Solid oxide fuel cells (SOFCs) are electrochemical energy conversion devices that directly transform the chemical energy of fuel into electrical energy. They generate electricity far more efficiently and with fewer emissions per megawatt-hour compared to any combustion-based power generation system. More remarkably, SOFCs can directly use hydrocarbon fuels without requiring external fuel reforming, employing low-cost Ni catalyst instead of noble-metal catalysts used for low-temperature fuel cells. However, the conventional SOFCs using Ni-based anodes fed with carbon-containing fuels have one pitfall; the carbon produced by hydrocarbon cracking is deposited on the Ni surface, thereby precluding the surface of the Ni-based anodes from being available for further fuel oxidation and consequently impeding SOFC operation. This dissertation focuses on overcoming this critical drawback to allow for the simultaneous use of Ni-based anodes and hydrocarbon fuels. Further work focuses on improving SOFC performance to provide the highest efficiencies possible. To boost the power densities of SOFCs, a novel, facile approach to modify the surface structure of anode powders and thereby enlarge the three-phase boundary (TPB) regions of anodes is presented. One such powder preparation method based on the electric charge variation of oxides depending upon the pH of the solution results in significantly extended TPB regions and thus a remarkable increase in power densities of SOFCs. Another method involves the formation of Ce₁₋[subscript x]Gd₁₋[subscript y]Ni[subscript x+y]VO₄₋[subscript delta] at the phase boundaries between NiO and Ce₀.₈Gd₀.₂O₁.₉ (GDC) by V⁵⁺-incorporation onto NiO surface; this method improves the microstructure of Ni-GDC-based anodes and considerably lowers GDC electrolyte sintering temperature, thereby enhancing the SOFC performance. With these high performance anodes, natural gas-fueled SOFCs are studied through two strategies to alleviate coking: incorporation of catalytic materials onto the Ni surface and the introduction of catalytic functional layers (CFLs) to the outer surface of an anode-supported single cell. Hydrogen tungsten bronze and hydroxylated Sn formed on the Ni surface provide hydroxyls for the deposited solid carbon, removing it from the anodes as CO₂. Moreover, the use of hydrophilic Sn or Sb-incorporated Ni-GDC CFLs prevents the anode from being exposed directly to hydrocarbon fuels and controls the solid carbon accumulation similarly to the former strategy. / text

<p dir="ltr">Lithium-ion (Li-ion) batteries are promising electrochemical energy storage and conversion systems to drive the rechargeable world toward a sustainable future. Following the breakthrough of material innovations, advanced Li-ion batteries have significantly mitigated the range and lifetime anxieties of electric vehicles (EVs) and consumer electronics. Nevertheless, state-of-the-art Li-ion chemistries still suffer from several defects, such as rapid degradations under abusive or fast-charge scenarios and unfavorable high thermal instabilities. Essentially, aging mechanisms and safety hazards of Li-ion cells are strongly coupled events. The cell safety factors are most likely to be deteriorated as degradation progresses, making the cell less safe after a long-term deployment. In this thesis, we comprehensively investigate thermo-electrochemical interactions on the safety of Li-ion batteries. Fundamental principles of Li-ion batteries, basic knowledge about material-level thermal instabilities at electrode-electrolyte interphases, thermal characterization approaches, and thermal runaway mechanisms under abusive scenarios are fully overviewed. Thermally unstable characteristics of key cell components, including inter-electrode crosstalk as a result of oxygen liberation from cathode lattice structures, significant electric energy release from massive internal short circuit due to separator collapse, anode-centric lithium-plating-induced early exotherm, and silicon-dopant-driven thermal risks of composite anodes, are specifically discussed to understand their critical role in accelerating cell-level thermal runaway catastrophes. Aging pathways of Li-ion cells under off-normal conditions, particularly overdischarge and fast charging, are thoroughly elucidated using a promising reference electrode architecture, which effectively deconvolutes the electrode behaviors from the complex full-cell performance for precise identification of the root causes in cell failure. Given the profound revelation of degradation-safety sophistication in various Li-ion chemistries, corresponding mitigation and prevention strategies are proposed to maximize cell lifetime and reliability. This thesis provides new insights into aging and safety diagnostics of cutting-edge Li-ion batteries, taking one step further in the online monitoring of battery state of health to develop adaptive battery management systems.</p>

A Comprehensive review of literature on electrode materials for lithium-ion batteries is provided in Chapter 1 of the thesis. Chapter 2 deals with the studies on porous, sub-micrometer size LiNi1/3Co1/3O2 as a positive electrode material for Li-ion cells synthesized by inverse microemulsion route and polymer template route. The electromechanical characterization studies show that carbon-coated LiNi1/3Co1/3O2 samples exhibit improved rate capability and cycling performance. Furthermore, it is anticipated that porous LiNi1/3Co1/3O2 could be useful for high rates of charge-discharge cycling. Synthesis of sub-micrometer size, porous particles of LiNi1/3Co1/3O2 using a tri-block copolymer as a soft template is carried out. LiNi1/3Co1/3O2 sample prepared at 900ºC exhibits a high rate capability and stable capacity retention of cycling. The electrochemical performance of LiNi1/3Co1/3O2 prepared in the absence of the polymer template is inferior to that of the sample prepared in the presence of the polymer template. Chapter 4 involves the synthesis of sub-micrometer size particles of LiMn2O4 in quaternary microemulsion medium. The electrochemical characterization studies provide discharge capacity values of about 100 mAh g-1 at C/5 rate and there is moderate decrease in capacity by increasing the rate of charge-discharge cycling. Studies also include charge-discharge cycling as well as ac impedance studies in temperature range from -10 to 40º C. Chapter 5 reports the synthesis of nano-plate LiFePO4 by polyol route starting from two reactants, namely, FePO42H2O and LiOH.2H2O. The electrodes fabricated out of nano-plate of LiFePO4 exhibit a high electrochemical activity. A stable capacity of about 155 mAh g-1 is measured at 0.2 C over 50 charge-discharge cycles. Mesoporous LiFePO4/C composite with two sizes of pores is prepared for the first time via solution-based polymer template technique. The precursor of LiFePO4/C composite is heated at different temperatures in the range from 600 to 800ºC to study the effect of crystalllinity, porosity and morphology on the electrochemical performance. The compound obtained at 700ºC exhibits a high rate capability and stable capacity retention on cycling with pore size distribution around 4 and 46nm. In Chapter 6, the electrochemical characterization of LiMn2O4 in an aqueous solution of 5 M LiNO3 is reported. A typical cell employing LiMn2O4 as the positive electrode and V2O5 as the negative electrode was assembled and the characterized by charge-discharge cycling in 5 M LiNO3 aqueous electrolyte. Furthermore, it is shown that Li+-ion in LiMn2O4 can be replaced by other divalent ions resulting in the formation of MMn2O4 (M = Ca, Mg, Ba and Sr) in aqueous M(NO3)2 electrolytes by subjecting LiMn2O4 electrodes to cyclic voltametry. Cyclic voltammetry and chronopotentiometry studies suggest that MMn2O4 can undergo reversible redox reaction by intercalation/deintercalation of M2+-ions in aqueous M(NO3)2 electrolytes.

Submitted by Marco Antonio Oliveira da Silva (maosilva@ipen.br) on 2016-12-21T17:42:04Z No. of bitstreams: 0 / Made available in DSpace on 2016-12-21T17:42:04Z (GMT). No. of bitstreams: 0 / Os catalisadores eletroquímicos binários de PtSn/C, PdSn/C e PtPd/C foram sintetizados em diferentes proporções pelo método da redução via borohidreto, posteriormente estes foram caracterizados por microscopia eletrônica de transmissão, difração de raios X, espectroscopia no infravermelho por transformada de Fourier (PtSn/C e PdSn/C) e energia dispersiva de raios X. As atividades eletroquímicas dos diferentes materiais preparados foram avaliadas por intermédio de voltametria cíclica, cronoamperometria e curvas de polarização em célula a combustível alimentada diretamente por etileno glicol em eletrólito alcalino. As curvas de densidade de potência indicaram que os catalisadores eletroquímicos contendo Sn e Pd são mais ativos para a reação de oxidação do etileno glicol, especialmente a composição 70%:30% - relação molar entre os metais suportados em carbono - dos catalisadores PtSn/C, PdSn/C e PtPd/C todos superando as medidas de potência do Pt/C. Este resultado indica que a adição de Sn e Pd favorece a oxidação do etileno glicol em meio alcalino. O melhor desempenho observado para os catalisadores eletroquímicos PtSn/C, PdSn/C e PtPd/C (70%:30%) poderia estar associado à sua maior seletividade quanto a formação de oxalato, ou seja , a formação deste produto resulta em um maior número de elétrons, por consequência em maiores valores de corrente. / Tese (Doutorado em Tecnologia Nuclear) / IPEN/T / Instituto de Pesquisas Energéticas e Nucleares - IPEN-CNEN/SP

A highly effective electrocatalyst is the central component of advanced electrochemical energy conversion. Recently, two-dimensional conjugated metal-organic frameworks (2D c-MOFs) have emerged as a class of promising electrocatalysts due to their advantages including 2D layered structure with high in-plane conjugation, intrinsic electrical conductivity, permanent pores, large surface area, chemical stability, and structural diversity. In this review, we summarize the recent advances of 2D c-MOF electrocatalysts for electrochemical energy conversion. Firstly, we introduce the chemical design principles and synthetic strategies of the reported 2D c-MOFs, as well as the functional design for the electrocatalysis. Subsequently, we present the representative 2D c-MOF electrocatalysts in various electrochemical reactions, such as hydrogen/oxygen evolution, and reduction reactions of oxygen, carbon dioxide and nitrogen. We highlight the strategies for the structural design and property tuning of 2D c-MOF electrocatalysts to boost the catalytic performance, and offer our perspectives in regard to the challenges to be overcome.