Conjugated organic polymers have attracted immense interest for use in the active layer of photovoltaic cells, electroluminescent displays and diagnostic sensors. Precise control of the chemical structure of these conjugated materials is essential to achieve better device performance and certain structural aspects which have received minimal investigation include; the nature of the end groups, the precise control of the molecular weight and the formation of novel polymer topologies. Absolute control of these factors, in particular the end groups, has the potential to further tune the electro-optical properties, eliminate charge trapping and reactive sites, and facilitate block copolymer formation. The ring opening metathesis polymerisation of highly strained cyclophanediene monomers has proven to be an advantageous route to obtain soluble poly(p-phenylenevinylene)s (PPVs). In an extension of this previous work PPVs with both a pristine polymer backbone microstructure and a range of well-defined functional end groups have been prepared. These polymers exhibited excellent degrees of functionality, relatively narrow unimodal distributions and degrees of polymerisation much higher than those attainable by alternate routes. In particular the incorporation of an α-bromoester end group directly resulted in PPVs which were effective macroinitiators in the atom transfer radical polymerisation of methyl methacrylate. The diblock copolymers prepared by this route were isolated with narrow polydispersities, unimodal distributions and were free from homopolymer impurities. This method of preparing rod-b-coil diblock copolymers, where the properties of the two segments can readily be modified, provides access to materials which are of interest for both their self-assembly ability and for the development of a much required phase diagram in this area. Cyclic PPVs are of synthetic interest both for the absence of any end groups and for an infinitely long π-conjugated backbone, both of which are expected to contribute to unique electro-optical properties. The preparation of these target polymers was investigated by the ring expansion metathesis polymerisation of the cyclophanediene monomers. The formation of purely cyclic, low molecular weight PPVs was found to be highly dependent on both the reaction conditions used and the nature of the solubilising substituents. For example the preparation of purely cyclic PPVs with alkoxy side chains was unsuccessful, however the incorporation of alkyl side chains allowed for the successful isolation of the desired cyclic polymers.

The synthesis of benzo[e]dimethyldihydropyrene (BDHP) photoswitches with ter-27, quarter-36, and quinque-28 thiophene oligomers attached on the same side of the switch was achieved using Stille coupling reactions. BDHP photoswitches with bi-75, ter-76 and quinque-77 thiophene oligomers attached directly to the switch on one side, and via a carbonyl spacer on the opposite side of the switch were also synthesized. Dimethyldihydropyrene (DHP) photoswitches with a naphthoyl functional group in the 2 position were synthesized using a Friedel Crafts reaction, and ter-96, quinque-97 and septi-98 thiophene oligomers were attached on opposite sides of the switch using Stille coupling reactions. All compounds were characterized by NMR, IR UV-vis spectroscopy and mass spectrometry. The relative rates of the photo-opening reactions under excess light conditions and the UV closing reactions versus BDHP were measured. Improvements in the photo-opening properties of the oligothiophene functionalized switches compared to BDHP were observed. The most dramatic photo-opening improvement was found for the quinquethienyl substituted DHP switch 97 which photo-opened when irradiated with visible light over 100 times faster than BDHP. UV closing rates were virtually the same as that of BDHP. However the addition of oligothiophenes led to an increase in the thermal closing reaction rates. Compounds with the naphthoyl functional group in the 2 position of DHP were found to have dramatically increased thermal closing rates. The electrochemical properties of oligothiophene functionalized BDHP and naphthoyl functionalized DHP switches in the closed form were studied by cyclic voltammetry and spectroelectrochemistry. During the oxidation cycle, a closing reaction from the cyclophanediene (CPD) form to the DHP form of the switches occurred which prevented the study of the electrochemical properties of the switches in the open form. Conductivity testing was performed on the quinquethienyl substituted DHP switch 97 using a gold interdigitated micro electrode array. The conductivity of undoped 97 was greater in the closed DHP isomer than in the open CPD isomer. Irradiation with red or blue light allowed for repetitive switching between the more highly conducting closed form and the less conducting open form. When electrochemically doped, 97 showed improved conductivity over the undoped form but only the conductivity of the closed doped form could be measured due to electrochemically induced closing.