Spelling suggestions: "subject:"dupletos"" "subject:"duplessy""
1 |
Unapređenje kvaliteta alata za livenje pod pritiskom primenom tehnologija inženjerstva površina / Application of surface engineering technologies for improvement of diecasting tools qualityTerek Pal 21 September 2016 (has links)
<p>Proučavane su koroziona postojanost i tendencija lepljenja različitih<br />materijala u kontaktu sa tečnom Al–Si–Cu legurom. Ispitivanjem su<br />obuhvaćeni čelik za rad na toplo, plazma nitrirani čelik i dupleks<br />slojevi sa CrN, TiAlN, TiAlSiN i CrAlN prevlakama, različitog nivoa<br />površinske hrapavosti. Za ispitivanja pomenutih fenomena<br />primenjena je metoda izvlačenja, koja je unapređena kako bi se povećale<br />njena tačnost i verodostojnost simulacije procesa livenja. Korozioni<br />efekti su pojačani tako što su uzorci osim kratkog kontakta sa odlivkom<br />zadržavani i u dužim periodima u kontaktu sa tečnom legurom (5 i 20<br />min). Uprkos opštim stavovima, za ispitivane materijale je<br />ustanovljeno da su sile izvlačenja uzoraka iz Al–Si–Cu odlivaka<br />nezavisne od njihovog hemijskog sastava. Uticaj hrapavosti je izražen<br />kod uzoraka sa prevlakama kod kojih pri smanjenju hrapavosti dolazi do<br />povećanja sile izvlačenja. Sve ispitane prevlake su sklone mehaničkom<br />lepljenju Al–Si–Cu legure za svoje površine, ali sa aspekta korozije u<br />tečnom metalu značajno prevazilaze performanse čelika i plazma<br />nitriranog sloja. Duži kontakt livene legure sa površinama prevlaka<br />uzrokovao je niže vrednosti sila izvlačenja, što je posledica<br />oksidacije površina prevlaka. Ustanovljeno je da su ispitivane<br />prevlake inertne ka tečnoj leguri aluminijuma. Međutim, dolazi do<br />oksidacije i korozije materijala podloge kroz greške rasta koje su<br />prisutne u prevlakama. Stečena znanja o identifikovanim<br />mehanizmima habanja i propadanja zaštitnih slojeva prevlaka<br />poslužiće daljem razvoju dupleks slojeva namenjenih za zaštitu alata<br />za livenje pod pritiskom.</p> / <p>Corrosion resistance and soldering tendency of different materials in molten<br />Al–Si–Cu alloy were studied. Hot-working tool steel, plasma nitrided steel and<br />duplex layers with CrN, TiAlN, TiAlSiN and CrAlN top coatings, which were<br />produced to various degree of surface roughness, were covered by the study.<br />An ejection test was employed for investigation of the concerned phenomena.<br />The ejection test was improved in order to increase its accuracy and the<br />reliability of process simulation. Samples were examined in both short and<br />extended periods of contact (5 and 20 min) with liquid casting. Casting<br />solidification was extended in order to intensify the corrosion effects. Contrary<br />to common findings, it was found that the ejection force of the investigated<br />materials does not depend on their chemical composition. For the coated<br />samples, a pronounced dependence of the ejection force on the surface<br />roughness was found. The ejection force increases with decrease in surface<br />roughness. All investigated coatings are prone to mechanical soldering by Al–<br />Si–Cu alloy. Still, their corrosion resistance substantially exceeds the corrosion<br />resistance of steel and plasma nitrided layer. Longer exposure of coated<br />samples to cast alloy induced lower ejection forces, which is a consequence<br />of coatings oxidation. It was found that the investigated coatings are inert to<br />liquid aluminium. However, the underlying material undergoes oxidation and<br />corrosion through coating growth defects. The findings concerning the wear<br />mechanisms of protective layers support further development of duplex layers<br />intended for die casting tools protection.</p>
|
Page generated in 0.0181 seconds