• Refine Query
  • Source
  • Publication year
  • to
  • Language
  • 1
  • 1
  • Tagged with
  • 2
  • 2
  • 1
  • 1
  • 1
  • 1
  • 1
  • 1
  • 1
  • 1
  • 1
  • 1
  • 1
  • 1
  • 1
  • About
  • The Global ETD Search service is a free service for researchers to find electronic theses and dissertations. This service is provided by the Networked Digital Library of Theses and Dissertations.
    Our metadata is collected from universities around the world. If you manage a university/consortium/country archive and want to be added, details can be found on the NDLTD website.
1

Relationship between Frequency of RFID Tags and Its Ability to Penetrate Fresh Concrete

Sridharan, Rajasekaran 2010 May 1900 (has links)
The concrete maturity method can be utilized to determine in situ strength of concrete. It uses the temperature of concrete to determine a maturity index that can then be used to determine strength of concrete. However, monitoring the concrete temperature using thermocouples brings up a wiring issue, which is not advisable in an equipment and human intensive area like a construction site. One of the ways to get around this wiring issue is to use Radio Frequency Identification (RFID) technology, which is capable of transmitting information wirelessly. Previous research implemented using ultra high frequency RFID tags embedded in fresh concrete found that water could be the impediment for transmitting RFID signal from within concrete during early stages of curing. From literature it was found that lower the frequency, better the chances of the wave penetrating water. The objective of the research was to figure out whether the frequency of RFID tags has any relationship with the readability of RFID tags embedded in fresh concrete. For this investigation, low frequency, high frequency, and ultra high frequency RFID tags were tested within fresh concrete to see any difference between tags in terms of transmitting information. This experiment was carried out in a controlled space to reduce the number of variables affecting the experiment outcome. The low frequency, high frequency, and ultra high frequency RFID tags were placed within 2 in x 3 in x 2 in wooden formwork at a depth of 4 in, 8 in, and 12 in. Ready mix concrete was poured into the formwork and 3 concrete cubes were cast with the tags embedded within them. Readers that could be connected to a laptop were used to monitor and collect the time at which these RFID tags can be detected. The test showed that the RFID signals from the low frequency tags at all depths were detected as soon as concrete was poured. The Ultra High Frequency tags placed at the 4" level could be detected 15 minutes after concrete was poured. The UHF tags at the 8" level could be detected after 30 minutes. The UHF tags at the 12" level took on an average 2 hours to be detected from the vicinity of the formwork. The greater the depth at which the ultra high frequency tag was buried the longer it took for it to be detected. The high frequency tags could be detected only at the 4" level. The reason the performance of the HF card degraded in concrete could be because it uses an aluminum foil antenna which is more susceptible to the environment changing the relative permeability. A copper wire antenna could have fared better in this condition, increasing the chances of detecting the tag. Moreover a passive tag was used. The read range and chances of detection could have been increased had an active tag been used. The power of the reader that was used was also very less which might have contributed to the tag not being detected. Among the tags that were used in the experiment it was found that low frequency tags was the tag that could be detected the earliest after concrete was poured into the forms. However, the maximum read range of the tag observed in the experiment was 20" which is too small a distance to be used on an actual construction site.
2

The effects of cement extenders and water to binder ratio on the heat evolution characteristics of concrete

Greensmith, Christopher Graeme 31 October 2006 (has links)
Student Number : 9900772K - MSc research project - School of Civil and Environmental Engineering - Faculty of Engineering and the Built Environment / The hydration of cement is an exothermic reaction, which begins almost immediately upon contact with water. This produces a large amount heat that subsequently raises the temperature of the concrete mixture, creating a temperature gradient across the member. The temperature rise associated with hydration induces thermo-mechanical stresses. These stresses can cause damage to the structure, affecting the durability and in extreme cases the functionality of the structure. If the maximum rate of heat evolution experienced can be minimised through the selection of the constituents of a concrete mixture, then the thermal stresses that develop in the concrete can be reduced. The main aim of this research is to develop a knowledge of how the heat evolution characteristics of concrete are affected by changing certain concrete mixture parameters and ingredients. The focus is on the addition of three different cement extenders and varying the water/cement ratio. This will be a step towards the development of a model for predicting the thermal properties of concrete. As a part of this investigation, a prediction model for the change in heat rate in concrete was developed. The model is intended to predict the contribution of the individual clinker crystallographic phases in cement and the heat liberated in concrete during hydration.

Page generated in 0.0701 seconds