The quest for multi-standard and software-defined radio (SDR) receivers calls for high flexibility in the receiver building-blocks so that to accommodate several wireless services using a single receiver chain in mobile handsets. A potential approach to achieve flexibility in the receiver is to move the analog-to-digital converter (ADC) closer to the antenna so that to exploit the enormous advances in digital signal processing, in terms of technology scaling, speed, and programmability. In this context, continuous-time (CT) delta-sigma (ΔƩ) ADCs show up as an attractive option. CT ΔƩ ADCs have gained significant attention in wideband receivers, owing to their amenability to operate at a higher-speed with lower power consumption compared to discrete-time (DT) implementations, inherent anti-aliasing, and robustness to sampling errors in the loop quantizer. However, as the ADC moves closer to the antenna, several blockers and interferers are present at the ADC input. Thus, it is important to investigate the sensitivities of CT ΔƩ ADCs to out-of-band (OOB) blockers and find the design considerations and solutions needed to maintain the performance of CT ΔƩ modulators in presence of OOB blockers. Also, CT ΔƩ modulators suffer from a critical limitation due to their high sensitivity to the clock-jitter in the feedback digital-to-analog converter (DAC) sampling-clock. In this context, the research work presented in this thesis is divided into two main parts. First, the effects of OOB blockers on the performance of CT ΔƩ modulators are investigated and analyzed through a detailed study. A potential solution is proposed to alleviate the effect of noise folding caused by intermodulation between OOB blockers and shaped quantization noise at the modulator input stage through current-mode integration. Second, a novel DAC solution that achieves tolerance to pulse-width jitter by spectrally shaping the jitter induced errors is presented. This jitter-tolerant DAC doesn’t add extra requirements on the slew-rate or the gain-bandwidth product of the loop filter amplifiers. The proposed DAC was implemented in a 90nm CMOS prototype chip and provided a measured attenuation for in-band jitter induced noise by 26.7dB and in-band DAC noise by 5dB, compared to conventional current-steering DAC, and consumes 719µwatts from 1.3V supply.

Recently, smart dust or wireless sensor networks are gaining more attention.These autonomous, ultra-low power sensor-based electronic devices sense and process burst-type environmental variations and pass the data from one node (mote) to another in an ad-hoc network. Subsystems for smart dust are typically the analog interface (AI), analog-to-digital converter (ADC), digital signal processor (DSP), digital-to-analog converter (DAC), power management, and transceiver for communication. This thesis project describes an event-driven (ED) digital signal processing system (ADC, DSP and DAC) operating in continuous-time (CT) with smart dust as the target application. The benefits of the CT system compared to its conventional counterpart are lower in-band quantization noise and no requirement of a clock generator and anti-aliasing filter, which makes it suitable for processing burst-type data signals. A clockless EDADC system based on a CT delta modulation (DM) technique is presented. The ADC output is digital data, continuous in time, known as “data token”. The ADC employs an unbuffered, area efficient, segmented resistor-string (R-string) feedback DAC. A study of different segmented R-string DAC architectures is presented. A comparison in component reduction with prior art shows nearly 87.5% reduction of resistors and switches in the DAC and the D flip-flops in the bidirectional shift registers for an 8-bit ADC, utilizing the proposed segmented DAC architecture. The obtained SNDR for the 3-bit, 4-bit and 8-bit ADC system is 22.696 dB, 30.435 dB and 55.73 dB, respectively, with the band of interest as 220.5 kHz. The CTDSP operates asynchronously and process the data token obtained from the EDADC. A clockless transversal direct-form finite impulse response (FIR) low-pass filter (LPF) is designed. Systematic top-down test-driven methodology is employed through out the project. Initially, MATLAB models are used to compare the CT systems with the sampled systems. The complete CTDSP system is implemented in Cadence design environment. The thesis has resulted in two conference contributions. One for the 20th European Conference on Circuit Theory and Design, ECCTD’11 and the other for the 19th IFIP/IEEE International Conference on Very Large Scale Integration, VLSI-SoC’11. We obtained the second-best student paper award at the ECCTD.