1 |
Numerical modeling of groundwater and air flow between compacted bentonite and fractured crystalline rockDessirier, Benoît January 2016 (has links)
The geological repository for final storage of spent nuclear fuel, envisioned by the Swedish Nuclear Fuel and Management Company (SKB), relies on several barriers: copper canisters deposited in holes in the floor of underground tunnels in deep bedrock, embedded in a buffer of compacted bentonite. The initially unsaturated buffer would take up water from the surrounding rock mass and swell to seal any potential gap. This initial two-phase (gas and liquid) regime with two components (air and water) may impact the final density, swelling pressure and biogeochemical conditions in the buffer. A main objective of this work is to identify factors and mechanisms that govern deposition hole inflow and bentonite wetting under the prevailing two-phase flow conditions in sparsely fractured bedrock. For this purpose, we use the numerical code TOUGH2 to perform two-phase flow simulations, conditioned by a companion field experiment (the Bentonite Rock Interaction Experiment or BRIE) performed in a 417 m deep tunnel of the Äspö Hard Rock Laboratory in southeastern Sweden. The models predict a significant de-saturation of the rock wall, which was confirmed by field data. To predict the early buffer wetting rates and patterns, the position of local flowing fractures and estimates of local rock matrix permeability appear more important than the total open hole groundwater inflow. A global sensitivity analysis showed that the buffer wetting time and the persistence of unsaturated conditions over extended periods of time in the rock depend primarily on the local fracture positions, rock matrix permeability, ventilation conditions in the tunnel and pressure far in the rock. Dismantling photographs from BRIE were used to reconstruct a fine-scale snapshot of saturation at the bentonite/rock interface, showing tremendous spatial variability. The high level of heterogeneity in the rock generates complex two-phase flow phenomena (air trapping, dissolution), which need to be accounted for in buffer design and rock suitability criteria. In particular, results suggest that uncertainties regarding two-phase flow behavior are relatively high close to residual air saturation, which may also have important implications for other applications involving two-phase flows, such as geological storage of carbon dioxide. / <p>At the time of the doctoral defense, the following papers were unpublished and had a status as follows: Paper 1: Manuscript. Paper 4: Manuscript.</p>
|
2 |
CHM (Chemo-Hydro-Mechanical) Behavior of Barmer-1 Bentonite in the Context of Deep Geological Repositories for Safe Disposal of Nuclear WasteRavi, K January 2013 (has links) (PDF)
Deep geological repository (DGR) for disposal of high-level radioactive waste
(HLW) is designed to rely on successive superimposed barrier systems to isolate the
waste from the biosphere. This multiple barrier system comprises the natural geological barrier provided by the repository host rock and its surrounding and an engineered barrier system (EBS). The EBS represents the synthetic, engineered materials placed within the natural barrier, comprising array of components such as waste form, waste canisters, buffer materials, backfill and seals. The buffer will enclose the waste canisters from all directions and act as a barrier between canisters and host rock of the repository. It is designed to stabilise the evolving thermo-hydro-mechanical-chemical stresses in the repository over a long period (nearly 1000 years) to retard radionuclides from reaching
biosphere. Bentonite clay or bentonite-sand mix have been chosen as buffer materials in
EBS design in various countries pursuing deep geological repository method.
The bentonite buffer is the most important barrier among the other EBS components for a geological repository. The safety of repository depends to a large extent
on proper functioning of buffer over a very long period of time during which it must
remain physically, chemically and mineralogically stable. The long term stability of bentonite buffer depends on varying temperature and evolution of groundwater composition of host rocks in a complex way. The groundwater in the vicinity of deep crystalline rock is often characterized by high solute concentrations and the geotechnical engineering response of bentonite buffer could be affected by the dissolved salt concentration of the inflowing ground water. Also during the initial period, radiogenic heat produced in waste canisters would radiate into buffer and the heat generated would lead to drying and some shrinkage of bentonite buffer close to canister. This could alter the dry density, moisture content and in turn the hydro-mechanical properties of bentonite
buffer in DGR conditions.
India has variety of bentonite deposits in North-Western states of Rajasthan and
Gujarat. Previous studies on Indian bentonites suggest that bentonite from Barmer district of Rajasthan (termed as Barmer-1 bentonite) is suitable to serve as buffer material in DGR conditions. Nuclear power agencies of several countries have identified suitable bentonites for use as buffer in DGR through laboratory experiments and large scale underground testing facilities. Physico-chemical, mineralogical and engineering properties of Kunigel VI, Kyungju, GMZ, FoCa clay, MX-80, FEBEX and Avonseal bentonites have been extensively studied by Japan, South Korea, China, Belgium, Sweden, Spain, Canada. It is hence essential to examine the suitability of Barmer-1 bentonite as potential buffer in DGR and compare its physico-chemical and hydromechanical properties with bentonite buffers identified by other countries. The significant factors that impact the long-term stability of bentonite buffer in DGR include variations in moisture content, dry density and pore water chemistry. With a view to address these issues, the hydromechanical response of 70 % Barmer-1 bentonite + 30 % river sand mix
(termed bentonite enhanced sand, BES specimens) under varying moisture content, dry density and pore water salt concentration conditions have been examined. The broad scope of the work includes:
1) Characterise the physico-chemical and hydro-mechanical properties of Barmer-1
bentonite from Rajasthan, India and compare its properties with bentonite buffers
reported in literature.
2) Examine the influence of variations in dissolved salt concentration (of infiltrating solution), dry density and moisture content of compacted BES specimens on their hydro-mechanical response; the hydro-mechanical properties include, swell pressure, soil water characteristic curve (SWCC), unsaturated hydraulic conductivity, moisture diffusivity and unconfined compression strength.
Organization of thesis:
After the first introductory chapter, a detailed review of literature is performed to highlight the need for detailed characterisation of physico-chemical and hydromechanical properties of Barmer-1 bentonite for its possible application in DGR in the Indian context. Further, existing literature on hydro-mechanical response of bentonite buffer to changes in physical (degree of saturation/moisture content, dry density) and physico-chemical (solute concentration in pore water) is reviewed to define the scope and objectives of the present thesis in Chapter 2.
Chapter 3 presents a detailed experimental programme of the study.
Chapter 4 characterises Barmer-1 bentonite for physico-chemical (cation exchange
capacity, pore water salinity, exchangeable sodium percentage) and hydro-mechanical
properties, such as, swell pressure, saturated permeability, soil water characteristic curve (SWCC) and unconfined compression strength. The properties of Barmer-1 bentonite are compared with bentonite buffers reported in literature and generalized equations for determining swell pressure and saturated permeability coefficient of bentonite buffers are
arrived at.
Chapter 5 describes a method to determine solute concentrations in the inter-lamellar
and free-solutions of compacted BES (bentonite enhanced sand) specimens. The solute concentrations in micro and macro pore solutions are used to examine the role of osmotic flow on swell pressures developed by compacted BES specimens (dry density 1.50-2.00 Mg/m3) inundated with distilled water and NaCl solutions (1000-5000 mg/L). The number of hydration layers developed by the compacted BES specimens on inundation
with salt solutions in constant volume swell pressure tests is controlled by cation
hydration/osmotic flow. The cation hydration of specimens compacted to dry density of
2.00 Mg/m3 is mainly driven by matric suction prevailing in the clay microtructure as the number of hydration layers developed at wetting equilibrium are independent of the total dissolved solids (TDS) of the wetting solution. Consequently, the swell pressures of specimens compacted to 2.00 Mg/m3 were insensitive to the salt concentration of the inundating solution. The cation hydration of specimens compacted to dry density of 1.50 Mg/m3 is driven by both matric suction (prevailing in the clay micro-structure) and osmotic flow as the number of hydration layers developed at wetting equilibrium is sensitive to the TDS of the wetting solution. Expectedly, the swell pressures of specimens
compacted to 1.50 Mg/m3 responded to changes in salt concentration of the inundating solution. The 1.75 Mg/m3
specimens show behaviour that is intermediate to the 1.50 and 2.00 Mg/m3
series specimens.
Chapter 6 examines the influence of initial degree of saturation on swell pressures
developed by the compacted BES specimens (dry density range: 1.40- 2.00 Mg/m3) on
wetting with distilled water from micro-structural considerations. The micro-structure of the bentonite specimens are examined in the compacted and wetted states by performing X-ray diffraction measurements. The initial degree of saturation is varied by adding requisite amount of distilled water to the oven-dried BES mix and compacting the moist
mixes to the desired density. The montmorillonite fraction in the BES specimens is responsible for moisture absorption during compaction and development of swell pressure in the constant volume oedometer tests. Consequently, it was considered reasonable to calculate degree of saturation based on EMDD (effective montmorillonite dry density) values and correlate the developed swell pressure values with degree of saturation of montmorillonite voids (Sr,MF). XRD measurements with compacted and
wetted specimens demonstrated that if specimens of density series developed similar number of hydration layers on wetting under constant volume condition they exhibited similar swell pressures, as was the case for specimens belonging to 1.40 and 1.50 Mg/m3 series. With specimens belonging to 1.75 and 2.00 Mg/m3 series, greater number of hydration layers were developed by specimens that were less saturated initially (smaller initial Sr,MF) and consequently such specimens developed larger swell pressures. When specimens developed similar number of hydration layers in the wetted state, the compaction dry density determined the swell pressure.
Chapter 7 examines the influence of salt concentration of infiltrating solution (sodium chloride concentration ranges from 1000- 5000 mg/L) on SWCC relations, unsaturated permeability and moisture diffusivity of compacted BES specimens. Analysis of the experimental and Brooks and Corey best fit plots revealed that infiltration of sodium chloride solutions had progressively lesser influence on the micro-structure and consequently on the SWCC relations with increase in dry density of the compacted specimens. The micro-structure and SWCC relations of specimens compacted to 1.50 Mg/m3 were most affected, specimens compacted to 1.75 Mg/m3 were less affected,
while specimens compacted to 2.00 Mg/m3
were unaffected by infiltration of sodium
chloride solutions. Variations in dry density of compacted bentonite impacts the pore space available for moisture flow, while, salinity of wetting fluid impacts the pore structure from associated physico-chemical changes in clay structure. Experimental results showed that the unsaturated permeability coefficient is insensitive to variations in dry density and solute concentration of wetting liquid, while, the effective hydraulic diffusivity is impacted by variations in these parameters.
Chapter 8 summarises the major findings of the study.
|
3 |
CHM (Chemo-Hydro-Mechanical) Behavior of Barmer-1 Bentonite in the Context of Deep Geological Repositories for Safe Disposal of Nuclear WasteRavi, K January 2013 (has links) (PDF)
Deep geological repository (DGR) for disposal of high-level radioactive waste
(HLW) is designed to rely on successive superimposed barrier systems to isolate the
waste from the biosphere. This multiple barrier system comprises the natural geological barrier provided by the repository host rock and its surrounding and an engineered barrier system (EBS). The EBS represents the synthetic, engineered materials placed within the natural barrier, comprising array of components such as waste form, waste canisters, buffer materials, backfill and seals. The buffer will enclose the waste canisters from all directions and act as a barrier between canisters and host rock of the repository. It is designed to stabilise the evolving thermo-hydro-mechanical-chemical stresses in the repository over a long period (nearly 1000 years) to retard radionuclides from reaching
biosphere. Bentonite clay or bentonite-sand mix have been chosen as buffer materials in
EBS design in various countries pursuing deep geological repository method.
The bentonite buffer is the most important barrier among the other EBS components for a geological repository. The safety of repository depends to a large extent
on proper functioning of buffer over a very long period of time during which it must
remain physically, chemically and mineralogically stable. The long term stability of bentonite buffer depends on varying temperature and evolution of groundwater composition of host rocks in a complex way. The groundwater in the vicinity of deep crystalline rock is often characterized by high solute concentrations and the geotechnical engineering response of bentonite buffer could be affected by the dissolved salt concentration of the inflowing ground water. Also during the initial period, radiogenic heat produced in waste canisters would radiate into buffer and the heat generated would lead to drying and some shrinkage of bentonite buffer close to canister. This could alter the dry density, moisture content and in turn the hydro-mechanical properties of bentonite
buffer in DGR conditions.
India has variety of bentonite deposits in North-Western states of Rajasthan and
Gujarat. Previous studies on Indian bentonites suggest that bentonite from Barmer district of Rajasthan (termed as Barmer-1 bentonite) is suitable to serve as buffer material in DGR conditions. Nuclear power agencies of several countries have identified suitable bentonites for use as buffer in DGR through laboratory experiments and large scale underground testing facilities. Physico-chemical, mineralogical and engineering properties of Kunigel VI, Kyungju, GMZ, FoCa clay, MX-80, FEBEX and Avonseal bentonites have been extensively studied by Japan, South Korea, China, Belgium, Sweden, Spain, Canada. It is hence essential to examine the suitability of Barmer-1 bentonite as potential buffer in DGR and compare its physico-chemical and hydromechanical properties with bentonite buffers identified by other countries. The significant factors that impact the long-term stability of bentonite buffer in DGR include variations in moisture content, dry density and pore water chemistry. With a view to address these issues, the hydromechanical response of 70 % Barmer-1 bentonite + 30 % river sand mix
(termed bentonite enhanced sand, BES specimens) under varying moisture content, dry density and pore water salt concentration conditions have been examined. The broad scope of the work includes:
1) Characterise the physico-chemical and hydro-mechanical properties of Barmer-1
bentonite from Rajasthan, India and compare its properties with bentonite buffers
reported in literature.
2) Examine the influence of variations in dissolved salt concentration (of infiltrating solution), dry density and moisture content of compacted BES specimens on their hydro-mechanical response; the hydro-mechanical properties include, swell pressure, soil water characteristic curve (SWCC), unsaturated hydraulic conductivity, moisture diffusivity and unconfined compression strength.
Organization of thesis:
After the first introductory chapter, a detailed review of literature is performed to highlight the need for detailed characterisation of physico-chemical and hydromechanical properties of Barmer-1 bentonite for its possible application in DGR in the Indian context. Further, existing literature on hydro-mechanical response of bentonite buffer to changes in physical (degree of saturation/moisture content, dry density) and physico-chemical (solute concentration in pore water) is reviewed to define the scope and objectives of the present thesis in Chapter 2.
Chapter 3 presents a detailed experimental programme of the study.
Chapter 4 characterises Barmer-1 bentonite for physico-chemical (cation exchange
capacity, pore water salinity, exchangeable sodium percentage) and hydro-mechanical
properties, such as, swell pressure, saturated permeability, soil water characteristic curve (SWCC) and unconfined compression strength. The properties of Barmer-1 bentonite are compared with bentonite buffers reported in literature and generalized equations for determining swell pressure and saturated permeability coefficient of bentonite buffers are
arrived at.
Chapter 5 describes a method to determine solute concentrations in the inter-lamellar
and free-solutions of compacted BES (bentonite enhanced sand) specimens. The solute concentrations in micro and macro pore solutions are used to examine the role of osmotic flow on swell pressures developed by compacted BES specimens (dry density 1.50-2.00 Mg/m3) inundated with distilled water and NaCl solutions (1000-5000 mg/L). The number of hydration layers developed by the compacted BES specimens on inundation
with salt solutions in constant volume swell pressure tests is controlled by cation
hydration/osmotic flow. The cation hydration of specimens compacted to dry density of
2.00 Mg/m3 is mainly driven by matric suction prevailing in the clay microtructure as the number of hydration layers developed at wetting equilibrium are independent of the total dissolved solids (TDS) of the wetting solution. Consequently, the swell pressures of specimens compacted to 2.00 Mg/m3 were insensitive to the salt concentration of the inundating solution. The cation hydration of specimens compacted to dry density of 1.50 Mg/m3 is driven by both matric suction (prevailing in the clay micro-structure) and osmotic flow as the number of hydration layers developed at wetting equilibrium is sensitive to the TDS of the wetting solution. Expectedly, the swell pressures of specimens
compacted to 1.50 Mg/m3 responded to changes in salt concentration of the inundating solution. The 1.75 Mg/m3
specimens show behaviour that is intermediate to the 1.50 and 2.00 Mg/m3
series specimens.
Chapter 6 examines the influence of initial degree of saturation on swell pressures
developed by the compacted BES specimens (dry density range: 1.40- 2.00 Mg/m3) on
wetting with distilled water from micro-structural considerations. The micro-structure of the bentonite specimens are examined in the compacted and wetted states by performing X-ray diffraction measurements. The initial degree of saturation is varied by adding requisite amount of distilled water to the oven-dried BES mix and compacting the moist
mixes to the desired density. The montmorillonite fraction in the BES specimens is responsible for moisture absorption during compaction and development of swell pressure in the constant volume oedometer tests. Consequently, it was considered reasonable to calculate degree of saturation based on EMDD (effective montmorillonite dry density) values and correlate the developed swell pressure values with degree of saturation of montmorillonite voids (Sr,MF). XRD measurements with compacted and
wetted specimens demonstrated that if specimens of density series developed similar number of hydration layers on wetting under constant volume condition they exhibited similar swell pressures, as was the case for specimens belonging to 1.40 and 1.50 Mg/m3 series. With specimens belonging to 1.75 and 2.00 Mg/m3 series, greater number of hydration layers were developed by specimens that were less saturated initially (smaller initial Sr,MF) and consequently such specimens developed larger swell pressures. When specimens developed similar number of hydration layers in the wetted state, the compaction dry density determined the swell pressure.
Chapter 7 examines the influence of salt concentration of infiltrating solution (sodium chloride concentration ranges from 1000- 5000 mg/L) on SWCC relations, unsaturated permeability and moisture diffusivity of compacted BES specimens. Analysis of the experimental and Brooks and Corey best fit plots revealed that infiltration of sodium chloride solutions had progressively lesser influence on the micro-structure and consequently on the SWCC relations with increase in dry density of the compacted specimens. The micro-structure and SWCC relations of specimens compacted to 1.50 Mg/m3 were most affected, specimens compacted to 1.75 Mg/m3 were less affected,
while specimens compacted to 2.00 Mg/m3
were unaffected by infiltration of sodium
chloride solutions. Variations in dry density of compacted bentonite impacts the pore space available for moisture flow, while, salinity of wetting fluid impacts the pore structure from associated physico-chemical changes in clay structure. Experimental results showed that the unsaturated permeability coefficient is insensitive to variations in dry density and solute concentration of wetting liquid, while, the effective hydraulic diffusivity is impacted by variations in these parameters.
Chapter 8 summarises the major findings of the study.
|
Page generated in 0.1188 seconds