The experimental tests and analysis of a fuel cell unit and a 150 W fuel cell stack are performance in this research. The experimental items in this study are various the types of flow channels, fasten torque, inlet gas pressure, Pt loading density, oxidizers, electron collector type etc. Through above a series of the tests, we can understand the key factors which influence the performance of the PEMFC. The experimental results can also provide us references when one assemble a fuel cell stack in future. PEMFC can start quickly at low temperature and achieves stable output voltage. When the 8 N-M torque is applied to fasten the reaction chamber, the contact resistance between electrode and electron collector reaches a minimum value. By designing the flow channel properly, the membrane hydration can remain a good state so that the conductivity of the proton exchange membrane can not be hinder. We found that the optimum channel among three types of the test channels is the conventional channel with the rib width 2 mm. When the output power is largest. Our experiments display that the increase of Pt loading in cathode can improve PEMFC performance. At certain voltage, there is a critical value in Pt loading. PEMFC performance can not be improved when Pt loading increases over this value. When the inlet pressure in cathode side increase to 10~20 psi higher than the pressure in anode side, the output power can improve apparently. Keyword: Proton exchange membrane, Pt loading, electron collector.

The goal of this research is to test the design constraints of active dpp-bridged RuII,RhIII (dpp = 2,3-bis(2-pyridyl)pyrazine)) supramolecular photocatalysts for water reduction to H2 and provide mechanistic insights into the catalytic cycle. Two member of a new RuII,RhIII motifs with only one Rh-'Cl bond, [(bpy)2Ru(dpp)RhCl(tpy)](PF6)4 ( bpy = 2,2'-bipyridine, tpy = 2,2':6,2"-terpyridine) and [(bpy)2Ru(dpp)RhCl(tpm)](PF6)4, (tpm = tris(1-pyrazolyl)methane), and a cis-RhCl2 model system, [(bpy)2Ru(dpp)RhCl2(bpy)](PF6)3, were prepared. This new motif was to test whether two Rh-'Cl bonds on RhIII are required for the photocatalytic water reduction. 1H NMR spectroscopic analysis of complexes prepared using deuterated ligands was used to characterize these three RuII,RhIII supramolecular complexes. Electrochemical studies suggested that replacing bpy with a tridentate ligand on RhIII shifts the RhIII/II and RhII/I reduction couples positively, which can modulate the orbital energetics of the RhIII LUMO (lowest-unoccupied molecular orbital). This substitute also changes the rate of ligand dissociation following the reduction of RhIII. In tpm and bpy systems, RhII intermediate is more stable than that in the tpy system. All three complexes were good light absorbers in the visible region and weak emitters from their emissive Ru(dπ)-'dpp(π*) 3MLCT (metal-to-ligand charge transfer) excited states at room temperature. The population of a low-lying 3MMCT (metal-to-metal charge transfer) ES (excited state) from the 3MLCT ES contributed to the weak emission, indicating an important intramolecular electron transfer process from dpp' to RhIII upon photoexcitation. The lower-lying 3MMCT excited state in the tpm and tpy systems relative to the bpy system result in a higher rate constant (ket = 2.6 x 10^7 vs 1.7 x 10^7 s-1) for intramolecular electron transfer. Spectrophotochemical analysis suggested that all three complexes were photoinitiated electron collectors capable of collecting two electrons on the RhIII center to generate the RuII,RhI species in the presence of DMA (N,N-dimethylaniline). The observed H2 production from water using [(bpy)2Ru(dpp)RhCl(tpm)](PF6)4 and [(bpy)2Ru(dpp)RhCl(tpy)](PF6)4 established that two halides on RhIII are not necessary in the dpp-bridge RuII,RhIII supramolecular photocatalytic-water-reduction system. This new discovery opens a new approach to the design of different RuII,RhIII motifs for photocatalysis. The active species for water reduction is proposed to be [(bpy)2Ru(dpp)RhICl(TL)]3+ from [(bpy)2Ru(dpp)RhCl(TL)](PF6)4 (TL (terminal ligand) = tpy or tpm) and [(bpy)2Ru(dpp)Rh(bpy)]3+ from [(bpy)2Ru(dpp)RhCl2(bpy)](PF6)3 respectively. Included here is the design and study of a RuII,RhI complex, [(bpy)2Ru(dpp)RhCl(COD)](PF6)3 (COD =1,5-cyclooctadiene) to provide more insights into the photophysical and photochemical properties of polypyridyl RuII,RhI species. Electrochemical and photophysical studies revealed a dpp-based LUMO in this RuII,RhI complex, suggesting dpp reduction upon photoexcitation. Photochemical study found that [(bpy)2Ru(dpp)RhCl(COD)](PF6)3 is an active photocatalyst for water reduction and that additional reduction(s) is (are) required after the generation of the RuII,RhI active species in the RuII,RhIII supramolecular photocatalytic H2 production system. This hypothesis was supported by the electrocatalytic behaviors of the RuII,RhIII supramolecular complexes for proton reduction. Cyclic voltammetry results in the presence of an acid suggested that the protonolysis of the RuII,RhIIH and RuII,RhIH species are electrocatalytic H2-evolution pathways. The mechanism is acid-dependent and influenced by terminal ligand. The studies of electrocatalytic proton reduction on these RuII,RhIII complexes suggested several possible intermediates involved in the photocatalytic water reduction cycle. The insights gained from this research can provide guidance in designing new type of RuII,RhIII and RuII,RhI complexes with better photocatalytic and/or electrocatalytic H2 production performance. / Ph. D.