Thesis (MEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: Flexible pavement designers have a choice of two wearing course: either asphalt concrete or surfacing seals. The latter have been widely used by several countries as their preferred wearing course over other methods, especially countries with a limited number of average inhabitants per square kilometre. Moreover, the surfacing seals were identified as an efficient cost effective road preventive maintenance technique. Surfacing seals in New Zealand, South Africa and Australia cover about 65%, 80% and 90% of their surfaced road networks respectively. The preference of surfacing seals is due to their competitive initial cost and ease of construction. In South Africa, the life expectancy of surfacing seals varies between 8 and 12 years with an average of 10 years. This has not been the case in a number of surfacing seals constructed in winter, especially when the night recorded temperature is below 10oC. The dominant failure mechanism is ravelling (chip loss) soon after construction due to traffic loading. This chip loss is linked to the poor adhesion bond development rate in the bitumen-aggregate system during winter adverse conditions. In order to address the issue of premature chip loss the need for the development of a robust adhesion test method was identified. For that purpose, recently, researchers in the bitumen industry developed the Bitumen Bond Strength test method. This method was used in this study. This study intends to contribute to the understanding of binder-aggregate adhesion bond development for winter surfacing seals using the BBS test. Binder type, precoat type and conditioning, aggregate type and curing time are amongst the factors influencing winter seals adhesion bond performance. An experimental matrix involving three types of binder, two types of aggregate, four different precoating fluids, two precoat conditionings and two binder-curing times were then developed and investigated. Winter weather parameters affecting adhesion properties were also taken into consideration during the course of the investigation. Throughout the test, the procedure described in AASHTO TP 91-11 was followed. However, in order to enhance the control of the binder application temperature, a new method for hot applied binder sample preparation was developed as part of this study. The findings show that there is a significant difference between adhesion properties of the hot applied binders (70/100 and S-E1) and the emulsion (SC-E1). In most of the cases, the hot applied binders performed better than the emulsion. The failure mode observed was found to be linked to the condition of the precoating. The influence of the precoat type and conditioning, and effect of binder curing time were significantly highlighted. The use of a dry precoat benefited the adhesion bond strength up to around 50% relatively to the corresponding non-precoated combination. However, a decrement in the bond strength due to precoating of up to 28.7% was also observed. A statistical analysis using ANOVA did not illustrate any statistical significant effect of the aggregate type. The interaction effects analysis using ANOVA revealed the aggregate type interacting with precoat type to be the most influential interaction at level two. The precoat conditioning implication to the adhesion development rate, which influences the time for opening to traffic after construction, was illustrated. Insightful aspects on the compatibility between the binder type and precoat type and conditioning during the aggregate precoating practices and on the time for opening to traffic are highlighted. Finally, the repeatability analysis proved the BBS test to be a repeatable testing method with caution. Recommendations for further studies that could support the conclusions drawn in this study were provided. / AFRIKAANSE OPSOMMING: Buigbare plaveiselontwerpers het 'n keuse van twee deklae: óf Asfalt of oppervlak seëls. Laasgenoemde word algemeen gebruik deur verskeie lande as hul voorkeur deklaag, veral die lande met beperkte aantal gemiddelde inwoners per vierkante kilometer. Verder, is die seëls geïdentifiseer as 'n doeltreffende koste-effektiewe deklaag tegniek. Oppervlakseëls in Nieu-Seeland, Suid-Afrika en Australië dek ongeveer 65%, 80% en 90% van hul padnetwerke onderskeidelik. Die seëls se voorkeur is te danke aan hul mededingende aanvanklike koste en eenvoudige vorm van die konstruksie. In Suid-Afrika wissel die seël se lewensverwagting tussen 8 en 12 jaar met 'n gemiddeld van 10 jaar. Dit is egter nie die geval van 'n aantal seëls wat in die winter gebou word nie, veral wanneer die aangetekende nagtemperatuur onder 10o C daal nie. Die dominante swigtingsmeganisme is stroping (klipverlies) kort na konstruksie. Hierdie klipverlies is gekoppel aan die power kleef-ontwikkeling van bitumen gedurende die winter. Ten einde die probleem van voortydige klipverlies aan te spreek het die behoefte vir die ontwikkeling van 'n robuuste toetsmetode ontstaan. Om hierdie rede het navorsers onlangs in die bitumenbedryf die “BBS toetsmetode” ontwikkel en is dié toetsmetode in hierdie studie gebruik. Hierdie studie beoog om by te dra tot die begrip van bindmiddel-klip kleefontwikkeling vir die winter seëls dmv die BBS toets. Die faktore, insluitend maar nie beperk tot bindmiddeltipe, voorafdekking (“PRECOAT”) -tipe en kondisionering, aggregaattipe en kuurtyd beïnvloed winter seëls se kleefeienskappe. 'n Eksperimentele matriks met drie tipes bindmiddels, twee tipes aggregate, vier verskillende voorafdekking-vloeistowwe, twee voorafdekking kondisionering en twee bindmiddel kuurtye is toe ontwikkel en ondersoek. Winter weer parameters wat kleefeienskappe beïnvloed is ook in ag geneem tydens die verloop van die ondersoek. Regdeur die studie is die prosedure AASHTO TP 91-11 gevolg, maar ten einde die beheer van die bindmiddel spuittemperatuur te verbeter, is ‘n nuwe metode vir warmspuit-bindmonsters voorbereiding ontwikkel as deel van hierdie studie. Die bevindinge toon dat daar 'n beduidende verskil tussen die kleefeienskappe van die warm aangewende bindmiddels (70/100 en S-E1) en die emulsie (SC-E1) is. In die meeste van die gevalle het die warmspuit-bindmiddels beter as emulsie gevaar. Daar is gevind dat die swigtingsmeganisme verbind word met die toestand van die voorafdekking. Die invloed van voorafdekkingtipe, kondisionering, en die effek van bindmiddelkuurtyd is duidelik uitgelig. Die gebruik van droë voorafdekking het die kleefkrag tot sowat 50% verhoog relatief tot die ooreenstemmende onbedekte klipkombinasie. Daar is egter ook ‘n verlaging van die kleefkrag weens voorafdekking gevind van tot so hoog soos 28,7 persent. Die statistiese ontleding met behulp van ANOVA het geen statisties beduidende effek van die verksillende aggregaattipe te vore gebring nie. Die interaksie-effek analise, met behulp van ANOVA, het wel die interaksie met voorafdekkingtipe met aggregaat die mees invloedryke bevestig. Die voorafdekking kondisioneering het ver rykende kleefkrag implikasies bloot gelê, wat die tyd vir die opening van die verkeer na konstruksie beïnvloed. Insigwekkende aspekte oor die versoenbaarheid tussen die bindmiddeltipe, voorafdekkingtipe, kondisionering, voorafdekkingpraktyk en tyd tot opening vir verkeer word uitgelig. Ten slotte, die herhaalbaarheidsanalise het die BBS toets as 'n herhaalbare toetsmetode met omsigtigheid bewys. Daar is aanbevelings tot verdere studies, wat uit die gevolgtrekking gekom het, gemaak.

Thesis (MEng)–Stellenbosch University, 2014. / ENGLISH ABSTRACT: The Port of Durban is forecasted to reach its capacity in terms of container handling soon, which necessitates the investigation of an alternative port in the vicinity. The old Durban Airport site has been identified as a potential location to develop a new deep water container harbour. This is driven by a demand for deep water berth capacity as a result of shipping liners preferring the benefits of scale in their operations, leading to the use of larger ships with deeper drafts. To protect the new port from wave energy penetrating inside the basin as well as from sedimentation from the adjacent beaches, the design and construction of breakwaters are required. The proposed main breakwater for this dig-out port is expected to extend 1 200m into the sea, up to depths of 30m at the seaward roundhead. The deeper parts of the breakwater face wave onslaught in a different manner than a conventional breakwater in shallower waters. At these larger depths, the breakwater has to dissipate the energy of non-breaking waves. In this thesis, the wave climate nearshore, adjacent to the proposed breakwater is studied and extreme wave events are simulated with a SWAN numerical model. The results for a range of wave conditions, corresponding to selected events up to a return period of one in 100 years, are presented. A study of deep water breakwaters was undertaken to investigate other examples of similar structures. This indicated a clear distinction between vertical wall type breakwaters and the more traditional rubble-mound type breakwaters. For this thesis, a rubble-mound breakwater was chosen as the breakwater type for testing under conditions of the Durban Dig-Out Port (DDOP). Focussing on a deep water trunk section of the proposed main breakwater, a concept cross-section was designed using deterministic design methods. The formulae incorporated in this method did however not take into account the packing density of the armour layer and only assumed the recommended values. The hypothesis is thus put forward that the breakwater will still be hydraulically stable for packing densities below the recommended values. This would decrease material consumption and save on cost over the entire breakwater. A physical model was designed to experiment with different armour layer configurations of single- and double layer Cubipod arrangements. The unit was chosen for its massive shape and structural integrity even during impact. A physical model study was performed at the facilities of the CSIR in Stellenbosch. It entailed setting up a fixed-bed two-dimensional physical model in a glass wave flume. Measuring wave heights, wave reflection, overtopping, wave transmission and armour damage, the hydraulic stability and operational performance were analysed for several tests. Based on the results of the first few test series, alterations were made to the breakwater geometry and armouring. The results confirmed the hypothesis that lower packing densities were still hydraulically stable under 1 in 100 year return period wave conditions without inhibiting operational performance. A final cross-section is presented as concept design for the deep section of the proposed DDOP main breakwater. / AFRIKAANSE OPSOMMING: Volgens vooruitsigte gaan Durban hawe binnekort sy kapasiteit bereik wat die hantering van skeepshouers betref. Hierdie verwikkeling noodsaak die ondersoek na ‘n alternatiewe hawe in die nabye omgewing. Die voormalige Durban lughawe is intussen geïdentifiseer as ‘n potensiële perseel waar ‘n diep water houervrag hawe ontwikkel kan word. Dit word gedryf deur die aanvraag na diep water kaai kapasiteit as gevolg van skip operateurs wat skaalvoordele verkies, sodat groter skepe met diep rompe meer populêr word. Die ontwerp en konstruksie van breekwaters word dus benodig, om te verhoed dat beide golwe, sowel as sediment van aangrensende strande, die hawe binnedring. Die voorgestelde hoof breekwater vir hierdie hawe sal na verwagting tot 1200m in die see in strek, waar dit tot 30m diep is naby die seewaartse hoof van dié breekwater. Die dieper gedeeltes van só ‘n breekwater sal blootgestel word aan ‘n ander soort golf aanslag as ‘n soortgelyke konvensionele breekwater in vlakker water. In hierdie waterdiepte is die breekwater verantwoordelik vir die energie verbreking van ongebreekte golwe. In hierdie tesis word die golfklimaat langs die kus, naby aan die voorgestelde breekwater bestudeer. Die uiterste golf gebeurtenisse word gesimuleer met ‘n SWAN numeriese model. Die resultate van ‘n reeks golf kondisies, ooreenstemmend met bepaalde gebeurtenissemet herhaal periodes van tot 100 jaar, word aangebied. ‘n Studie van diep water breekwaters is onderneem om voorbeelde van soortgelyke strukture te ondersoek. Die studie toon ‘n definitiewe onderskeid tussen vertikale muur breekwaters en die meer tradisionele “rubble-mound” breekwater tipes. Vir hierdie tesis is die “rubble-mound” breekwater tipe gekies vir toetsing, onderhewig aan die kondisies van die “Durban Dig-Out Port” (DDOP). ‘n Konsep deursnit is ontwerp vir ‘n diep water romp gedeelte van die voorgestelde hoof breekwater, deur van deterministiese metodes gebruik te maak. Die formules soos vervat in hierdie proses maak egter nie voorsiening vir die pakdigtheid van die bewapeningslaag nie, maar aanvaar slegs die voorgestelde waardes. Die hipotese word dus aangevoer dat die breekwater steeds hidrolies stabiel sal wees vir pakdigthede wat laer as die voorgestelde waardes is. Dit sal die verbruik van materiale verlaag en lei tot koste besparings vir die breekwater. ‘n Fisiese model is ontwerp om te eksperimenteer met verskillende opstellings van die bewapeningslaag. Dit sluit enkel- en dubbel laag bewapening met Cubipod eenhede in. Hierdie eenheid is gekies vir sy massiewe vorm en strukturele integriteit, selfs tydens impak. ‘n Fisiese model studie is uitgevoer by die fasiliteite van die WNNR in Stellenbosch. Dit het die opstel van ‘n vaste-bodem, twee-dimensionele fisiese model in ‘n glas golftenk (“wave flume”) behels. Hidroliese stabiliteit en operasionele werksverrigting is geanaliseer deur golf hoogtes, -weerkaatsing, -oorslag, -deurlating, en skade aan die bewapening te meet vir verskeie toetse. Gebasseer op die resultate van die eerste paar toetsreekse, is veranderinge gemaak aan die breekwater se geometrie en bewapening. Die resultate het die hipotese bevestig dat laer pakdigthede steeds hidrolies stabiel is tydens golf kondisies met ‘n 1 in 100 jaar herhaal periode, sonder om die werksverrigting van die breekwater te belemmer. ‘n Finale deursnit word voorgestel as ‘n konsepontwerp vir die diep water deursnit van die DDOP se hoof breekwater.

Thesis (MEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: The Swartvlei estuary and lake system is situated on the southern coast of the Western Cape Province of South Africa and forms part of the core conservation area of the Wilderness National Park. The Swartvlei system comprises two interlinked water bodies, namely Swartvlei Lake and Swartvlei estuary. SANParks have been monitoring this estuary closely over the past two decades, due to its importance to the ecology and to tourism. There are also low-lying properties on the perimeter of the Swartvlei estuary which run the risk of occasional flooding. Two of the major monitoring issues in this estuary system are the water level required for successful mouth breaching, and the influence of the water level on the low-lying properties. This study presents a preliminary analysis of the sediment budget across the Swartvlei estuary mouth. The objective of this study was to identify the various sediment contributory factors and to estimate the quantities that each individually contributed towards the defined sediment budget. / AFRIKAANSE OPSOMMING: Die Swartvlei meer en see monding is geleë aan die kaapse suidkus van Suid- Afrika. Dit vorm deel van die kern bewarings area van die Wilderness Nationale Park. Die Swartvlei sisteem bestaan uit twee verbinde, kern dele nl: Swartvlei meer en estuarium. Vir die afgelope twee dekades is hierdie area onder die noue toesig van SANParke as gevolg van die belangrikheid van die area met betrekking tot toerisme en ekologie. Daar is ook menigde laag liggende eiendomme aan die oewers, wat baie sensitief is vir watervlak stygings. Die optimum water vlakke benodig vir die uitskuring van die gety monding het ook implikasies vir die laag liggende eiendome en vereis noukeurige monitering. ‘n Voorlopige analise van die sediment begroting rondom die gety monding word deur hierdie studie voorgelê.