No description available.

Neste trabalho, foi realizado o crescimento de nanotubos de carbono pela técnica de deposição química a vapor (CVD) térmica catalítica, utilizando-se filmes finos de níquel como material catalisador, gás metano (CH4) como fonte de hidrocarboneto e nitrogênio (N2) como gás de arraste. Amostras processadas sobre filmes de Ni de 15 nm de espessura, depositados sobre substrato de óxido de silício (SiO2), com temperatura de processo de 900 ºC e tempo de 15 minutos promoveram uma maior densidade de síntese de nanotubos de carbono, utilizando-se um fluxo na proporção de 2 partes de N2 para 1 parte de CH4. Comprovou-se sua síntese através da visualização de sua morfologia por microscopia eletrônica de varredura (SEM) e microscopia eletrônica de transmissão (TEM), além da extração de seu espectro característico por espectroscopia Raman e espectroscopia de dispersão de raio-X (EDS). Em um segundo estudo, depositaram-se sobre substratos de vidro filmes transparentes e condutores (TCF) à base de nanotubos de carbono de paredes múltiplas (MWCNT) comerciais, pela técnica de dip coating. Para isso, realizou-se a dispersão dos nanotubos sob diversas concentrações em água deionizada (DI) com o auxílio do surfactante dodecil sulfato de sódio (SDS), com posterior funcionalização através do ataque químico por ácido nítrico (HNO3), visando sua aplicação na fabricação de células solares. Foram utilizados os equipamento de quatro pontas e curva corrente x tensão (IV) para caracterização elétrica, transmitância por espectrofotometria para caracterização óptica, SEM para a visualização de sua morfologia e espectroscopia Raman para a análise química de suas estruturas. Valores de resistência de folha de 2x105 W/ e transmitância de 65% foram obtidos nas amostras mais concentradas, com 0,2 mg de nanotubos por ml de água DI. Uma etapa de limpeza em água DI pós deposição foi feita para remoção do excesso de surfactante presente no filme, o que prejudica tanto as características elétricas e ópticas, por ser um dielétrico e não ser transparente. Essa limpeza melhorou o valor de transmitância, porém aumentou a resistência de folha, devido à remoção parcial dos nanotubos presentes no filme, interrompendo em certos pontos a malha que promovia a passagem de corrente elétrica. O ataque químico por HNO3 promoveu a criação de algumas quebras na estrutura do carbono, o que é verificado pelo aumento da banda D, característico da presença de defeitos. / In this work, the growth of CNTs was investigated, using chemical vapor deposition (CVD) thermal catalytic technique, carried out by utilizing thin films of nickel as catalyst material, methane (CH4) as hydrocarbon source and nitrogen (N2) as carrier gas. Samples processed onto 15 nm thick Ni films, deposited on silicon oxide (SiO2) substrates, at a temperature of 900 °C for 15 minutes, promoted a higher density of carbon nanotubes, using a gas mixture at the ratio of 2 parts of N2 and 1 part of CH4. This was verified by analysing the nanotubes morphology by scanning electron microscopy (SEM) and transmission electronic microscopy (TEM) and by the extraction of its characteristic spectrum by Raman spectroscopy and energy dispersive spectroscopy (EDS). In a second study, transparent conductive films (TCF) based on commercial multi-walled carbon nanotubes (MWCNT) were deposited on glass substrates by the dip coating technique. To do so, carbon nanotubes (CNTs) with different concentrations were dispersed in deionized water (DI) with the addition of the surfactant sodium dodecyl sulfate (SDS), and subsequent functionalization through chemical attack by nitric acid (HNO3), aiming their application in solar cell fabrication. The four point probe equipment and current x voltage curve (IV) was used for electrical characterization, transmittance for optical characterization, SEM to visualize their morphology and Raman spectroscopy for chemical analysis of their structures. Sheet resistance values of 2x105 W/ and transmittance of 65% were obtained in the most concentrated samples, with 0.2 mg per ml of nanotubes in deionized water (DI). A cleaning stage in DI water after deposition was taken for removal of surfactant excess in the film, which harms both the electrical and optical characteristics, as it is a dielectric and not transparent. This cleaning improved the transmittance value, but increased the sheet resistance due to partial removal of the nanotubes in the film, interrupting at certain points the mesh of CNTs that promoted the passage of electric current. The chemical attack by HNO3 promoted the functionalization by creating some breaks in the carbon structure, which is checked by the observation of the increasing in D band, which is characteristic of defects.

Neste trabalho, foi realizado o crescimento de nanotubos de carbono pela técnica de deposição química a vapor (CVD) térmica catalítica, utilizando-se filmes finos de níquel como material catalisador, gás metano (CH4) como fonte de hidrocarboneto e nitrogênio (N2) como gás de arraste. Amostras processadas sobre filmes de Ni de 15 nm de espessura, depositados sobre substrato de óxido de silício (SiO2), com temperatura de processo de 900 ºC e tempo de 15 minutos promoveram uma maior densidade de síntese de nanotubos de carbono, utilizando-se um fluxo na proporção de 2 partes de N2 para 1 parte de CH4. Comprovou-se sua síntese através da visualização de sua morfologia por microscopia eletrônica de varredura (SEM) e microscopia eletrônica de transmissão (TEM), além da extração de seu espectro característico por espectroscopia Raman e espectroscopia de dispersão de raio-X (EDS). Em um segundo estudo, depositaram-se sobre substratos de vidro filmes transparentes e condutores (TCF) à base de nanotubos de carbono de paredes múltiplas (MWCNT) comerciais, pela técnica de dip coating. Para isso, realizou-se a dispersão dos nanotubos sob diversas concentrações em água deionizada (DI) com o auxílio do surfactante dodecil sulfato de sódio (SDS), com posterior funcionalização através do ataque químico por ácido nítrico (HNO3), visando sua aplicação na fabricação de células solares. Foram utilizados os equipamento de quatro pontas e curva corrente x tensão (IV) para caracterização elétrica, transmitância por espectrofotometria para caracterização óptica, SEM para a visualização de sua morfologia e espectroscopia Raman para a análise química de suas estruturas. Valores de resistência de folha de 2x105 W/ e transmitância de 65% foram obtidos nas amostras mais concentradas, com 0,2 mg de nanotubos por ml de água DI. Uma etapa de limpeza em água DI pós deposição foi feita para remoção do excesso de surfactante presente no filme, o que prejudica tanto as características elétricas e ópticas, por ser um dielétrico e não ser transparente. Essa limpeza melhorou o valor de transmitância, porém aumentou a resistência de folha, devido à remoção parcial dos nanotubos presentes no filme, interrompendo em certos pontos a malha que promovia a passagem de corrente elétrica. O ataque químico por HNO3 promoveu a criação de algumas quebras na estrutura do carbono, o que é verificado pelo aumento da banda D, característico da presença de defeitos. / In this work, the growth of CNTs was investigated, using chemical vapor deposition (CVD) thermal catalytic technique, carried out by utilizing thin films of nickel as catalyst material, methane (CH4) as hydrocarbon source and nitrogen (N2) as carrier gas. Samples processed onto 15 nm thick Ni films, deposited on silicon oxide (SiO2) substrates, at a temperature of 900 °C for 15 minutes, promoted a higher density of carbon nanotubes, using a gas mixture at the ratio of 2 parts of N2 and 1 part of CH4. This was verified by analysing the nanotubes morphology by scanning electron microscopy (SEM) and transmission electronic microscopy (TEM) and by the extraction of its characteristic spectrum by Raman spectroscopy and energy dispersive spectroscopy (EDS). In a second study, transparent conductive films (TCF) based on commercial multi-walled carbon nanotubes (MWCNT) were deposited on glass substrates by the dip coating technique. To do so, carbon nanotubes (CNTs) with different concentrations were dispersed in deionized water (DI) with the addition of the surfactant sodium dodecyl sulfate (SDS), and subsequent functionalization through chemical attack by nitric acid (HNO3), aiming their application in solar cell fabrication. The four point probe equipment and current x voltage curve (IV) was used for electrical characterization, transmittance for optical characterization, SEM to visualize their morphology and Raman spectroscopy for chemical analysis of their structures. Sheet resistance values of 2x105 W/ and transmittance of 65% were obtained in the most concentrated samples, with 0.2 mg per ml of nanotubes in deionized water (DI). A cleaning stage in DI water after deposition was taken for removal of surfactant excess in the film, which harms both the electrical and optical characteristics, as it is a dielectric and not transparent. This cleaning improved the transmittance value, but increased the sheet resistance due to partial removal of the nanotubes in the film, interrupting at certain points the mesh of CNTs that promoted the passage of electric current. The chemical attack by HNO3 promoted the functionalization by creating some breaks in the carbon structure, which is checked by the observation of the increasing in D band, which is characteristic of defects.

Cette thèse rapporte l’étude des propriétés de films transparents conducteurs obtenus à partir de dispersions de nanotubes de carbone. La formulation des dispersions représente une étape clé dans le but d’obtenir des films homogènes avec de bonnes propriétés électro-optiques. Plus particulièrement, la création d’interactions attractives en solution entre les nanotubes de carbone permet d’une part de modifier le comportement rhéologique des dispersions et d’améliorer leur dépôt en couche mince par enduction. D’autre part, les travaux présentent une étude concernant l’influence des interactions sur la structuration du réseau de nanotube de carbone qui constitue les films. Ces changements de structuration sont notamment mis en parallèle avec les propriétés électriques des films selon leur épaisseur. L’utilisation de polymères semi-conducteurs a aussi fait l’objet de travaux expérimentaux pour améliorer la formation et les propriétés des films transparents conducteurs. / This thesis reports the study of the properties of transparent conductive films obtained from carbon nanotube dispersions. The dispersion formulation is a key step in order to obtain uniform films with good opto-electrical properties. In particular, the formation of attractive interactions between dissolved carbon nanotubes allows the modification of the rheological behavior of the dispersions and the improvement of their deposition in thin layer by coating. Also, the influence of the interactions on the carbon nanotube network morphology is presented. The structural changes of the networks are then related to both electrical properties and thickness of the films. Finally, the use of semiconducting polymers was analyzed in order to improve the fabrication and the properties of transparent conductive films.

A new manufacturing paradigm may lower the cost and environmental impact of existing products, as well as enable completely new products. Large scale, roll-to-roll manufacturing of flexible electronics and other functionality has great potential. However, a commercial breakthrough depends on a lower consumption of materials and energy compared with competing alternatives, and that sufficiently high performance and reliability of the products can be maintained. The substrate constitutes a large part of the product, and therefore its cost and environmental sustainability are important. Electrically conducting thin films are required in many functional devices and applications. In demanding applications, metal films offer the highest conductivity.   In this thesis, paper substrates of various type and construction were characterized, and the characteristics were related to the performance of inkjet-printed metal patterns. Fast absorption of the ink carrier was beneficial for well-defined pattern geometry, as well as high conductivity. Surface roughness with topography variations of sufficiently large amplitude and frequency, was detrimental to the pattern definition and conductivity. Porosity was another important factor, where the characteristic pore size was much more important than the total pore volume. Apparent surface energy was important for non-absorbing substrates, but of limited importance for coatings with a high absorption rate. Applying thin polymer–based coatings on flexible non-porous films to provide a mechanism for ink solvent removal, improved the pattern definition significantly. Inkjet-printing of a ZnO-dispersion on uncoated paper provided a thin spot-coating, allowing conductivity of silver nanoparticle films. Conductive nanoparticle films could not form directly on the uncoated paper.   The resulting performance of printed metal patterns was highly dependent on a well adapted sintering methodology. Several sintering methods were examined in this thesis, including conventional oven sintering, electrical sintering, microwave sintering, chemical sintering and intense pulsed light sintering. Specially designed coated papers with modified chemical and physical properties, were utilized for chemical low-temperature sintering of silver nanoparticle inks. For intense pulsed light sintering and material conversion of patterns, custom equipment was designed and built. Using the equipment, inkjet-printed copper oxide patterns were processed into highly conducting copper patterns. Custom-designed papers with mesoporous coatings and porous precoatings improved the reliablility and performance of the reduction and sintering process.         The thesis aims to clarify how ink-substrate interactions and sintering methodology affect the performance and reliability of inkjet-printed nanoparticle patterns on flexible substrates. This improves the selection, adaptation, design and manufacturing of suitable substrates for inkjet-printed high conductivity patterns, such as circuit boards or RFID antennas.

Perovskit solceller (PSCs) är kända som 'ljusomvandling' enheter med ökad omvandlingseffektivitiet (PCE). PSCs är kända för detta flexibilitet och hög tolerans mot defekter och består av fem lager med olika material och egenskaper. De fem lagren är följande; transparant elektrod, elektron ledande lager (ETL), perovskit lager, hål ledande lager (HTL) och metallelektroden.  Detta forskningsarbete fokuserar på metallelektroden (Cu-tunn film), HTL (CuI-tunn film) och det aktiva lagret (CuI-komplex).  Syftet med denna studie är att undersöka effekten av olika tjocklekar på ytans morfologi och grovhet för att se mängden jod som tränger sig genom filmen genom att beräkna volymen.  Resultatet av denna studie visar att ökad tjocklek leder till ökad grovhet. Man ser även att en ökad tjocklek leder till ett mer homogent och jämn yta, och dessutom ökar kornstorleken, vilket tyder på att kvaliten av kristallisationen förbättras.  Slutligen, genom att känna till tjockleken och storleken (arean) på ytan av proverna kunde man beräkna volymen för att indikera mängden jod som trängt sig genom filmen. Resultatet av denna del indikerade att ju tjockare provet är, desto mer kommer jod att tränga sig genom filmen. / Perovskite solar cells (PSCs) are known as light-harvesting devices with increased power conversion efficiencies (PCE). PSCs are known for their flexibility and high tolerance towards defects. It consists of five different layers with different materials and functions. Transparent electrode, electron transport layer (ETL) , perovskite or active layer , hole transport layer (HTL) and metallic electrode. In this research project, the focus is directed towards the metallic electrode (Cu-thin film), hole transport layer (CuI-thin film) and the active layer (CuI-complex). The purpose of this study is to investigate the effect of different thicknesses on the surface morphology and roughness and to see how much iodine is diffusing through the film by calculating the volume.  The results of this project present that the increase in thickness leads to an increase in roughness. It also shows that an increase in thickness leads to a more homogeneous and uniform surface and in addition the grain size increases which indicates that the quality of crystallization improves. Finally, by knowing the thickness and surface area of the samples the volume was calculated to indicate how much iodine is diffusing through the film and the results for this part indicated that the thicker the sample, more iodine will diffuse through the film.