2,5-Di(thiophen-2-yl)-1-p-tolyl-1H-pyrrole (DTTP) was synthesized via reaction of 1,4-di(2-thienyl)-1,4-butanedione with p-toluidine in the presence of catalytical amount of p-toluenesulfonic acid (PTSA). Homopolymer P(DTTP) was achieved both by chemical and electrochemical techniques. Chemical polymerization of the monomer yielded a soluble polymer. The average molecular weight was determined by gel permeation chromatography (GPC) as Mn: 2.5x103 g/mol. The monomer was electrochemically polymerized in the presence of LiClO4, NaClO4 (1:1) as the supporting electrolyte in acetonitrile. Copolymer of DTTP in the presence of EDOT was synthesized via potentiodynamic method in ACN/ NaClO4/LiClO4 (0.1 M) solvent-electrolyte couple. Structural characterizations of samples were carried out via 1H, 13C Nuclear Magnetic Resonance (NMR) and Fourier Transform Infrared Spectroscopy (FTIR). Electrochemical behaviors of monomer and polymers were determined by Cyclic Voltammetry (CV). The morphologies of the polymer films were examined by Scanning Electron Microscopy (SEM). Conductivities of the films were measured by four probe technique. Electrochromic and spectroelectrochemical behavior of the polymers coated on ITO glass electrode were investigated, and their ability of employment in device construction was examined. Spectroelectrochemistry analysis of P(DTTP) revealed an electronic transition at 428 nm corresponding to &amp / #1087 / &amp / #8211 / &amp / #1087 / * transition with a band gap of 2.1 eV whereas P(DTTP-co-EDOT) revealed an electronic transition at 448 nm corresponding to &amp / #1087 / - &amp / #1087 / * transition with a band gap of 1.8 eV. Electrochromic investigations showed that P(DTTP) switches between greenish yellow and blue while P(DTTP-co-EDOT) was found to be multichromic, switching between red, yellow and blue. Switching time of the polymers was evaluated by a kinetic study upon measuring the percent transmittance (%T) at the maximum contrast point. Dual type polymer electrochromic devices (ECDs) based on P(DTTP) and P(DTTP-co-EDOT) with poly(3,4-ethylenedioxythiophene) (PEDOT) were constructed. Spectroelectrochemistry, electrochromic switching and open circuit stability of the devices were studied. They were found to have good switching times, reasonable contrasts and optical memories.

In this study, glucose oxidase and polyphenol oxidase were immobilized in conducting copolymer poly(N-(4-(3-thienyl methylene)-oxycarbonylphenyl)maleimide)-co-pyrrole(P(MBThi-co-Py)). A copolymer was electrochemically synthesized by using sodium dodecyl sulfate (SDS) as supporting electrolyte and characterized by FTIR, scanning electron microscopy (SEM) and conductivity measurements. Immobilization of glucose oxidase (GOD) and polyphenol oxidase (PPO) enzymes were performed in conducting PPy and P(MBThi-co-Py) matrices by electropolymerization. Kinetic parameters, maximum reaction rate (Vmax) and Michaelis-Menten constant (Km) were determined for the enzyme electrodes by help of Lineweaver-Burk plot. Effect of temperature and pH on GOD and PPO activity was examined. Operational stability and long term stability of the enzyme electrodes were investigated. The immobilized GOD and PPO electrodes were used for determination of glucose amount in Turkish orange juices and analyzing the concentration of phenolic compounds in Turkish red wines respectively.

Electrochemical polymerization of pyrrole functionalized polystyrene (PStPy) with pyrrole was carried out in water-sodium dodecyl sulfate solvent-electrolyte couple. Characterization of the resulting copolymer was performed via Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and four probe conductivity measurements. Glucose oxidase and polyphenol oxidase enzymes were immobilized in polypyrrole (PPy) and conducting copolymer of pyrrole functionalized polystyrene with pyrrole (P(PStPy-co-Py). Resulting enzyme electrodes were characterized by kinetic parameters / Vmax and Km. Behavior of enzyme electrodes upon temperature and pH changes were investigated. Glucose oxidase electrode was used for the determination of glucose in orange juice and polyphenol oxidase electrode was used for the determination of polyphenolic compounds in red wine.

New compounds consisting of 3-thienyl and aniline units linked by polyether bridges have been synthesized and their electrochemical polymerization was performed via constant potential electrolysis and cyclic voltammetry. In the case of 3-thienyl derivatives two compounds, 1,12-di-3-thienyl-2,5,8,11-tetraoxadodecane (MI) and 1,15-di-3-thienyl-2,5,8,11,14-pentaoxapentadecane (MII) were synthesized utilizing literature methods and their corresponding polymers, poly(I) and poly(II) were prepared in an electrolytic solution containing 0.1 M terabutylammonium hexafluorophosphate (TBAPF6) dissolved in CH3CN. On the other hand, polymerization of aniline derivatives, 2,2&#039 / -[ethane-1,2-diylbis(oxyethane-2,1-diyloxy)]dianiline (MIII) and 2,2&#039 / -[oxybis(ethane-2,1-diyloxyethane-2,1-diyloxy)]dianiline (MIV), was achieved in an aqueous solution containing 3.0 mol.L-1 H2SO4. Spectroelectrochemical (SPEL) properties and thermal analysis of the resulting polymers have been investigated using UV-vis, and Thermogravimetric Analysis (TGA). MIII was also polymerized via chemical oxidation for comparison purposes. The polymers were characterized using 1H-NMR and FT-IR spectroscopic techniques. Furthermore, copolymers of MIII and MIV with aniline (ANI) were also studied with cyclic voltammetry (CV). SPEL behavior and electrical conduction mechanism of resulting copolymers were investigated using UV-vis spectroscopic technique and four-point probe technique, respectively.

A new neutral state green polymer, poly (2,3-bis(4-tert-butylphenyl)-5,8-di(1H-pyrrol-2-yl) quinoxaline) (PTBPPQ) was synthesized and its copolymer with bis(3,4-ethylenedioxythiophene) (BiEDOT) and 4,7-bis(2,3-dihydrothieno[3,4-b][1,4]dioxin-5-yl)-2-dodecyl-2H-benzo [1,2,3] triazole (BEBT) were produced. Finally polymers&rsquo / potential use as an electrochromic material was investigated. Electrochromic properties of the polymers were investigated by several methods including spectroelectrochemistry, kinetic and colorimetry studies. Key properties of conjugated polymers such as band gap, maximum absorption wavelength, the intergap states that appear upon doping and evolution of polaron and bipolaron bands were investigated via spectroelectrochemistry experiments. Switching times and optical contrasts of the homopolymer and the copolymer were evaluated via kinetic studies. Copolymer of TBPPQ with BiEDOT and BEBT were electrochemically synthesized and characterized. Resulting copolymer films have distinct electrochromic properties and revealed multichromism through the entire visible region. Although BiEDOT and BEBT have different oxidation potentials, the resulting copolymers have very similar redox behaviors. In a monomer free solution, both copolymers show four colors from purple, gray, light green to transmissive blue with the variation of the applied potential. Copolymerization with BiEDOT and BEBT not only decreases the band gap, Eg, but also enhances the electrochromic and optical properties. Hence, electrochemical copolymerization is considered to be a powerful tool to improve the electrochromic properties of quinoxaline derivatives. It should be noted that PTBPPQ is one of the few examples of neutral state green polymeric materials with superior switching properties. Hence, PTBPPQ can be used as a green polymeric material for display technologies.

ABSTRACT ELECTROCHEMICAL SYNTHESIS OF CROWNED CONDUCTING POLYMERS: NATURE OF RADICAL CATIONS IN POLYMERIZATION AND MECHANISM OF CONDUCTIVITY Cihaner, Atilla Ph. D., Department of Chemistry Supervisor: Prof. Dr. Ahmet M. &Ouml / nal June 2004, 96 Pages Poly(dibenzo-18-crown-6) (Poly(DB18C6)) was synthesized by electrochemical oxidation of dibenzo-18-crown-6 (DB18C6) using a mixture of acetonitrile and dichloromethane as solvent and tetrabutylammonium tetrafluoroborate (TBABF4) or tetrabutylammonium hexafluorophosphate (TBAPF6) as supporting electrolyte. The anodic polymerization of DB18C6 was investigated using in-situ ESR and in-situ UV-VIS spectroscopic techniques. Spectroelectrochemical (SPEL) properties and thermal analysis of the resulting polymers have been investigated using UV-VIS, Differential Scanning Calorimetry (DSC), and Thermogravimetric Analysis (TGA). Furthermore, new compounds consisting of bis(2-thienyl) methyl (I and II) and bis(2-thienyl) ethyl (III) units linked by polyether bridges have been synthesized and their electrochemical polymerization was performed via constant potential electrolysis (CPE) in an electrolytic solution containing 0.1 M TBAPF6 dissolved in CH3CN. Also, I and II were polymerized via chemical oxidation which yielded broken &amp / #61552 / -conjugated polymers except for III. The polymers were characterized using 1H-NMR and FT-IR spectroscopic techniques. In addition, copolymers of III with thiophene (Th) and pyrrole (Py) were studied with cyclic voltammetry (CV). SPEL behaviors of the products were investigated using UV-VIS spectroscopic technique.

ABSTRACT IMMOBILIZATION OF INVERTASE, POLYPHENOL OXIDASE AND GLUCOSE OXIDASE IN CONDUCTING COPOLYMERS OF THIOPHENE-CAPPED POLYTETRAHYDROFURAN AND PYRROLE B&ouml / y&uuml / kbayram, AySe Elif Ph.D., Department of Chemistry Supervisor: Prof. Dr. Levent Toppare January 2005, 123 pages Immobilization of invertase, polyphenol oxidase (PPO) and glucose oxidase (GOD) enzymes were performed in electrochemically synthesized two types of conducting copolymers. One end and two end thiophene-capped polytetrahydrofuran (TPTHF-1 and TPTHF-2) were copolymerized with pyrrole under conditions of constant potential electrolysis. The copolymers were characterized by thermal, spectroscopic and scanning electron microscopy analyses. Immobilization was carried out via entrapment of enzymes in two types of matrices during the copolymerization of pyrrole with the insulating polymers in the presence of sodium dodecyl sulphate (SDS). Kinetic parameters: Maximum reaction rate (Vmax) and Michaelis-Menten constant (Km) were determined for the enzyme electrodes. Temperature optimization, pH optimization, operational stability and shelf-life of the enzyme electrodes were investigated. Enzyme electrodes of polyphenol oxidase and glucose oxidase were used to determine the amount of their substrates in samples. Polyphenol oxidase converts mono and diphenols to quinone. Amount of phenolic compounds in two kinds of wines were determined by analyzing the quinone amount. Glucose oxidase converts &amp / #61538 / -D-glucose to D-glucono-1,5-lactone. Glucose amount was determined in two kind of factory-produced orange juices by analyzing D-glucono-1,5-lactone.

A new class of &pi / -conjugated monomers was synthesized with combination of electron donating and electron-withdrawing heterocyclics to understand the effects of structural differences on electrochemical and optoelectronic properties of the resulting polymers. Electron deficient benzotriazole, substititued with benzyl from two available sites, coupled with stannylated electron donating groups, ethylenedioxythiophene (EDOT) and thiophene (Th), to yield four different monomers / 1-benzyl-4,7-di(thiophen-2-yl))-2H-benzo[d][1,2,3] triazole (BBTA), 2-benzyl-4,7-di(thiophen-2-yl))-2H-benzo[d][1,2,3] triazole (BBTS), 1-benzyl-4,7-bis(2,3-dihydrothieno[3,4-b]dioxin-5-yl)-2H-benzo [d][1,2,3]triazole (BBTEA), 2-benzyl-4,7-bis(2,3-dihydrothieno[3,4-b]dioxin-5-yl)-2H-benzo [d][1,2,3]triazole (BBTES). Furthermore, EDOT and thiophene terminated napthalene-2,3-crown ether containing monomers, 14,19-di(thiophen-2-yl)-naphtho[2,3-b][1,4,7,10,13] pentaoxacyclo pentadecane (TNCT), 14,19-bis(2,3-dihydrothieno[3,4-b][1,4]dioxin-5-yl)-naphtho[2,3-b][1,4,7,10,13]pentaoxacyclopenta decane (ENCE), were synthesized to observe the effect crown ether moiety on the final electrochemical and optoelectronic properties of resultant polymers. Cyclic voltammetry, UV-Vis-NIR spectroscopy and colorimetry techniques were employed to examine electrochemical and optoelectronic properties of all monomers and polymers. Experimental results showed that alteration of substituent, substitution position and donor groups&rsquo / strength lead to obtain polymers with different redox behaviors, optical band gaps and different number of achievable colored states.

En raison des problèmes d'instabilité à moyen termes des cellules solaires à colorant (DSSC), l'électrolyte liquide à base d'iodure a été remplacé par plusieurs types de matériaux solides transport de trous (HTM) pour obtenir des DSSCs à l'état solide (s-DSSCs). Parmi ces matériaux, l’utilisation des polymères conducteurs(PC) a attiré une attention considérable en raison de leur bonne stabilité, de leur haute conductivité et de la facilité de leur dépôt sur le semi-conducteur mésoporeux TiO2. Dans ce travail de thèse, plusieurs s-DSSCs basées sur des PC utilisés comme HTM ont été développés dans le but d'améliorer leurs performances photovoltaïques en tenant compte des deux objectifs suivants: (i) l'optimisation des processus de transfert inter facial de charge dans la cellule solaire, et (ii) l'optimisation du transport de charge dans le semi-conducteur d'oxyde de type n. Pour atteindre ces objectifs, chaque composant de la s-DSSC a été modifié afin d'étudier son effet sur les performances du dispositif final. En première tentative, une étude analytique est réalisée en faisant varier le sensibilisateur afin de déterminer les fragments de la structure du colorant, qui ont un effet important sur le processus de photopolymérization électrochimique in-situ (PEP) à la fois en milieu organique et en milieu aqueux mais aussi sur les performances des s-DSSCs. Sur la base de ces résultats, un nouveau concept a été développé et consiste en la suppression totale de l'interface entre le colorant et le HTM. Ceci est obtenu par la synthèse de nouveaux colorants liés de façon covalente à un monomère électroactif qui est co-polymérisé par la PEP in-situ. Le copolymère résultant, utilisé comme HTM, est lié de manière covalente au colorant. En outre, la nature de la liaison chimique, reliant le résidu triphénylamine TPA au monomère, est également étudiée comme un facteur clé dans les performances de s-DSSC. En outre, et pour optimiser les processus de transport de charges dans ce type de s-DSSC, de nouvelles s-DSSC basées sur ZnO ont été réalisées et étudiées. / Due to instability problems of dye sensitized solar cells (DSSCs) in longtime uses, the iodine based liquidelectrolyte has been replaced by several types of solid hole transporting materials (HTM) to perform solidstate DSSCs (s-DSSCs). Among them, the substitution by conducting polymers (CP) has attractedconsiderable attention because of their good stability, high hole-conductivity and simple deposition withinthe mesoporous TiO2 semiconductor. In this thesis work, several s-DSSCs based on CPs used as HTM havebeen developed in order to improve their photovoltaic performances taking into account the following twoobjectives: (i) the optimization of the interfacial charge transfer processes within the solar cell, and (ii) theoptimization of the charge transport within the n-type oxide semiconductor. To reach these goals, eachcomponent that constitutes the device was varied in order to investigate its effect on the device’sperformances. As first attempt, an analytical study is carried out by varying the sensitizer in order todetermine the fragments of the dyes structures, that have an important effect on the in-situ photoelectrochemical polymerization process (PEP) both in organic and in aqueous media and hence on theperformances of the s-DSSCs. Based on these results, a new concept of removing completely the interfacebetween the dye and the HTM is developed. This is achieved by the synthesis of new dyes covalently linkedto an electroactive monomer which is co-polymerized by in-situ PEP. The resulting co-polymer, used asHTM, is covalently linked to the dye. In addition, the nature of the chemical bond linking the triphenylamineresidue TPA to the monomer is also investigated as a key factor in the s-DSSCs performances. Besides, andto optimize the charge transport processes within this type of s-DSSC, the elaboration of novel ZnO baseds-DSSCs has been achieved and investigated.

L’objectif de ce travail étaient le développement de catalyseurs hétérogènes efficaces pour promouvoir des réactions asymétriques, en utilisant la polymérisation oxydante ou la formation de polymères de coordination. De nouveaux complexes de salen Co(III) chiraux modifiés par des groupements aromatiques sur les position 5, 5’ ont été préparés et testés dans le dédoublement cinétique hydrolytique (HKR) des époxydes terminaux en conditions homogènes. Ces complexes ont été ensuite engagés dans les polymérisations oxydantes électrochimiques ou chimiques, et une stratégie de copolymérisation a fourni des polymères chiraux très efficaces et stables pour catalyser l’HKR dans des conditions hétérogènes. Nous avons alors cherché à préparer un catalyseur capable de catalyser deux réactions en cascade, en copolymérisant deux complexes de salen portant des métaux différents. Pendant ces études, les complexes de salen Mn ont révélé leur participation active à la réaction d’HKR des époxydes terminaux catalysée par les complexes de salen Co(III), en augmentant l’excès énantiomérique du produit de façon significative. Les études mécanistiques ont été ensuite réalisées pour tenter de comprendre le rôle des complexes de Mn dans cette réaction. De plus, des complexes de salen fonctionnalisés par le groupement pyridine ou le groupement de type acide isophtalique ont été synthétisés. Ces complexes ont été utilisés pour préparer de nouveaux réseaux de polymères de coordination poreux chiraux (collaboration avec l’équipe LCI de l’ICMMO et l’Institut Lavoisier à Versailles), qui sont ensuite testés comme catalyseurs hétérogènes dans la réaction de Henry asymétrique et la réaction d’HKR. / The aim of this work was to prepare new chiral heterogeneous catalysts for asymmetric catalysis by oxidative polymerization of chiral organometallic complexes or by formation of chiral metal organic frameworks. New chiral salen Co(III) complexes modified by oxidizable aromatic groups at position 5,5’ have been prepared and tested as homogeneous catalysts in the Hydrolytic Kinetic Resolution (HKR) of terminal epoxides. These complexes have also been engaged into the oxidative electrochemical and chemical polymerization, and a copolymerization strategy has afforded very efficient and stable heterogeneous catalysts for the HKR. The idea of copolymerization has then been extended to the copolymerization of two salen complexes with different metals, which is expected to promote successively two different asymmetric transformations. During preliminary investigations, the salen Mn complexes have been found to be able to enhance the catalytic performance of salen Co(III) complexes in the HKR by increasing significantly the enantiomeric excess of the products. Mechanistic studies have thus been realized to understand the role of salen Mn complexes in this reaction. Besides, some chiral salen complexes functionalized by pyridine or isophtalic acid groups have been synthesized for the preparation of new chiral metal organic frameworks (collaboration with LCI of ICMMO and Institut Lavoisier of Versailles), which have also been tested in the asymmetric Henry reaction and the HKR as heterogeneous catalysts.