No description available.