No description available.

published_or_final_version / Civil Engineering / Doctoral / Doctor of Philosophy

published_or_final_version / abstract / Civil Engineering / Doctoral / Doctor of Philosophy

A dissertation submitted to the Faculty of Engineering, University of the Wttwatersrand, Johannesburg, in fulfilment of th e degree of Master of science in Engineering Johannesburg 1988 / This dissertation addresses the question of the fracture behaviour of notched concrete and mortar beams. The major purpose of the work was to study the development of the micro-cracked zone and identify the point at which main crack growth began, and thus to characterise concrete and mortar at the start of main crack growth. Notched concrete and mortur beams of width 100 mm, depth either 200 mm or 300 nun, and with a span/depth ratio of three, were tested. Measurements of midspan deflection, midspan load, surface displacements across the fracturing section and ultrasonic pulse transit time were made. Ordinary Portland cement and mineral aggregates were used for the concrete and mortar beams. The J'■integral, surface displacements across the fracturing section and ultrasonic pulse transit time measurements were used to detect the onset of main crack growth. It was found that a reduction in the load carrying capacity of concrete and mortar is possible due to micro-cracking only. The value of the J-integral at the start of main crack growth was found to be essentially the same for concrete and mortar. The value of the J-integral at the start of micro-cracking was ■ < found to be essentially the same for concrete and mortar, and about 40% of the value of the J-integral at the start of main crack growth. The value of the J-integral at the start of micro-cracking and at the start of main crack growth was found, on average, to increase for an increase in beam depth. Surface displacements across the fracturing section showed the tension zone at the start of main crack growth to be approximately twice the size of the compression zone for both concrete and mortar. The'size of the micro-cracked zone, as determined from surface displacements across the fracturing section, was found to be 42% of the residual ligament depth for concrete, and 41% of the residual ligament depth for mortar. Scatter in the results was found to be considerable, thus meaning that only general trends could be identified

No description available.

The construction of coastal ports requires the use of materials that meet the demands of the marine environment, to prevent underwater concrete structures from cracking and spalling easily; basalt fiber is used to delay the expansion of concrete and prevent the formation of cracks. This research studies the behavior of concrete for prefabricated piles with Portland Cement Type I and basalt fibers added in 0.1%, 0.3% and 0.6%; the results indicate that the fiber is suitable for concrete, the slump decreases, the compressive strength increases for specimens cured in tap water and sea water, the relationship between resistances does not vary, and the depth of carbonation decreases.

No description available.

Low temperature cracking is attributed to tensile stresses induced in an asphalt concrete pavement that develop when the pavement is subjected to a cold temperature. Cracking results in poor ride quality and a reduction in service life of the pavement. Low temperature cracking has been predicted by regression equations, mechanistic approaches and by simulation measurements. The purpose of the study reported herein is to (1) evaluate the Thermal Stress Restrained Specimen Test (TSRST) as an accelerated performance test to simulate low temperature cracking of asphalt concrete mixtures and (2) develop a deterministic and probabilistic model to predict low temperature cracking with TSRST results. Construction histories, cracking observations and temperature data were collected for five test roads in Alaska, Pennsylvania and Finland. A full scale and fully controlled low temperature cracking test program was conducted at the U.S. Army Cold Regions Research and Engineering Laboratory (USACRREL). Specimens were fabricated in the laboratory with original asphalt cements and aggregates from the test roads. In addition, asphalt concrete pavement specimens were cut from the test sections. The TSRST results obtained for these samples were correlated with the field observations. Based on a statistical analysis of the data, the TSRST fracture temperature is associated with the field cracking temperature and crack frequency for the test roads where mixture properties dominated low temperature cracking. It was concluded that the TSRST can be used to simulate low temperature cracking of asphalt concrete mixtures. A deterministic and a probabilistic model were developed to predict crack spacing as a function of time using the TSRST results, pavement thickness and bulk density, pavement restraint conditions and air temperature. The affect of aging on pavement properties was incorporated in the models by predicting the field aging with Long Term Oven Aging (LTOA) treatment in the laboratory. The calculation of the crack spacing is based on the theory that the pavement slab cracks when the pavement temperature reaches the cracking temperature of the mixture and the slab is fully restrained. The deterministic model predicts crack spacing with time whereas the probabilistic model predicts crack spacing and its variation with time and yields the reliability of the design with regard to a minimum acceptable crack spacing criterion defined by road authorities. The models were verified by comparing the predicted crack spacings for the five test roads to the observed crack spacings. The probabilistic model is recommended for use in predicting the low temperature cracking of asphalt concrete mixtures. / Graduation date: 1994

Thermal distress in asphalt concrete pavements is a widespread problem around the world. Thermal cracking can be divided into two modes of distress: low temperature cracking and thermal fatigue cracking. Low temperature cracking results from extremely cold temperatures; thermal fatigue cracking results from daily temperature cycles. Low temperature cracking is attributed to tensile stresses induced in the asphalt concrete pavement as the temperature drops to an extremely low temperature. If the pavement is cooled, tensile stresses develop as a result of the pavement's tendency to contract. The friction between the pavement and the base layer resists the contraction. If the tensile stress equals the strength of the mixture at that temperature, a micro-crack develops at the surface of the pavement. Under repeated temperature cycles, the crack penetrates the full depth and across the asphalt concrete layer. The thermal stress restrained specimen test (TSRST) was identified as an accelerated laboratory test to evaluate the thermal cracking resistance of asphalt concrete mixtures. The TSRST system developed at OSU includes a load system, data control/acquisition system and software, temperature control system, and specimen alignment stand. The overall system is controlled by a personal computer. A TSRST is conducted by cooling an asphalt concrete specimen at a specified rate while monitoring the specimen at constant length. A typical thermally-induced stress curve is divided into two parts: relaxation and non-relaxation. The temperature at which the curve is divided into two parts is termed the transition temperature. The temperature at fracture is termed the fracture temperature and the maximum stress is the fracture strength. An extensive number of TSRSTs over a wide range of conditions were performed to investigate the thermal cracking resistance of asphalt concrete mixtures. The TSRST results provided a very strong indication of low temperature cracking resistance for all mixtures considered. A ranking of mixtures for low temperature cracking resistance based on the TSRST fracture temperature was in excellent agreement with a ranking based on the physical properties of the asphalt cements. It is highly recommended that the TSRST be used in mix evaluation to identify low temperature cracking resistance of asphalt concrete mixtures. The TSRST showed very promising results regarding the effect of all variables which are currently considered to affect the low temperature cracking of mixtures. The variables considered to have significant affect on the low temperature cracking resistance of mixtures in this study include asphalt type, aggregate type, degree of aging, cooling rate, and stress relaxation. / Graduation date: 1994

The research in the thesis investigates the use of minimal path techniques to track and detect cracks, modeled as curves, in critical infrastructure like pavements and bridges. We developed a novel minimal path algorithm to detect curves with complex topology that may have both closed cycles and open sections using an arbitrary point on the curve as the sole input. Specically, we applied the novel algorithm to three problems: semi-automatic crack detection, detection of continuous cracks for crack sealing applications and detection of crack growth in structures like bridges. The current state of the art minimal path techniques only work with prior knowledge of either both terminal points or one terminal point plus total length of the curve. For curves with multiple branches, all terminal points need to be known. Therefore, we developed a new algorithm that detects curves and relaxes the necessary user input to one arbitrary point on the curve. The document presents the systematic development of this algorithm in three stages. First, an algorithm that can detect open curves with branches was formulated. Then this algorithm was modied to detect curves that also have closed cycles. Finally, a robust curve detection algorithm was devised that can increase the accuracy of curve detection. The algorithm was applied to crack images and the results of crack detection were validated against the ground truth. In addition, the algorithm was also used to detect features like catheter tube and optical nerves in medical images. The results demonstrate that the algorithm is able to accurately detect objects that can be modeled as open curves.