The MP-AES 4200 using microwave plasma and an atomic emission spectroscopy detector provide a new and improved instrument to the analytical field. In this project will the performance of the equipment be evaluated in controlled NaCl-heavy matrices for selected metals (Cu, Zn, Li) and the result from this will be used to optimize a method for specific samples. These samples consist of combustion ashes from the incineration of hazardous waste and are provided by the company SAKAB AB. The sample preparation consisted of several cycles of L/S 10 followed by microwave assisted dissolution with concentrated HNO3, aqua regia or 18.2 MΩ. An extended amount of metals were quantified for these samples (Al, As, Ba, Ca, Cd, Cr, Cu, Fe, K, Li, Mn, Na, Ni, Pb, V, Zn) and most (not Ca, Li, K or Na) were compared with an ICP-MS instrument equipped with a collision cell used for the elements As, Fe and V. A final experiment was made on an L/S 10 of the samples to attempt to separate the metals from the salt with ion exchange, something that would make it possible to recycle this otherwise unused waste. The detection limits were all in the low μg L-1 except for Cd, Mn and Zn, which were between 2-4 μg L-1. The MP-AES was found to be able to handle matrices up to 5 g L-1 NaCl without a significant loss of response and provided near identical results to the ICP-MS for the elements that could be compared, this did not included the elements not quantified with the ICP-MS or V which was the only element under the limit of detection for the MP-AES. The experiment where an attempt was made to separate the metals from the salt was proven successful after treatment of bark compost and another type of waste ash as cation exchangers.

The ever-increasing quantity of by-products generated from burning coal in the production of electricity has brought about the need for new areas of utilization. This study examined the use of FGD gypsum and fluidized bed combustion ash along with Class F fly ash in the production of low-energy, 100% by-product cement blends. The cement blends used the advantageous properties of the by-product materials to create cementing properties rather than energy intensive clinker used in ordinary portland cement. The FGD gypsum was converted to hemihydrate which rapidly hydrated to provide the cement with early strength gains, whilst the fluidized bed combustion ash reacted with the Class F fly ash to form pozzolanic cementitious phases which provided the longer-term compressive strength and possibly resistance to weathering. The rate of compressive strength gains and minimizing detrimental expansion were two properties of particular interest in the study. Chemical admixtures were used to improve the compressive strengths of the cement mortars and decrease their solubility.

In recent decades, advances in low NOₓ coal combustion and increasingly strict CO₂ reduction mandates have changed power plant boiler operations quite significantly. As a result of these necessary efforts, the characteristics of fly ash generated at many power plants have also changed. In particular, increases in unburned carbon content have been observed with detrimental implications on the utility of these fly ashes in concrete applications. Over the same time period, the combustion of biomass for energy generation has received increased attention due to the potential benefits of reducing CO₂ emissions and improved sustainability when compared to fossil fuel combustion. Biomass is directly burned, gasified, or co-fired with coal to achieve this goal. Currently, close to 120 million metric tons of coal combustion by products are produced in the U.S. annually. As with coal combustion, production of energy from biomass combustion/gasification results in significant by-product generation that must either be productively reused or geologically disposed. While much research effort has been devoted to understanding the properties and potential productive reuse alternatives for coal combustion residuals, relatively little work has been done on the by-products of biomass combustion. This study investigated the properties and engineering behavior of sixteen ash samples that were produced in eleven different power plants. Specifically, three high carbon content Class F fly ashes, eight coal and biomass co-fired ashes, three pure biomass ash samples, and two high quality, low carbon content ash samples, one of which is commercially marketed (for reference) were chosen. The various ash samples were characterized by means of: electron microscopy; laser diffraction and dry sieve particle size analysis; loss on ignition and total organic carbon analysis; specific surface area analysis; as well as x-ray fluorescence and x-ray diffraction. The ash samples were also investigated for their potential engineering application in the fired clay brick industry, as low-cost adsorptive agents, and in alkali activated geopolymer synthesis for geotechnical and geoenvironmental applications. Results from physical and chemical characterization of the ash samples show no significant differences between pure coal ash and coal co-fired with biomass ash samples from the same power plant. However, there are significant morphological, chemical, and mineralogical differences between coal ash and pure biomass ash. Unlike pure coal ash, biomass ash is not composed primarily of aluminosilicate glass cenospheres but rather consists mainly of charred, fibrous woody remnants with elevated calcite content as compared to coal ash. Bench scale fired bricks produced by partial replacement of clay material with high carbon coal ash, co-fired ash, and pure biomass ash, respectively, was successful. Physical properties of a number of the mix designs exceeded the highest ASTM weathering grade requirements. As sorptive agents, high carbon concentrates from coal and co-fired ash samples, along with all the biomass ash samples, showed significant uptake of lead. The unaltered as- received ash samples (i.e. no acid or steam activation) showed only moderate arsenic (V) and selenium (VI) sorption capacity. Finally, solidification/stabilization by geopolymerization of high carbon content, co-fired ash with as little as 3 molar NaOH in the activator solution was successful, possibly paving the way for various geotechnical and geoenvironmental applications in ground improvement and soil/ash-pond stabilization.

The aim of this master thesis is study of possibilities of processing energy by-products, especially coal fly ash and fluidized bed ash, by hydrothermal treatment. Thanks to hydrothermal conditions and proper alkali activation of ashes we can obtain zeolites. Zeolites are microporous crystalline aluminosilicates which are use in many industrial sectors as catalysts, adsorbents and very good ion exchangers. The results of hydrothermal synthesis are influenced by many variable factors. This thesis mainly focused on influence of chosen alkali activator and the concentration of the activator together with a temperature of hydrothermal process. Other factor that is studied is choice of starting materials and solution/ash ratio. Phase composition of prepared samples was characterized by XRD and scanning electron microscopy (SEM). Also cation exchange capacity of prepared samples was determined.

Autoclaved aerated concrete is long-time ecological building material with usefull properties. There needs to be done research of its mineralogical compound for reengineering the production. The main mineral compound of AAC is tobermorite, it increases its mechanical properties. In the presence study, we examine the usage of nature and artificial silicious materials. Also, we investigate the influence of sulfate and alumina admixtures, as well as fluidized bed combustion ash, which can be used as the lime and gypsum replacement. Closure of the study is design of the optimal raw material composition, also hydrothermal treatment of autoclaved aerated concrete. In relation to its mechanical properties, mineralogical composition and cost.