This research study is aimed at assisting the Texas Department of Transportation (TxDOT) in making a transition from the use of the AASHTO Standard Specifications for Highway Bridges to the AASHTO LRFD Bridge Design Specifications for the design of prestressed concrete bridges. It was identified that Type C and AASHTO Type IV are among the most common girder types used by TxDOT for prestressed concrete bridges. This study is specific to these two types of bridges. Guidelines are provided to tailor TxDOT's design practices to meet the requirements of the LRFD Specifications. Detailed design examples for an AASHTO Type IV girder using both the AASHTO Standard Specifications and AASHTO LRFD Specifications are developed and compared. These examples will serve as a reference for TxDOT bridge design engineers. A parametric study for AASHTO Type IV and Type C girders is conducted using span length, girder spacing, and strand diameter as the major parameters that are varied. Based on the results obtained from the parametric study, two critical areas are identified where significant changes in design results are observed when comparing Standard and LRFD designs. The critical areas are the transverse shear requirements and interface shear requirements, and these are further investigated. The interface shear reinforcement requirements are observed to increase significantly when the LRFD Specifications are used for design. New provisions for interface shear design that have been proposed to be included in the LRFD Specifications in 2007 were evaluated. It was observed that the proposed interface shear provisions will significantly reduce the difference between the interface shear reinforcement requirements for corresponding Standard and LRFD designs.The transverse shear reinforcement requirements are found to be varying marginally in some cases and significantly in most of the cases when comparing LRFD designs to Standard designs. The variation in the transverse shear reinforcement requirement is attributed to differences in the shear models used in the two specifications. The LRFD Specifications use a variable truss analogy based on the Modified Compression Field Theory (MCFT). The Standard Specifications use a constant 45-degree truss analogy method for its shear design provisions. The two methodologies are compared and major differences are noted.

As part of the ongoing research on shear at the Phil M. Ferguson Structural Engineering Laboratory (FSEL) located at The University of Texas at Austin, the anchorage controlled shear capacity of prestressed concrete bridge girders was in this research studied in two distinct ways, experimentally and analytically. The results of this research are an important step towards improving understanding of strand anchorage related issues. For the experimental program, two full-scale Tx46 prestressed concrete bridge girders were fabricated at FSEL. The Tx46 girders were topped with a concrete, composite deck. Both ends of the two girders were instrumented and tested. For the analytical program, a new Anchorage Evaluation Database (AEDB) was developed, by filtering and expanding the University of Texas Prestressed Concrete Shear Database (UTPCSDB), and then evaluated. The AEDB contained 72 shear tests, of which 25 were anchorage failures and 47 were shear failures. The results and analysis from the experimental and analytical programs generated the following three main conclusions: (1) A reasonable percentage of debonding in Tx Girders does not have a marked impact on girder shear capacity calculated using the 2010 AASHTO LRFD General Procedure. (2) The AASHTO anchorage equation is conservative but not accurate. In other words, this equation cannot be used to accurately differentiate between a shear failure and an anchorage failure. In regards to conservativeness, anchorage failures in AASHTO-type girders may lead to unconservative results with respect to the 2010 AASHTO LRFD General Procedure. (3) The 2010 AASHTO anchorage resistance model and its corresponding equation do not apply to Tx Girders. Because of the Tx Girders' wider bottom flange, cracks do not propagate across the strands as they do in AASHTO-type girders. This fact yields overly conservative results for Tx Girders with respect to AASHTO Equation 5.8.3.5-1. In summary, this research uncovered the short-sided nature of the AASHTO anchorage design method. Given its short-comings, there is an obvious need for a validated, comprehensive, and rational approach to anchorage design that considers strength and serviceability. To appropriately develop this method, additional full-scale experimental testing is needed to expand the AEDB, as currently there are not enough tests to distinguish major, general trends and variables. Any future additional research would be expected to further validate and expand the significant findings that this research has produced and so take the next step toward safer, more-efficient bridge designs. / text

No description available.

This thesis presents the results of a research project that tested five friction reducing techniques on the bearing ends of precast prestressed concrete bridge girders. The five techniques were the following: an oil coated surface, embedded steel plate with an oil coated surface, embedded steel angle with an oil coated surface, teflon pad, and a wax lubricant.

An effective, viable design solution for the elevated viaduct guideway for Universal Freight Shuttle (UFS) system championed by Texas Transportation Institute (TTI) is presented. The proposed precast elevated UFS bridge system is analyzed for the operational vehicular loading as provided by TTI and a number of design alternatives for the various bridge components are provided. This includes: the design of the fully precast deck panels for long continuous spans, design of the shear connectors resisting interface shear at bridge deck-girder interface, design of structurally efficient and cost-effective trough girders and its design alternative with I-girders, and economic and long-term serviceable design of bridge piers. A literature review and study of the existing precast bridges is presented for the state-of-the-art and practice, design specifications and publications by AASHTO, State Department of Transportation and other agencies. These existing systems are refined to determine the most appropriate specification for the proposed bridge components by integrating the planning, design, fabrication and construction techniques to ensure high precision freight shuttle movement, construction feasibility, safety, life-cycle cost, durability and serviceability requirements. The design concept presented is a deviation from the conventional railways and highways design. The best practices and specifications of AASHTO and AREMA are combined suitably in this research to suit the major requirements of the project. A combination of the design philosophy with appropriate construction techniques has been blended to devise a system which is efficient for offsite manufacture of components for construction of the bridge and adaptable to the different bridge configurations. Based on the design results, it is found that precast concrete deck panels in combination with precast, prestressed concrete trough girders provides the most efficient superstructure solution for this project. The Damage Avoidance Design for the precast bridge piers along with the precast superstructure provides a system with comparable structural performance along with other benefits such as long term serviceability, economical sections, practically transportable units, modular simplicity for relocation as desired and ability to offer space for commercial usage. The steps for construction of the bridge is schematically presented and sequentially explained.

Maintenance and repair of deteriorating civil infrastructure are global problems requiring significant attention and resources. Accurate measurements of civil infrastructure enable lower repair and rehabilitation costs if mitigation techniques are deployed at earlier stages of deterioration. This research describes an infrastructure inspection solution to scan concrete bridge decks for internal cracking at high speeds. Internal cracking within bridge decks, known as delamination, is a particularly difficult defect to identify because it is often not detectable through visual inspection. State-of-the practice testing approaches involve the use of slow and subjective manual sounding techniques and costly lane closures. The need for an improved testing approach has led to decades of research investigating the use of acoustic impact-echo testing to detect bridge deck delaminations. The research presented here consists of a study of the acoustic radiation patterns of delamination defects when they are impacted. Acoustic data were collected on an in-service bridge deck and compared to acoustic data collected on defects in decommissioned bridge deck slabs and on simulated delaminations. This study examined cases of ideal and non-ideal delaminations on the in-service bridge deck and identified characteristics of non-ideal delaminations. An apparatus consisting of a high-speed impact-echo platform and recording suite was designed and constructed. Using this towed apparatus, an order-of-magnitude increase in scanning speed was obtained over other reported methods. Significant design effort was employed to achieve synchronization between different sensing devices using networked computer systems. Analysis was also developed to process and automatically classify acoustic responses to determine the presence and location of delaminations. Demonstrated performance against ground truth data obtained on an in-service bridge deck includes an achievement of approximately 90% probability of detection with only a 2% false alarm rate within 0.30 m. Because of the need to classify acoustic data when ground truth may not be obtainable, a new outlier rejection algorithm, which robustly removes outliers for classification on both simulated and field test data, was also developed. These contributions advance state-of-the-art bridge inspection and also lay the groundwork for additional studies of bridge deck deterioration processes. The framework also demonstrates how a tedious, subjective, and manual inspection process can be automated using advanced excitation tools, signal processing, and machine learning.

In early 2020, cracks were discovered on the bridge crossing the Torne River at Autio. This resulted in an investigation being launched to determine the structural state of the bridge. In conjunction with this investigation, monitoring equipment was installed on the bridge, which enabled the collection of measured strain at four critical points on the bridge.  In this thesis the measured strain was used to approximate stresses in the prestressing cables and thereby calculate the effects of fatigue on the bridge. Two different structural standards were used to calculate the results: Eurocode 2, and fib Model Code 2010. Likewise, two different cycle-counting methods were used to calculate the results: the Rainflow-algorithm, and the largest-magnitude approach.  Regardless of structural standard or cycle-counting method, the results indicate that the effects of fatigue are neither an issue for the bridge, currently, nor will it be in the expected lifetime of the bridge.

No description available.

Corrosion of reinforcing steel is a major cause of damage to bridges in the United States. A possible solution to the corrosion issue is carbon fiber reinforced polymer (CFRP) material. CFRP material has been implemented as flexural reinforcement in many cases, but not as transverse reinforcing. The CFRP material studied in this thesis was NEFMAC grid, which consists of vertical and horizontal CFRP tows that form an 8 in. by 10 in. grid. The use of NEFMAC grid as transverse reinforcing has not been previously investigated. First, the development length of NEFMAC grid was determined. Next, an 18 ft long 19 in. deep beam, modeled after prestressed Bulb-T beams, was created with NEFMAC grid reinforcement. The beam was loaded with a single point load near the support to induce shear failure. Beams were fitted with instrumentation to capture shear cracking data. Shear capacity calculations following four methods were compared to test results. Lastly, a parametric study with strut-and-tie modeling was performed on Precast Bulb-T (PCBT) girders to determine the amount of CFRP grid needed for reinforcement in the anchorage zone. This thesis concludes that NEFMAC grid is a viable shear design option and presents the initial recommendations for design methods. These methods provide a basis for the design of NEFMAC grid shear reinforcing that could be used as a starting point for future testing of full scale specimens. When designing with NEFMAC grid, the full manufacturer's guaranteed strength should be used as it is the average reduced by three standard deviations. AASHTO modified compression field theory provides the best prediction of shear capacity. For anchorage zone design, working stress limits for CFRP grids need to be increased to allow more of the strength to be implemented in design. / Master of Science

Corrosion of reinforcing steel causes shorter life spans in bridges throughout the United States. The use of carbon fiber reinforced polymer (CFRP) materials as the flexural reinforcement in bridge girders has been extensively studied. However, CFRP transverse reinforcement has not been as rigorously investigated, and many studies have focused on CFCC stirrups. The use of C-Grid as an option for transverse reinforcing has not been previously investigated. This thesis concludes that C-Grid is a viable shear design option and presents the initial recommendations for design methods. These methods provide a basis for the design of C-Grid shear reinforcing that could be used as a starting point for future testing of full scale specimens. This testing program first determined the mechanical properties of C-Grid and its development length. Four 18 ft long 19 in. deep beams, modeled after prestressed Bulb-T beams, were created to test the C-Grid, as well as steel and CFCC stirrups. The beams were loaded with a single point load closer to one end to create a larger shear load for a given flexural moment. Overall beam displacement was measured to determine when flexural reinforcement yielding was reached, and beams were fitted with rosettes and instrumentation to capture initiation of shear cracking. Shear capacity calculations following four methods were compared to test results. The design method should follow the AASHTO modified compression field theory with equations for β and θ. The manufacturer's guaranteed strength should be used for design as long as that strength is the average reduced by three standard deviations. Shear crack widths are controlled to a similar size as steel stirrups when using at least two layers of grid. / Master of Science