While using iron castings behind temperature of 500 C namely at cyclic heat straining degradation of structure and breaching iron castings. For this purpose introduce cast iron with content of Si and Mo. Focusing on improvement of SiMo51 for increased high-temmperature corrosion-and fatigue life in exhaust-gas temperatures up to 800 C. Thesis set up chemical microheterogeneity, properties, high temperature corosion and microhardness

The thesis is focused on assessment of fatigue behaviour of austempered ductile iron with nodular graphite. Optimal period of transformation was determined based on the best combination of stress and strain characteristics established by tensile test. Cyclic response and low-cycle fatigue life were studied under both stress-control and longitudinal strain-control mode at room temperature. For both modes, shapes of cyclic hardening curves are dependent on stress amplitude. Cyclic deformation curves (CDC) were fitted by power regression function. Results were compared with CDC established by multiple step test in both modes with verification of the influence of cyclic creep (high stress levels, stress-control mode). Experimental data of S-N curves are in agreement with the Manson-Coffin and the Basquin law. Fatigue and cyclic parameters were compared. Fatigue life time in high-cycle fatigue region was determined. Experimental data were fitted by suitable regression functions. Regression parameters and fatigue limit were established by means of each regression function. Experimental data in low- and high-cycle fatigue regions were used to construct S-N curve and to determine relevant parameters. Discontinuity of experimental data was not observed. Low-cycle fatigue behaviour was predicted. Approximation of tolerance bands was realized in high-cycle and both high and low cycle fatigue regions.

The aim of this dissertation work is the evaluation of the influence of nickel alloying on the structure and mechanical properties, both monotonic and dynamic, of nodular cast iron with ferritic and bainitic matrix. Two chock melts with 0.5 and 2.7 % Ni were used to study the nickel influence. The quantitative evaluation of structure of these melts using image analysis was done and basic tensile mechanical properties were determined. Subsequently, the time optimization of two-stage ferritic annealing and isothermal austempered heat treatment at 375 °C was performed with the aim to obtain optimal ferritic and bainitic structures with best static and dynamic mechanical properties. After ferritic annealing the nickel alloying contributes to substitution hardening of ferritic matrix which positively affects its strength and other mechanical properties. The higher nickel content in the bainitic structure causes the shift of phase transformation times to longer times which results in restricted production of small carbides and in bigger volume of retained austenite. These features were confirmed by observation in transmission electron microscope. Precise tensile and low cycle fatigue tests at temperatures 23 and – 45 °C were performed on the optimized structures of both nodular cast irons. As a result of the notch effect of graphite nodules, microplastic deformation of both nodular cast irons was observed at stresses which were lower than the yield stress. The Hollomon's equation very well describes the individual parts of tensile curves for both nodular cast irons including their mutual comparison. From the low cycle fatigue tests, the cyclic hardening/softening curves, the evolution of elastic modulus and hysteresis loop shape parameters, cyclic stress-strain curves and fatigue life curves were obtained for both temperatures and materials. Moreover, the decrease of retained austenite volume was measured by neutron diffraction and the evolution of surface relief was characterized during cyclic straining for both austempered nodular cast irons at both temperatures. On the basis of these results both cyclic plasticity and fatigue degradation mechanisms in relation to the cyclic strain localization were described for both nodular cast irons.

The thesis is focused on assessment of fatigue behaviour of austempered ductile iron with nodular graphite. Optimal period of transformation was determined based on the best combination of stress and strain characteristics established by tensile test. Cyclic response and low-cycle fatigue life were studied under both stress-control and longitudinal strain-control mode at room temperature. For both modes, shapes of cyclic hardening curves are dependent on stress amplitude. Cyclic deformation curves (CDC) were fitted by power regression function. Results were compared with CDC established by multiple step test in both modes with verification of the influence of cyclic creep (high stress levels, stress-control mode). Experimental data of S-N curves are in agreement with the Manson-Coffin and the Basquin law. Fatigue and cyclic parameters were compared. Fatigue life time in high-cycle fatigue region was determined. Experimental data were fitted by suitable regression functions. Regression parameters and fatigue limit were established by means of each regression function. Experimental data in low- and high-cycle fatigue regions were used to construct S-N curve and to determine relevant parameters. Discontinuity of experimental data was not observed. Low-cycle fatigue behaviour was predicted. Approximation of tolerance bands was realized in high-cycle and both high and low cycle fatigue regions.

Internal Combustion Engine (ICE) exhaust components are exposed to extreme operating temperatures. Thus, it is necessary that they are designed with materials that can sustain thermal and vibrational stresses. This study investigates the wear mechanisms and tribological performance of the exhaust manifold joint in Scania CV diesel trucks, focusing on the lip seal ring between the exhaust and turbo manifolds. The joint is prone to wear due to thermal and vibrational stresses, impacting its service life and raising environmental concerns. The manifold material, ductile cast iron SiMo51, offers good thermal resistance, while the lip seal ring, made of Inconel 718c, provides excellent thermal fatigue and corrosion resistance, coated with AlTiN for wear and oxidation resistance. However, the tribological performance of this joint and material combination remains unknown, necessitating further research.  This work aims to understand wear initiation mechanisms and their relationship with temperature. Test setups were established using an oscillating cylinder on disc configuration in the SRV 3 tribometer. SiMo51 uncoated/coated with Tribaloy 400 and Inconel 718c uncoated/coated with AlTiN were tested against each other to identify the best material pair. Analysis involved coefficient of friction, visual inspection, wear volume measurements, SEM micrographs, and EDS for surface chemical composition. Results indicated that friction behaviour is temperature-dependent, with oxide layer formation reducing the coefficient of friction when the manifold is uncoated, while the opposite occurs when coated with Tribaloy 400. Wear behaviour varied based on material combinations and temperature. Uncoated manifold exhibited dominant adhesion (galling) accompanied by tribo-oxidation at higher temperatures, with maximum wear volumes at room temperature. Introduction of T-400 on the manifold initiated galling on the lip seal, leading to abrasion on the manifold surface, accompanied by tribo-oxidation at elevated temperatures. Wear increased until 500°C, followed by a decrease at 700°C. Further explanations of T-400 wear behaviour are lacking in the literature.