No description available.

The design of dyes for NiO-based dye-sensitized solar cells (DSSCs) has drawn attention owing to their potential applications in photocatalysis and because they are indispensable for the development of tandem dye-sensitized solar cells. The understanding of the electron transfer mechanisms and dynamics is beneficial to guide further dye design and further improve the performance of photocathode in solar cells and solar fuel devices. Time-resolved spectroscopy techniques, especially femtosecond and nanosecond transient absorption spectroscopy, supply sufficient resolution to get insights into the charge transfer processes in p-type dye sensitized solar cell and solar fuel devices. In paper I-V, several kinds of novel organic “push-pull” and inorganic charge transfer dyes for sensitization of p-type NiO, were systematically investigated by time-resolved spectroscopy, and photo-induced charge transfer dynamics of the organic/inorganic dyes were summarized. The excited state and reduced state intermediates were investigated in solution phase as references to confirm the charge injection and recombination on the NiO surface. The charge recombination kinetics is remarkably heterogeneous in some cases occurring on time scales spanning at least six orders of magnitude even for the same dye. In this thesis, we also proposed a novel concept of solid state p-type dye sensitized solar cells (p-ssDSSCs) for the first time (paper VI), using an organic dye P1 as sensitizer on mesoporous NiO and phenyl-C61-butyric acid methyl ester (PCBM) as electron conductor. Femtosecond and nanosecond transient absorption spectroscopy gave evidence for sub-ps hole injection from excited P1 to NiO, followed by electron transfer from P1●- to PCBM. The p-ssDSSCs device showed an impressive 620 mV open circuit photovoltage. Chapter 6 (paper VII) covers the study of electron transfer mechanisms in a covalently linked dye-catalyst (PB-2) sensitized NiO photocathode, towards hydrogen producing solar fuel devices. Hole injection from excited dye (PB-2*) into NiO VB takes place on dual time scales, and the reduced PB-2 (PB-2●-) formed then donates an electron to the catalyst unit.  The subsequent regeneration efficiency of PB-2 by the catalyst unit (the efficiency of catalyst reduction) is determined to ca. 70%.

Grätzel cells or Dye-Sensitized Solar Cells (DSSCs) are considered one of the most promising methods to convert the sun's energy into electricity due to their low cost and simple technology of production. The Grätzel cell is based on a photosensitizer adsorbed on a low band gap semiconductor. The photosensitizer can be a metal complex or an organic dye. Organic dyes can be produced on a large scale resulting in cheaper dyes than complexes based on rare elements. However, the performance of Grätzel cells based on metal-free, organic dyes is not high enough yet. The dye's performance depends primarily on the electron dynamics. The electron dynamics in Grätzel cells includes electron injection, recombination, and regeneration. Different deactivation processes affect the electron dynamics and the cells’ performance. In this thesis, the electron dynamics was explored by various time-resolved spectroscopic techniques, namely time-correlated single photon counting, streak camera, and femtosecond transient absorption. Using these techniques, new deactivation processes for organic dyes used in DSSCs were uncovered. These processes include photoisomerization, and quenching through complexation with the electrolyte. These deactivation processes affect the performance of organic dyes in Grätzel cells, and should be avoided. For instance, the photoisomerization can compete with the electron injection and produce isomers with unknown performance. Photoisomerization as a general phenomenon in DSSC dyes has not been shown before, but is shown to occur in several organic dyes, among them D149, D102, L0 and L0Br. In addition, D149 forms ground state complexes with the standard iodide/triiodide electrolyte, which directly affect the electron dynamics on TiO2. Also, new dyes were designed with the aim of using ferrocene(s) as intramolecular regenerators, and their dynamics was studied by transient absorption. This thesis provides deeper insights into some deactivation processes of organic dyes used in DSSCs. New rules for the design of organic dyes, based on these insights, can further improve the efficiency of DSSCs.

Nano-structured materials are widely applied for various applications like photovoltaics, electrochromics and sensors. A challenging task in all these fields is the functionalization of these materials with a molecule of interest for the desired application. This work demonstrate the post grafting of the most important and commonly used nano-structured material, mesoporous TiO2, with different bifunctional molecular linkers. These compounds basically have two functional groups, the phosphonic acid group which coordinates to the TiO2 surface and a positive and negative head group which controls the surface charge and the potential interaction of the surface with species in solution. These two groups are systematically separated by alkyl group of different chain length which controls the hydrophobicity of the surface. It is shown that the new surface modification technique simplifies the molecular requirements for functional surface modifiers considerably. Using a limited set of organic anchors with adjustable head group charge and hydrophobicity, broad range of molecules can be adsorbed onto TiO2. Different applications based on such modified surfaces were explored and demonstrated. The modified surfaces can be used to incorporate different charged guest molecules, electrochromophores and dyes which enable to probe their electrochemistry and photovoltaic properties on the surface. Supra-molecular self assembly inside the modified pores is possible which can be monitored by different methods. The study includes the prepartaion of the modified surfaces and their characterization using different electrochemical methods, FTIR spectroscopy, Quartz Crystal Microbalance, Contact angle and Scanning Electron Microscopy measurements.

Τα φωτοβολταϊκά στοιχεία με ευαισθητοποίηση χρωστικής (Dye Sensitized Solar Cells, DSSCs) κίνησαν το ενδιαφέρον της επιστημονικής κοινότητας ύστερα από την πρωτότυπη δημοσίευση του 1991 των Grätzel και O' Regan. Προτάθηκαν ως μία φθηνή εναλλακτική λύση σε σύγκριση με τα συμβατικά ηλιακά στοιχεία από άμορφο πυρίτιο (amorphous silicon). Οι κύριοι παράγοντες που οδήγησαν την επιστημονική κοινότητα να στραφεί προς αυτή την κατεύθυνση ήταν η ευκολία σύνθεσης των χρωστικών με σχετικά απλές χημικές διαδικασίες και η λειτουργία των νέων αυτών φωτοβολταϊκών στοιχείων υπό συνθήκες διάχυτου φωτός. Γενικά, ένα τέτοιο φωτοβολταϊκό στοιχείο αποτελείται από μία φωτοάνοδο (photoanode), ένα πορώδες υπόστρωμα από ημιαγώγιμο οξείδιο μετάλλου (metal oxide semiconducting film), μία χρωστική που χρησιμοποιείται ως φωτοευαισθητοποιητής (sensitizer), έναν ηλεκτρολύτη (electrolyte) και ένα αντιηλεκτρόδιο (counter electrode), το οποίο, συνήθως, επικαλύπτεται με ένα λεπτό στρώμα από πλατίνα (Pt). Η κύρια διεργασία που λαμβάνει μέρος σε ένα DSSC, μετά από την απορρόφηση φωτός, είναι μία διεπιφανειακή μεταφορά φορτίου (interfacial electron transfer IET) από την ηλεκτρονιακά διεγερμένη στάθμη της χρωστικής προς τη ζώνη αγωγιμότητας του ημιαγωγού. Η χρονική της διάρκεια είναι της τάξεως των μερικών εκατοντάδων fs και κατατάσσεται στα υπερταχέα φαινόμενα. Ο όρος που έχει επικρατήσει, για τη διεργασία αυτή στα DSSCs, είναι έκχυση ηλεκτρονίων (electron injection) και χρησιμοποιείται στην παρούσα διπλωματική εργασία. Η τεχνική της φασματοσκοπίας φθορισμού χρονικής ανάλυσης με παλμούς διάρκειας μερικών δεκάδων fs, αποτελεί μία από τις πιο αξιόπιστες και άμεσες τεχνικές για την καλύτερη δυνατή καταγραφή υπερταχέων φαινομένων, όπως η έκχυση ηλεκτρονίων. Σκοπός της παρούσας διπλωματικής εργασίας είναι η μελέτη της έκχυσης ηλεκτρονίων με τη χρήση δύο νέων οργανικών χρωστικών, της μορφής D-π-A, ως φωτοευαισθητοποιητές σε DSSCs με την τεχνική αυτή.Στο πρώτο κεφάλαιο πραγματοποιείται μία γενική επισκόπηση των βασικών αρχών που διέπουν τα φωτοβολταϊκά στοιχεία με ευαισθητοποίηση χρωστικής. Αρχικά, γίνεται αναφορά στα μέρη που αποτελούν ένα τέτοιο φωτοβολταϊκό στοιχείο και ακολούθως στα υλικά και στις διεργασίες οι οποίες συμμετέχουν σε ένα ολοκληρωμένο DSSC.Στο δεύτερο κεφάλαιο επιχειρείται, στο πρώτο σκέλος, μία γενική ανασκόπηση της θεωρίας του Markus για τη μεταφορά των ηλεκτρονίων (Markus Theory). Έπειτα, πραγματοποιείται μία αναλυτική επισκόπηση της δυναμικής και κινηματικής των διεργασιών που συντελούνται στα DSSCs. Συνεχίζοντας στο τρίτο κεφάλαιο, παρουσιάζονται πληροφορίες σχετικές με τα υποστρώματα και τις χρωστικές που χρησιμοποιούνται στα DSSCs. Το κεφάλαιο επικεντρώνεται στην περιγραφή των υποστρωμάτων TiO2 και ΖnO, τα οποία αποτελούν τα κύρια υποστρώματα που χρησιμοποιούνται στα DSSCs. Στο δεύτερο σκέλος του κεφαλαίου, πραγματοποιείται αναφορά στις ιδιότητες που οφείλουν να πληρούν οι χρωστικές, για τη χρήση τους στα DSSCs, καθώς και εκτενής ανασκόπηση των χρωστικών, οι οποίες έχουν χρησιμοποιηθεί, μέχρι σήμερα, ως φωτοευαισθητοποιητές. Στο τέταρτο κεφάλαιο παρουσιάζονται οι μηχανισμοί που συμμετέχουν κατά την αποδιέγερση ενός οργανικού μορίου και οι χρονικές κλίμακες, που αυτοί εμφανίζονται (διάγραμμα Jablonski). Επίσης, γίνεται αναφορά στις πληροφορίες που εξάγονται από τα φάσματα σταθερής κατάστασης (steady state spectra) και χρονικής ανάλυσης (time-resolved spectra), καθώς και η μεταξύ τους σύγκριση. Στο πέμπτο κεφάλαιο πραγματοποιείται μία αναλυτική περιγραφή της πειραματικής διάταξης, η οποία χρησιμοποιήθηκε για την εξαγωγή των πειραματικών δεδομένων. Τέλος, στα τελευταία δύο κεφάλαια (πέμπτο και έκτο) περιγράφεται, στο πρώτο, ο φωτοφυσικός χαρακτηρισμός των δύο νέων οργανικών χρωστικών, ΜΖ-173 και ΜΖ-175, της δομής D-π-Α, σε διάλυμα THF και σε στερεό υπόστρωμα TiO2 αντίστοιχα, το οποίο χρησιμοποιήθηκε ως το υπόστρωμα προσρόφησης των χρωστικών. Ακολούθως, μελετήθηκε η δυναμική και η απόδοση της έκχυσης των ηλεκτρονίων από τις χρωστικές αυτές προς το ημιαγώγιμο υπόστρωμα TiO2, με χρήση της τεχνικής της φασματοσκοπίας χρονικής ανάλυσης φθορισμού με παλμούς διάρκειας μερικών δεκάδων fs (femtosecond time resolved fluorescence spectroscopy). Ως δείγμα αναφοράς, για την εύρεση της απόδοσης της έκχυσης των ηλεκτρονίων στη ζώνη αγωγιμότητας του ημιαγωγού, χρησιμοποιήθηκε νανοκρυσταλλικό υπόστρωμα Al2O3. Τέλος, πραγματοποιήθηκε η μελέτη της δυναμικής της έκχυσης των ηλεκτρονίων με τη χρήση του μορίου CDCA, ως συνπροσροφητή στην επιφάνεια των υποστρωμάτων TiO2 και Al2O3, μαζί με χρωστική ΜΖ-173, σε διάφορες συγκεντρώσεις. Αυτή η μελέτη έγινε με σκοπό τη μείωση της συσσωμάτωσης των μορίων της χρωστικής, αφού το μόριο CDCA έχει την ιδιότητα, λόγω της δομής του, να κρατά σε απόσταση τα μόρια της χρωστικής. / Dye-sensitized solar cells (DSSCs) have attracted great scientific interest after the first demonstration of Grätzel and O’Regan in 1991. They were proposed as low cost alternatives to the conventional amorphous silicon solar cells. The key factors which led the scientific community to this direction are the simplicity of their fabrication procedures with mild chemical processes and their operation under ambient conditions of diffused light. Generally, a DSSC consists of a photoanode, a nanostructured metal oxide semiconducting film, a dye sensitizer, an electrolyte and a counter electrode which is usually coated with Pt. The fundamental process that takes place in a DSSC, after the absorption of a photon by the dye, is an interfacial electron transfer (IET) from the dye’s electronically excited state to the semiconductor’s conduction band (CB), taking place within a few hundred femtoseconds. The term which is generally used for this process in DSSCs is electron injection. Ultrafast fluorescence upconversion spectroscopy is one of the most precise and direct techniques for the study and interpretation of such phenomena. The main subject of this master thesis is the presentation of two novel synthesized organic dyes with D-π-A structure and their study as photosensitizers for DSSCs. It is focused on the photophycical properties of these two dyes in solution and on titanium dioxide (TiO2) substrate, which is used as the metal oxide semiconducting film, and especially on the dynamics of electron injection process from the dye’s excited state to the conduction band of the TiO2 with the aforementioned technique. Finally, the electron injection dynamics of one of dyes with coadsorption of co-adsorbers also investigated. This type of molecules can decrease the amount of aggregates penetrating among the dye molecules but on the same time they cause a decrease of the total amount of the adsorbed dye molecules.

No description available.

In recent years, there has been an increasing interest on renewable energy sources as substitute to fossil fuels. Among various processes of energy generation, electrochemical methods such as storage and conversion systems, electrolysis of water (production of H2 and O2), fuel cells, batteries, supercapacitors and solar cells have received great attention. The core of these energy technologies is a series of electrochemical processes, which directly depend on the nature of ‘electro catalyst’. The design and preparation of an electro catalyst is based on new concepts such as controlled surface roughness, atomic topographic profiles, defined catalytic sites, atomic rearrangements, and phase transitions during electrochemical reactions. Good electro catalysts should possess low over potential, high exchange current density, high stability, low cost and high abundance. The most fundamental reactions in the area of electrochemistry are hydrogen evolution (HER) and oxygen reduction (ORR) reactions. They are important in different energy systems such as fuel cells and batteries. Platinum has been a favoured electro catalyst due to its high activity, favourable density of states at Fermi level and chemical inertness. The low abundance, however, limits its large scale applications. Alternate materials with high catalytic activities are always required. In this particular direction, metal chalcogenides such as sulphides and selenides have attracted attention in recent years. The present thesis describes the synthesis of different phases of palladium and nickel chalcogenides and their applicability in various electrochemical reactions, both in aqueous and organic media. First part includes the synthesis of highly crystalline palladium selenide phases namely Pd17Se15, Pd7Se4 and Pd4Se by employing facile single source molecular precursor method. Pure palladium selenide phases are prepared by thrombolysis of highly processable intermediate complexes formed from metal and selenium precursors. Continuous films of different dimensions on various substrates (glass, ITO, FTO etc.) could be prepared (figure 1). This is one of the requirements for processing any new material. Thickness of the films could be altered by changing the volume of precursor complex coated on the substrate. All the phases are found to be metallic in nature with resistivity values in the range of 30 to 180 µΩ.cm. Figure 1. (a) Scanning electron micrograph and (b) photographic image of Pd17Se15 prepared on different substrates glass (1), Si (2), fluorine doped tin oxide (FTO) (3) and DSSC solar cell fabricated using FTO coated Pd17Se15 as the counter electrode (4). Other components of DSSC are given in the experimental section. All the palladium selenides phases are shown to be catalytically active towards electrochemical reactions such as HER and ORR. It is observed that the activities of the phases depend on the stoichiometric ratio of palladium to selenium. Higher the palladium content in the phase, higher is the catalytic activity observed. Therefore, the activities of the chalcogenides can be easily tuned by varying the ratio of metal to chalcogen. Tafel slopes of 50–60 mV/decade are observed for all three phases towards HER indicating that Volmer- Heyrovsky mechanism is operative. The exchange current densities are in the range of 2.3 x 10-4 A cm-2 to 6.6 x 10-6 A cm-2 (figure 2a). Figure 2. (a) Linear sweep voltammograms of Pd17Se15, Pd7Se4 and Pd4Se in 0.5 M H2SO4 (HER) and (b) 0.1 M KOH (ORR) at a scan rate of 2 mVs-1. These phases are found to be highly robust and stable under different pH conditions. Stability of the phases is confirmed by characterizing the catalysts post-HER process, using various techniques such as XPS, XRD and SEM. High activities observed for Pd4Se is explained based on electrochemically active surface area values determined from under potential deposition studies and also based on DFT calculations. Computational studies reveal the presence of different charge distribution on palladium in all the three phases which is likely to be another reason for varied activities. Palladium selenides are also explored as catalysts towards ORR in alkaline medium. Kinetic parameters and reaction mechanism are determined using RDE studies. All the three phases are found to be active and Pd4Se shows the highest activity, following a direct 4 electron reduction pathway (figure 2b). Other two phases follow 2 electron pathway terminating at hydrogen peroxide stage. Catalytic activity of Pd17Se15 is further improved by Nano structuring of the material and by synthesizing the material on active supports such as rGO, acetylene black and today carbon. ORR plays an important role in metal-air batteries. The palladium chalcogenides are used as electrodes in metal-air batteries. Specific energy density observed in the case of Mg-air primary batteries is higher for Pd4Se than the other two phases (figure 3a). Figure 3. (a) Discharge curves of Mg-O2 battery with different phases of palladium selenides as cathodes. Constant current density of 0.5 mA cm-2 is used for discharge. (b) Characteristic J–V curves of DSSCs with Pd17Se15, Pd7Se4 and Pt as counter electrodes. Versatility of these phases is further studied towards redox reaction in non-aqueous medium (I3-/I-). This reaction plays a crucial role in the regeneration of the dye in dye-sensitized solar cells (DSSC). Palladium selenide phases prepared on FTO plates are employed as counter electrodes in DSSC. The solar light conversion efficiencies are found to be 7.45 and 6.8% for Pd17Se15 and Pd7Se4 respectively and are comparable to that of platinum (figure 3b). The reason for high activities may be attributed to high electronic conductivity and low work function of the phases. The following chapter deals with the synthesis of palladium sulphide phases (Pd4S and Pd16S7) using both hydrothermal and single source precursor methods. Electro catalytic activities of the phases are shown towards HER and ORR and Pd4S exhibits better catalytic activities than that of Pd16S7 phase. Direct electrochemistry of cytochrome c is achieved on Pd4S with ∆E of ~64 mV (figure 4a). Electrochemical oxidation of ethanol, ethylene glycol (EG) and glycerol are also studied on the Pd4S phase and the activity is found to follow the order, glycerol > ethylene glycol > ethanol (figure 4b). Figure 4. (a) Cyclic voltammograms of Pd4S in (1) 0.1 M phosphate buffer solution (pH 7.0) and (2) in presence of 0.2 mM cytochrome c at a scan rate of 50 mVs-1 and (b) Voltammograms of Pd4S in presence of different alcohols (ethanol, EG and glycerol) in 1 M KOH solution at sweep rate of 50 mVs-1. Concentration of alcohols used is 0.1 M. The effect of dimensionality on the electro catalytic activity of nickel selenide phases forms part of the next chapter. Nickel selenide (NiSe) nanostructures possessing different morphologies of wires, spheres and hexagons are synthesized by varying the selenium precursors namely, selenourea, selenium dioxide (SeO2) and potassium selenocyanate (KSeCN), respectively using hydrothermal method. The different selenium precursors result in morphologies that are probably dictated by the by-products as well as relative rates of amorphous selenium formation and dissolution. The three different morphologies are used as catalysts for HER, ORR and glucose oxidation reactions. The wire morphology is found to be better than that of spheres and hexagons for all the reactions. Among the reactions studied, NiSe is found to be good for HER and glucose oxidation while ORR seems to terminate at the peroxide stage. In alkaline medium, nickel forms hydroxides and oxy-hydroxides and these oxyhydroxides are catalytically active towards the oxidation of glucose. Therefore, nickel selenides are employed as highly selective non-enzymatic glucose sensors and detection limit of 5 µM is observed. Electrical measurements on a single nanowire and a hexagon morphology of NiSe are carried out on devices fabricated by focused ion beam (FIB) technique (figure 5). The semiconducting nature of NiSe is revealed in the I-v measurements. The band gap of the material is found to be 1.9 eV and hence the single nanowire and hexagon are shown to act as visible light photodetector. Figure 5. SEM images of (a) single NiSe nanowire and (b) single NiSe hexagon with Pt contacts fabricated by FIB technique. Figure 6. Cyclic voltammograms of NiSe nanowires in 0.5 M aqueous NaOH in the (i) absence and (ii) the presence of 0.5 mM glucose, at a scan rate of 20 mVs-1 and (b) Galvanostatic discharge performance of Ni3Se2 with different morphologies (A, B and C represent Ni3Se2 prepared from SeO2, selenourea and KSeCN respectively). The next chapter includes the synthesis of different morphologies of Ni3Se2 using three different selenium precursors (SeO2, KSeCN and selenourea) and the study of their activities towards electrochemical reactions such as HER and glucose oxidation (figure 6a). Electrical measurements demonstrated the metallic behaviour of the material. These are also shown to be efficient electrode materials in energy storage devices such as supercapacitors with high specific capacitance of 2200 F/g (figure 6b). The studies are summarized in the last chapter with scope for further work. The appendixes show preliminary studies on electrooxidation of glycerol and propanol on Pd supported on TiN, synthesis of other selenides of Ni, Cu, Ag and Ti, and electro synthesis of metal-organic frameworks. (For figures pl refer the abstract pdf file)