Ship roll motion has been the subject of many studies, because of the complexities associated with this mode of ship motion, and its impact on operability, safety, and survivability. Estimation and prediction of the energy transfer and dissipation of the hydrodynamic components, added inertia and damping, is essential to accurately describe the roll motions of a ship. This is especially true for ship operations in moderate to extreme sea conditions. In these conditions, a complex process of energy transfer occurs, which alters the physical behavior of the hydrodynamic components, and ultimately affects the amplitude of ship roll motion. Bilge keels have been used on ships for nearly two centuries, to increase damping and reduce the severity of roll motions experienced by a ship in waves. Because ship motions are more severe in extreme sea conditions, large roll angles may occur. With the possibility of crew injury, cargo damage, or even capsize, it is important to understand the behavior of the roll added inertia and damping for these conditions. Dead ship conditions, where ships may experience excitation from beam, or near beam, seas present a worst case scenario in heavy weather. The behavior of a ship in this condition should be considered in both the design and assessment of seakeeping performance. In this study, hydrodynamic component models of roll added inertia and roll damping were examined and assessed to be unsuitable for accurate prediction of ship motions in heavy weather. A series of model experiments and numerical studies were carried out and analyzed to provide improved understanding of the essential physical phenomena which affect the hydrodynamic components and occur during large amplitude roll motion. These observations served to confirm the hypothesis that the existing models for roll added inertia and damping in large amplitude motions are not sufficient. The change in added inertia and damping behavior for large roll motion is largely due to the effects of hull form geometry, including the bilge keels and topside geometry, and their interactions with the free surface. Therefore, the changes in added inertia and damping must be considered in models to describe and predict roll motions in severe wave environments. Based on the observations and analysis from both experimental and numerical methods, several time-domain model formulations were proposed and examined to model hydrodynamic components of large amplitude roll motions. These time-domain formulations included an analytical model with memory effects, a piecewise formulation, and several possibilities for a bilge keel force model. Although a piecewise model for roll damping was proposed, which can improve the applicability of traditional formulations for roll damping to heavy weather conditions, a further attempt was undertaken to develop a more detailed model specifically for the bilge keel force. This model was based on the consideration of large amplitude effects on the hydrodynamic components of the bilge keel force. Both the piecewise and bilge keel force models have the possibility to enable improved accuracy of potential flow-based numerical prediction of ship roll motion in heavy weather. However, additional development remains to address issues for further practical implementation. / Ph. D.

Le Sous-comité de la conception et de la construction navale de l'Organisation maritime internationale (OMI) a entrepris l'élaboration de critères de stabilité intacts de deuxième génération (SGISC). Le SGISC est une règle supplémentaire qui complète les règles actuelles.En outre, ces critères sont structurés en trois niveaux, à savoir le premier niveau, le deuxième niveau et l'évaluation directe. Les procédures d'évaluation directe pour chaque échec de stabilité sont développées avec la technologie de pointe la plus avancée disponible soit par analyse numérique, soit par travail expérimental pour une analyse quantitative. Dans cette thèse, on présente une implémentation des niveaux 1 et 2 du SGISC dans le solveur hydrostatique, une approche expérimentale pour le navire en détresse dans une tempête et des simulations RANS du même critère. En conclusion, il est possible de mettre en oeuvre les critères de stabilité du navire intact de deuxième génération dans le code de stabilité GHS ©, un code couramment utilisé par les industriels dans le domaine. Cinq navires ont été considérés pour vérifier cette mise en oeuvre. Une méthode expérimentale utilisant une grande soufflerie et une méthode de calcul CFD simplifiée ont été appliquées sur deux modèles. Dans les deux cas, les résultats montrent que l'angle de roulis maximal atteint par les deux navires étudiés est inférieur à celui donné par le calcul réglementaire. La méthode expérimentale est certainement plus proche de la réalité et le calcul CFD reste conservateur sans être aussi contraignant que la réglementation. En conclusion les méthodes expérimentale et numérique développées et utilisées dans ce travail de thèse peuvent être proposées pour l’évaluation directe du critère. / The Sub-Committee of Ship Design and Construction of International Maritime Organisation (IMO) has undertaken the development of Second Generation Intact Stability Criteria (SGISC). The GISC is an additional rule that complement present rules. Five failure modes will be address in SGISC are excessive roll in dead ship condition, pure loss of stability, broaching, parametric roll, and excessive acceleration. Moreover, these criteria are structured in three levels namely, first level, second level and direct assessment. Direct assessment procedures for every stability failure are developed with the most advanced state-of-the art technology available either by numerical analysis or experimental work for quantitative analysis. In this thesis, implementations of Level 1 and Level 2 of the SGISC in the hydrostatic solver, experimental approached for dead ship condition and RANS simulation are presented.In conclusion, it was possible to implement the stability criteria of the intact second-generation vessel in the GHS © code of stability, a code commonly used by industrialists in the field. Five vessels were considered to verify this implementation. An experimental wind tunnel method and a simplified CFD calculation method were used on two different models. In both cases, the results show that the maximum roll angle reached by the two vessels studied is lower than the one given by the regulatory calculation. The experimental method is certainly closer to reality and the calculation CFD remains conservative without being as binding as the regulation.Therefore, the two approaches, numerical and experimental can be proposed to be used for Direct Assessment of the criterion.