Results of this research are available online in two published papers. / The main focus of this research was to synthesize and then to characterize the potential high-performance thermoelectric materials. In this regard, we have prepared a series of pure RECuSe2 (with RE = Pr, Sm, Gd, Dy and Er) and RECuTe2 (with RE = Er, Dy and Gd) and analyzed their crystal structure, electronic and physical properties. We used powder and single crystal X-ray diffraction techniques to analyze their crystal structures and employed energy dispersive X-ray spectrometry (EDS) to verify their chemical compositions. The temperature stability of the synthesized samples was examined by differential thermal and gravimetrical analysis. The high-purity consolidated pellets were prepared for physical properties measurements. We analyzed the relationship between their crystal structures and pertinent electronic properties through the LMTO calculations. The RECuSe2 phases adopt two structures, monoclinic and trigonal. The monoclinic structure (P21/c, z = 4) is observed for lighter rare earths (RE = Pr, Sm and Gd) and Cu-disordered trigonal structure for heavier rare earths (P m1, z = 1, RE = Dy and Er). The resistivity and Seebeck coefficient measurements indicate that the studied selenides are p-type semiconductors with relatively small activation energies (0.045-0.12 eV). However, their electrical resistivities are too high (0.49-220 Ohmcm at room temperature) to make them competitive thermoelectric materials. Electronic structure calculations indicate presence of a band gap in the RECuSe2 phases. The synthesized RECuTe2 phases (RE = Er, Dy and Gd) adopt a monoclinic-distorted variant (C2/m, z = 2) of the trigonal structure (P m1, Z= 1) observed for the RECuSe2 (with RE = Dy, Er). While such disorder may be beneficial for lowering their thermal conductivity, large values of electrical resistivity (0.02-0.87 Ohmcm at room temperature) make these phases unsuitable for practical applications. Comparing to the corresponding semiconducting selenides, the tellurides have lower resistivities, and display a metallic type resistivity. Such behavior stems from the closure of band gaps, which is verified by the electronic structures calculations. Structurally the RECuTe2 phases (with RE = Er, Dy and Gd) are similar to RECuSe2 with the P m1 structure. The monoclinic distortion in RECuTe2 is driven by Cu displacement inside the larger tetrahedral voids in the hexagonal close packing of the Te atoms. Most likely, Cu shifts to one side of the Te tetrahedra to optimize the Cu-Te interactions. / Thesis / Candidate in Philosophy

Silicon nanowires (SiNWs) and the copper chalcogenides, namely copper sulfide (Cu2S) and selenide Cu2Se, have diverse applications in renewable energy technology. For example, SiNWs which have direct band gaps unlike bulk Si, have the potential to radically reduce the cost of Si based photovoltaic cells. However, they degrade quickly under ambient conditions. Various surface passivations have therefore been investigated for enhancing their stability but it is not yet well understood how they affect the electronic structure of SiNWs at a fundamental level. Here, we will explore, from first-principles simulation, how fluorine, methyl and hydrogen surface passivations alter the electronic structures of [111] and [110] SiNWs via strain and quantum confinement. We also show how electronic charge states in [111] and [110] SiNWs can be effectively modelled by simple quantum wells. In addition, we address the issue of why [111] SiNWs are less influenced by their surface passivation than [110] SiNWs. Like SiNWs, Cu2S and Cu2Se also make excellent photovoltaic cells. However, they are most well known for their exceptional thermoelectric performance. This is by virtue of their even more unique solid-liquid hybrid nature which combines the low thermal conductivity and good electrical characteristics required for a high thermoelectric efficiency. We use first-principles molecular dynamics simulations to show that Cu diffusion rates in Cu2S and Cu2Se can be as high as 10-5cm2s-1. We also relate their phonon power spectra to their low thermal conductivities. Furthermore, we evaluate the thermoelectric properties of Cu2S and Cu2Se using a combination of Boltzmann transport theory and first-principles electronic structure calculations. Our results show that both Cu2S and Cu2Se are capable of maintaining high Seebeck coefficients in excess of 200μVK-1 for hole concentrations as high as 3x1020cm-3.

Thermoelectric (TE) materials directly convert heat energy into electrical energy. The conversion efficiency of the TE devices depends on the performance of the materials. The conversion efficiency of available thermoelectric materials and devices is low. Therefore, the development of new materials for improving thermoelectric device performance is a highly essential. As the performance of the TE materials depends on TE figure of merit [zT=S2P T ] which consist of three material properties such as Seebeck coefficient (S), electrical resistivity ( ) and thermal conductivity ( ). Thermoelectric figure of merit can be improved by either increase of power factor or decreasing of thermal conductivity or by both. In the present thesis, Cu based chalcogenide compounds are chosen for the study of thermoelectric properties because of their complex crystal structure, which leads to lower values of thermal conductivity. Also, the power factor of these materials can be tuned by the partial substitution doping. In the present thesis, Cu based chalcogenide compounds quaternary chalcogenide compound (Cu2ZnSnSe4), ternary compounds (Cu2SnSe3 and Cu2GeSe3) and tetrahedrite materials (Cu12Sb4S13) have been prepared by solid state synthesis. The prepared compounds are characterized by XRD for the phase identification, Raman Spectroscopy used as complementary technique for XRD, SEM for surface morphology and EPMA for the phase purity and elemental composition analysis respectively. For the evaluation of zT, thermoelectric properties of all the samples have been studied by measuring Seebeck coefficient, resistivity and thermal diffusivity. In the chapter 1, a brief introduction about thermoelectricity and its effects is discussed. Thermoelectric materials parameters such as electrical resistivity, Seebeck coefficient and thermal conductivity for different class of materials are mentioned. The selection of thermoelectric materials and the motivation for choosing the Cu based chalcogenide compounds for thermoelectric applications are discussed. In chapter 2, the details of the experiments carried out for Cu based chalcogenide compounds are presented. In chapter 3, the effect on thermoelectric properties by the cation substitution on quaternary chalcogenide compound Cu2+xZnSn1 xSe4 (0, 0.025, 0.05, 0.075, 0.1, 0.125, and 0.15) is studied. The electrical resistivity of all the samples decreases with an increase in Cu content except for Cu21ZnSn09Se4, most likely due to a higher content of the ZnSe. All the samples showed positive Seebeck coefficients indicating that holes are the majority charge carriers. The thermal conductivity of doped samples was higher as compared to Cu2ZnSnSe4 and this may be due to the larger electronic contribution and the presence of the ZnSe phase in the doped samples. The maximum zT = 0.23 at 673 K is obtained for Cu205ZnSn095Se4. In chapter 4, the effect of multi{substitution of Cu21ZnSn1 xInxSe4 (0, 0.05, 0.075, and 0.1) on transport properties were studied. The Rietveld powder X-ray diffraction data accompanied by electron probe microanalysis (EPMA) and Raman spectra of all the samples con firmed the formation of a tetragonal kesterite structure. The electrical resistivity of all the samples exhibits metallic-like behavior. The positive values of the Seebeck coefficient and the Hall coefficient reveal that holes are the majority charge carriers. The co-doping of copper and indium leads to a significant increase of the electrical resistivity and the Seebeck coefficient as a function of temperature above 650 K. The thermal conductivity of all the samples decreases with increasing temperature. Lattice thermal conductivity is not significantly modified as the doping content may infer negligible mass fluctuation scattering for copper zinc and indium tin substitution. Even though, the power factors (S2 ) of indium-doped samples Cu21ZnSn1 xInxSe4 (x=0.05, 0.075) are almost the same, the maximum zT=0.45 at 773 K was obtained for Cu21Zn09Sn0925In0075Se4 due to its smaller value of thermal conductivity. In chapter 5, thermoelectric properties of Zn doped ternary compounds Cu2ZnxSn1 xSe3 (x = 0, 0.025, 0.05, 0.075) were studied. The undoped com\pound showed a monoclinic crystal structure as a major phase, while the doped compounds showed a cubic crystal structure confirmed by powder XRD (X-Ray Diffraction). The electrical resistivity decreased up to the samples with Zn content x=0.05 in Cu2ZnxSn1 xSe3, and slightly increased in the sample Cu2Zn0075Sn0925Se3 . This behavior is consistent with the changes in the carrier concentration confirmed by room temperature Hall coefficient data. Temperature dependent electrical resistivity of all samples showed heavily doped semiconductor behavior. All the samples exhibit positive Seebeck coefficient (S) and Hall coefficient indicating that the majority of the carriers are holes. A linear increase in Seebeck coefficient with increase in temperature indicates the degenerate semiconductor behavior. The total thermal conductivity of the doped samples increased with a higher amount of doping, due to the increase in the carrier contribution. The total and lattice thermal conductivity of all samples decreased with increasing of temperature, which points toward the dominance of phonon scattering at high temperatures. The maximum zT = 0.34 at 723 K is obtained for the sample Cu2SnSe3 due to a low thermal conductivity compared to the doped samples. In chapter 6, thermoelectric properties of Cu2Ge1 xInxSe3 (x = 0, 0.05, 0.1, 0.15) compounds is studied. The powder X-ray diffraction pattern of the undoped sample revealed an orthorhombic phase. The increase in doping content led to the appearance of additional peaks related to cubic and tetragonal phases along with the orthorhombic phase. This may be due to the substitutional disorder created by indium doping. The electrical resistivity ( ) systematically decreased with an increase in doping content, but increased with the temperature indicating a heavily doped semiconductor behavior. A positive Seebeck coefficient (S) of all samples in the entire temperature range reveal holes as predominant charge carriers. Positive Hall coefficient data for the compounds Cu2Ge1 xInxSe3 (x= 0, 0.1) at room temperature (RT) con rm the sign of Seebeck coefficient. The trend of as a function of doping content for the samples Cu2Ge1 xInxSe3 with x = 0 and 0.1 agrees with the measured charge carrier density calculated from Hall data. The total thermal conductivity increased with rising doping content, attributed to an increase in carrier thermal conductivity. The thermal conductivity decreases with increasing temperature, which indicates the dominance of Umklapp phonon scattering at elevated temperatures. The maximum thermoelectric figure of merit (zT) = 0.23 at 723 K was obtained for Cu2In01Ge09Se3. In chapter 7, thermoelectric properties of Cu12 xMn1 xSb4S13 (x = 0, 0.5, 1.0, 1.5, 2.0) samples were studied. The Rietveld powder XRD pattern and Electron Probe Micro Analysis revealed that all the Mn substituted samples showed a single tetrahedrite phase. The electrical resistivity increased with increasing Mn due to substitution of Mn2+ on the Cu1+ site. The positive Seebeck coefficient for all samples indicates that the dominant carriers are holes. Even though the thermal conductivity decreased as a function of increasing Mn, the thermoelectric figure of merit (zT) decreased, because the decrease of the power factor is stronger than the decrease of the thermal conductivity. The maximum zT = 0.76 at 623 K is obtained for Cu12Sb4S13. In chapter 8, the summary and conclusion of the present work is presented.