The site investigation phase plays a vital role in any foundation design where inadequate characterisation of the subsurface conditions may lead to either a significantly over designed foundation that is not cost-effective, or an under-designed foundation, which may result in foundation failure. As such, the scope of an investigation should be dependent on the conditions at the site and the importance of the structure. However, it is common for the expense dedicated to the site investigation to be a fraction of the total cost of the project, and is typically determined by budget and time constraints, and the experience and judgement of the geotechnical engineer. However, additional site investigation expenditure or sampling is expected to reduce the financial risk of the design by reducing the uncertainties in the geotechnical system and protecting against possible foundation failures. This research has quantified the relative benefits of undertaking site investigations of increased and differing scope. This has been achieved by simulating the design process to yield a foundation design based on the results of a site investigation. Such a design has been compared to an optimal design that utilises the complete knowledge of the soil, which has only been possible due to the use of simulated soils. Comparisons between these two design types indicate the performance of the site investigation to accurately or adequately characterise the site conditions. Furthermore, the design based on the results of the site investigation have been analysed using the complete knowledge of the soil. This yields a probability of failure and, therefore, has been included in a risk analysis where the costs associated with the site investigation have been measured against the financial risk of the design. As such, potential savings in financial risk for increased site investigation expenditure have been subsequently identified. A Monte Carlo analysis has been used in this research to incorporate the uncertainties in the foundation design process. Uncertainties have been included due to soil variability; sampling errors; measurement and transformation model errors; and errors related to the use of a simplified foundation response prediction method. The Monte Carlo analysis has also provided the means to obtain results in a probabilistic framework to enable reliability and risk analyses. Computer code has been specifically developed with an aim to: generate a simulated soil that conforms to the variability of soil properties; simulate a site investigation to estimate data for a foundation design; simulate the design of a foundation and conduct a reliability and risk analysis of such a design. Results indicate that there are significant benefits to be derived from increasing the scope of a site investigation in terms of the risk and reliability of the foundation design. However, it also appears that an optimal site investigation scope or expenditure exists where additional expenditure leads to a design with a higher financial risk due to the increased cost of the site investigation. The expected savings in terms of financial risk are significant when compared to the increased investigation cost. These results will assist geotechnical engineers in planning a site investigation in a more rational manner with knowledge of the associated risks. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1255275 / Thesis(Ph.D.) -- School of Civil and Environmental Engineering, 2006

The Patonga Claystone, a red bed facies in the Narrabeen Group of the Sydney Basin, is one of the most unfavorable rock units in the basin from a geotechnical point of view. This rock unit is composed of sandstone, siltstone, mudstone and claystone. One of the unfavorable characteristics is the low shear strength, which causes instability of cut slopes; another is its slaking-prone behaviour. Numerous measurements of geotechnical properties, along with extensive mineralogical and geochemical determinations, were carried out to identify cause of this slaking behaviour. Key techniques were the use of quantitative X-ray diffractometry for mineralogical analysis, and the determination of slake durability index and related properties to evaluate the slaking behaviour under both standard and more extended conditions. Standard (two cycle) slake durability test results indicate a range from low to high slake durability index values, with some mudstone samples having very low durability and some sandstones having very high slake durability indices. Jar slake test results indicate that the rock samples break rapidly and/or develop several fractures (Ij = 4) in an as-received state, but degrade to a pile of flakes or mud (Ij = 1) if the samples are oven dried before testing. The results for jar slake testing of oven-dried material are comparable, for individual samples, to those obtained from the more comprehensive slake durability tests. The mineralogy of the samples was evaluated by quantitative X-ray diffraction techniques using the Rietveld-based Siroquant processing system. Comparison to independent chemical data show a generally good level of agreement, suggesting that the mineralogical analysis results are consistent with the chemical composition of the individual rock samples. Good correlations were also obtained between clay mineralogy determined from orientedaggregate XRD analysis of the &lt2 micron fraction and the results from powder diffractometry and Siroquant analysis of the whole-rock samples. Evaluation of the slake durability characteristics and other geotechnical properties in relation to the quantitative mineralogy suggests that quartz and feldspar form a rigid framework in the rocks that resists the disruptive pressures that cause slaking. Expansion of the clay minerals by various processes, including the incorporation of water into the interlayer spaces of illite/smectite as well as changes in pore pressures associated with entry of water into micro-fractures in the clay matrix, are thought to produce the disruptions that cause slaking and degradation. An abundant clay matrix also reduces the strength of the rock materials, probably because of the less rigid nature of the clay minerals relative to the quartz and feldspar particles. As well as the mineralogy, the loss on ignition (LOI) and water absorption percentage were found to provide good indicators of longer-term slaking behaviour. Both properties are also related to the overall clay content. Rock samples with water absorption values of &lt10, 10-15 and &gt15% behave as highly durable, intermediate and less durable materials respectively. Rocks with LOI values of greater than 5% by weight behave as less durable rock materials, at least for the strata encompassed by the present study. The water absorption and LOI values were also used to develop a predictive model of slake durability characteristics for the different rock materials in the Patonga Claystone, providing a relatively simple basis for predicting longer-term stability in a range of geotechnical studies.

The Patonga Claystone, a red bed facies in the Narrabeen Group of the Sydney Basin, is one of the most unfavorable rock units in the basin from a geotechnical point of view. This rock unit is composed of sandstone, siltstone, mudstone and claystone. One of the unfavorable characteristics is the low shear strength, which causes instability of cut slopes; another is its slaking-prone behaviour. Numerous measurements of geotechnical properties, along with extensive mineralogical and geochemical determinations, were carried out to identify cause of this slaking behaviour. Key techniques were the use of quantitative X-ray diffractometry for mineralogical analysis, and the determination of slake durability index and related properties to evaluate the slaking behaviour under both standard and more extended conditions. Standard (two cycle) slake durability test results indicate a range from low to high slake durability index values, with some mudstone samples having very low durability and some sandstones having very high slake durability indices. Jar slake test results indicate that the rock samples break rapidly and/or develop several fractures (Ij = 4) in an as-received state, but degrade to a pile of flakes or mud (Ij = 1) if the samples are oven dried before testing. The results for jar slake testing of oven-dried material are comparable, for individual samples, to those obtained from the more comprehensive slake durability tests. The mineralogy of the samples was evaluated by quantitative X-ray diffraction techniques using the Rietveld-based Siroquant processing system. Comparison to independent chemical data show a generally good level of agreement, suggesting that the mineralogical analysis results are consistent with the chemical composition of the individual rock samples. Good correlations were also obtained between clay mineralogy determined from orientedaggregate XRD analysis of the &lt2 micron fraction and the results from powder diffractometry and Siroquant analysis of the whole-rock samples. Evaluation of the slake durability characteristics and other geotechnical properties in relation to the quantitative mineralogy suggests that quartz and feldspar form a rigid framework in the rocks that resists the disruptive pressures that cause slaking. Expansion of the clay minerals by various processes, including the incorporation of water into the interlayer spaces of illite/smectite as well as changes in pore pressures associated with entry of water into micro-fractures in the clay matrix, are thought to produce the disruptions that cause slaking and degradation. An abundant clay matrix also reduces the strength of the rock materials, probably because of the less rigid nature of the clay minerals relative to the quartz and feldspar particles. As well as the mineralogy, the loss on ignition (LOI) and water absorption percentage were found to provide good indicators of longer-term slaking behaviour. Both properties are also related to the overall clay content. Rock samples with water absorption values of &lt10, 10-15 and &gt15% behave as highly durable, intermediate and less durable materials respectively. Rocks with LOI values of greater than 5% by weight behave as less durable rock materials, at least for the strata encompassed by the present study. The water absorption and LOI values were also used to develop a predictive model of slake durability characteristics for the different rock materials in the Patonga Claystone, providing a relatively simple basis for predicting longer-term stability in a range of geotechnical studies.

The Patonga Claystone, a red bed facies in the Narrabeen Group of the Sydney Basin, is one of the most unfavorable rock units in the basin from a geotechnical point of view. This rock unit is composed of sandstone, siltstone, mudstone and claystone. One of the unfavorable characteristics is the low shear strength, which causes instability of cut slopes; another is its slaking-prone behaviour. Numerous measurements of geotechnical properties, along with extensive mineralogical and geochemical determinations, were carried out to identify cause of this slaking behaviour. Key techniques were the use of quantitative X-ray diffractometry for mineralogical analysis, and the determination of slake durability index and related properties to evaluate the slaking behaviour under both standard and more extended conditions. Standard (two cycle) slake durability test results indicate a range from low to high slake durability index values, with some mudstone samples having very low durability and some sandstones having very high slake durability indices. Jar slake test results indicate that the rock samples break rapidly and/or develop several fractures (Ij = 4) in an as-received state, but degrade to a pile of flakes or mud (Ij = 1) if the samples are oven dried before testing. The results for jar slake testing of oven-dried material are comparable, for individual samples, to those obtained from the more comprehensive slake durability tests. The mineralogy of the samples was evaluated by quantitative X-ray diffraction techniques using the Rietveld-based Siroquant processing system. Comparison to independent chemical data show a generally good level of agreement, suggesting that the mineralogical analysis results are consistent with the chemical composition of the individual rock samples. Good correlations were also obtained between clay mineralogy determined from orientedaggregate XRD analysis of the &lt2 micron fraction and the results from powder diffractometry and Siroquant analysis of the whole-rock samples. Evaluation of the slake durability characteristics and other geotechnical properties in relation to the quantitative mineralogy suggests that quartz and feldspar form a rigid framework in the rocks that resists the disruptive pressures that cause slaking. Expansion of the clay minerals by various processes, including the incorporation of water into the interlayer spaces of illite/smectite as well as changes in pore pressures associated with entry of water into micro-fractures in the clay matrix, are thought to produce the disruptions that cause slaking and degradation. An abundant clay matrix also reduces the strength of the rock materials, probably because of the less rigid nature of the clay minerals relative to the quartz and feldspar particles. As well as the mineralogy, the loss on ignition (LOI) and water absorption percentage were found to provide good indicators of longer-term slaking behaviour. Both properties are also related to the overall clay content. Rock samples with water absorption values of &lt10, 10-15 and &gt15% behave as highly durable, intermediate and less durable materials respectively. Rocks with LOI values of greater than 5% by weight behave as less durable rock materials, at least for the strata encompassed by the present study. The water absorption and LOI values were also used to develop a predictive model of slake durability characteristics for the different rock materials in the Patonga Claystone, providing a relatively simple basis for predicting longer-term stability in a range of geotechnical studies.

The Patonga Claystone, a red bed facies in the Narrabeen Group of the Sydney Basin, is one of the most unfavorable rock units in the basin from a geotechnical point of view. This rock unit is composed of sandstone, siltstone, mudstone and claystone. One of the unfavorable characteristics is the low shear strength, which causes instability of cut slopes; another is its slaking-prone behaviour. Numerous measurements of geotechnical properties, along with extensive mineralogical and geochemical determinations, were carried out to identify cause of this slaking behaviour. Key techniques were the use of quantitative X-ray diffractometry for mineralogical analysis, and the determination of slake durability index and related properties to evaluate the slaking behaviour under both standard and more extended conditions. Standard (two cycle) slake durability test results indicate a range from low to high slake durability index values, with some mudstone samples having very low durability and some sandstones having very high slake durability indices. Jar slake test results indicate that the rock samples break rapidly and/or develop several fractures (Ij = 4) in an as-received state, but degrade to a pile of flakes or mud (Ij = 1) if the samples are oven dried before testing. The results for jar slake testing of oven-dried material are comparable, for individual samples, to those obtained from the more comprehensive slake durability tests. The mineralogy of the samples was evaluated by quantitative X-ray diffraction techniques using the Rietveld-based Siroquant processing system. Comparison to independent chemical data show a generally good level of agreement, suggesting that the mineralogical analysis results are consistent with the chemical composition of the individual rock samples. Good correlations were also obtained between clay mineralogy determined from orientedaggregate XRD analysis of the &lt2 micron fraction and the results from powder diffractometry and Siroquant analysis of the whole-rock samples. Evaluation of the slake durability characteristics and other geotechnical properties in relation to the quantitative mineralogy suggests that quartz and feldspar form a rigid framework in the rocks that resists the disruptive pressures that cause slaking. Expansion of the clay minerals by various processes, including the incorporation of water into the interlayer spaces of illite/smectite as well as changes in pore pressures associated with entry of water into micro-fractures in the clay matrix, are thought to produce the disruptions that cause slaking and degradation. An abundant clay matrix also reduces the strength of the rock materials, probably because of the less rigid nature of the clay minerals relative to the quartz and feldspar particles. As well as the mineralogy, the loss on ignition (LOI) and water absorption percentage were found to provide good indicators of longer-term slaking behaviour. Both properties are also related to the overall clay content. Rock samples with water absorption values of &lt10, 10-15 and &gt15% behave as highly durable, intermediate and less durable materials respectively. Rocks with LOI values of greater than 5% by weight behave as less durable rock materials, at least for the strata encompassed by the present study. The water absorption and LOI values were also used to develop a predictive model of slake durability characteristics for the different rock materials in the Patonga Claystone, providing a relatively simple basis for predicting longer-term stability in a range of geotechnical studies.

The Patonga Claystone, a red bed facies in the Narrabeen Group of the Sydney Basin, is one of the most unfavorable rock units in the basin from a geotechnical point of view. This rock unit is composed of sandstone, siltstone, mudstone and claystone. One of the unfavorable characteristics is the low shear strength, which causes instability of cut slopes; another is its slaking-prone behaviour. Numerous measurements of geotechnical properties, along with extensive mineralogical and geochemical determinations, were carried out to identify cause of this slaking behaviour. Key techniques were the use of quantitative X-ray diffractometry for mineralogical analysis, and the determination of slake durability index and related properties to evaluate the slaking behaviour under both standard and more extended conditions. Standard (two cycle) slake durability test results indicate a range from low to high slake durability index values, with some mudstone samples having very low durability and some sandstones having very high slake durability indices. Jar slake test results indicate that the rock samples break rapidly and/or develop several fractures (Ij = 4) in an as-received state, but degrade to a pile of flakes or mud (Ij = 1) if the samples are oven dried before testing. The results for jar slake testing of oven-dried material are comparable, for individual samples, to those obtained from the more comprehensive slake durability tests. The mineralogy of the samples was evaluated by quantitative X-ray diffraction techniques using the Rietveld-based Siroquant processing system. Comparison to independent chemical data show a generally good level of agreement, suggesting that the mineralogical analysis results are consistent with the chemical composition of the individual rock samples. Good correlations were also obtained between clay mineralogy determined from orientedaggregate XRD analysis of the &lt2 micron fraction and the results from powder diffractometry and Siroquant analysis of the whole-rock samples. Evaluation of the slake durability characteristics and other geotechnical properties in relation to the quantitative mineralogy suggests that quartz and feldspar form a rigid framework in the rocks that resists the disruptive pressures that cause slaking. Expansion of the clay minerals by various processes, including the incorporation of water into the interlayer spaces of illite/smectite as well as changes in pore pressures associated with entry of water into micro-fractures in the clay matrix, are thought to produce the disruptions that cause slaking and degradation. An abundant clay matrix also reduces the strength of the rock materials, probably because of the less rigid nature of the clay minerals relative to the quartz and feldspar particles. As well as the mineralogy, the loss on ignition (LOI) and water absorption percentage were found to provide good indicators of longer-term slaking behaviour. Both properties are also related to the overall clay content. Rock samples with water absorption values of &lt10, 10-15 and &gt15% behave as highly durable, intermediate and less durable materials respectively. Rocks with LOI values of greater than 5% by weight behave as less durable rock materials, at least for the strata encompassed by the present study. The water absorption and LOI values were also used to develop a predictive model of slake durability characteristics for the different rock materials in the Patonga Claystone, providing a relatively simple basis for predicting longer-term stability in a range of geotechnical studies.

The Patonga Claystone, a red bed facies in the Narrabeen Group of the Sydney Basin, is one of the most unfavorable rock units in the basin from a geotechnical point of view. This rock unit is composed of sandstone, siltstone, mudstone and claystone. One of the unfavorable characteristics is the low shear strength, which causes instability of cut slopes; another is its slaking-prone behaviour. Numerous measurements of geotechnical properties, along with extensive mineralogical and geochemical determinations, were carried out to identify cause of this slaking behaviour. Key techniques were the use of quantitative X-ray diffractometry for mineralogical analysis, and the determination of slake durability index and related properties to evaluate the slaking behaviour under both standard and more extended conditions. Standard (two cycle) slake durability test results indicate a range from low to high slake durability index values, with some mudstone samples having very low durability and some sandstones having very high slake durability indices. Jar slake test results indicate that the rock samples break rapidly and/or develop several fractures (Ij = 4) in an as-received state, but degrade to a pile of flakes or mud (Ij = 1) if the samples are oven dried before testing. The results for jar slake testing of oven-dried material are comparable, for individual samples, to those obtained from the more comprehensive slake durability tests. The mineralogy of the samples was evaluated by quantitative X-ray diffraction techniques using the Rietveld-based Siroquant processing system. Comparison to independent chemical data show a generally good level of agreement, suggesting that the mineralogical analysis results are consistent with the chemical composition of the individual rock samples. Good correlations were also obtained between clay mineralogy determined from orientedaggregate XRD analysis of the &lt2 micron fraction and the results from powder diffractometry and Siroquant analysis of the whole-rock samples. Evaluation of the slake durability characteristics and other geotechnical properties in relation to the quantitative mineralogy suggests that quartz and feldspar form a rigid framework in the rocks that resists the disruptive pressures that cause slaking. Expansion of the clay minerals by various processes, including the incorporation of water into the interlayer spaces of illite/smectite as well as changes in pore pressures associated with entry of water into micro-fractures in the clay matrix, are thought to produce the disruptions that cause slaking and degradation. An abundant clay matrix also reduces the strength of the rock materials, probably because of the less rigid nature of the clay minerals relative to the quartz and feldspar particles. As well as the mineralogy, the loss on ignition (LOI) and water absorption percentage were found to provide good indicators of longer-term slaking behaviour. Both properties are also related to the overall clay content. Rock samples with water absorption values of &lt10, 10-15 and &gt15% behave as highly durable, intermediate and less durable materials respectively. Rocks with LOI values of greater than 5% by weight behave as less durable rock materials, at least for the strata encompassed by the present study. The water absorption and LOI values were also used to develop a predictive model of slake durability characteristics for the different rock materials in the Patonga Claystone, providing a relatively simple basis for predicting longer-term stability in a range of geotechnical studies.

The Patonga Claystone, a red bed facies in the Narrabeen Group of the Sydney Basin, is one of the most unfavorable rock units in the basin from a geotechnical point of view. This rock unit is composed of sandstone, siltstone, mudstone and claystone. One of the unfavorable characteristics is the low shear strength, which causes instability of cut slopes; another is its slaking-prone behaviour. Numerous measurements of geotechnical properties, along with extensive mineralogical and geochemical determinations, were carried out to identify cause of this slaking behaviour. Key techniques were the use of quantitative X-ray diffractometry for mineralogical analysis, and the determination of slake durability index and related properties to evaluate the slaking behaviour under both standard and more extended conditions. Standard (two cycle) slake durability test results indicate a range from low to high slake durability index values, with some mudstone samples having very low durability and some sandstones having very high slake durability indices. Jar slake test results indicate that the rock samples break rapidly and/or develop several fractures (Ij = 4) in an as-received state, but degrade to a pile of flakes or mud (Ij = 1) if the samples are oven dried before testing. The results for jar slake testing of oven-dried material are comparable, for individual samples, to those obtained from the more comprehensive slake durability tests. The mineralogy of the samples was evaluated by quantitative X-ray diffraction techniques using the Rietveld-based Siroquant processing system. Comparison to independent chemical data show a generally good level of agreement, suggesting that the mineralogical analysis results are consistent with the chemical composition of the individual rock samples. Good correlations were also obtained between clay mineralogy determined from orientedaggregate XRD analysis of the &lt2 micron fraction and the results from powder diffractometry and Siroquant analysis of the whole-rock samples. Evaluation of the slake durability characteristics and other geotechnical properties in relation to the quantitative mineralogy suggests that quartz and feldspar form a rigid framework in the rocks that resists the disruptive pressures that cause slaking. Expansion of the clay minerals by various processes, including the incorporation of water into the interlayer spaces of illite/smectite as well as changes in pore pressures associated with entry of water into micro-fractures in the clay matrix, are thought to produce the disruptions that cause slaking and degradation. An abundant clay matrix also reduces the strength of the rock materials, probably because of the less rigid nature of the clay minerals relative to the quartz and feldspar particles. As well as the mineralogy, the loss on ignition (LOI) and water absorption percentage were found to provide good indicators of longer-term slaking behaviour. Both properties are also related to the overall clay content. Rock samples with water absorption values of &lt10, 10-15 and &gt15% behave as highly durable, intermediate and less durable materials respectively. Rocks with LOI values of greater than 5% by weight behave as less durable rock materials, at least for the strata encompassed by the present study. The water absorption and LOI values were also used to develop a predictive model of slake durability characteristics for the different rock materials in the Patonga Claystone, providing a relatively simple basis for predicting longer-term stability in a range of geotechnical studies.

[Truncated abstract] The axial performance of piles in sand remains an area of great uncertainty in geotechnical engineering. Over the years, database studies have shown that the existing method for offshore piles (e.g. API 2000) is unreliable. There is therefore a clear need for an improved predictive method, which incorporates the state-ofthe- art understanding of the underlying controlling mechanisms. This Thesis is dedicated to address the factors influencing the end bearing performance of displacement piles in siliceous sand with a view to proposing and justifying an improved design formulation. Firstly, a database of displacement pile load tests in sand with CPT data was compiled in collaboration with James Schneider (Schneider 2007). It features the widest database with also the latest available pile load test data (e.g. Euripides, Ras Tanajib, Drammen etc) in electronic form. Evaluation of the three new CPTbased methods (Fugro-05, ICP-05 & NGI-05) against this database has revealed a broadly similar predictive performance despite their end bearing formulations being remarkably different. This anomaly promoted the author to extend the database to include additional tests with base capacity measurements to form new base capacity databases for driven and jacked piles, which resulted in the UWA- 05 method for end bearing of displacement piles in sand. This method accounts for the pile effective area ratio, differentiates between driven and jacked piles, and employs a rational qc averaging technique. ... Field tests were performed in Shenton Park, Perth to supplement the database study and, in particular, to examine the effect of the incremental filling ratio (IFR). 10 open-ended and 2 closed-ended piles were tested in compression followed by tension. The test results provide strong support for the UWA-05 method for base capacity evaluation employing the CPT qc values and the effective area ratio. A series of jacked pile tests was carried out on the UWA beam centrifuge, to further explore the factors affecting pile base response. In total, four uniform and four layered centrifuge samples were prepared and tested at various stress levels and relative densities using three separate pile diameters. The resistance ratio (qb0.1/qc,avg) is found to be independent of the absolute pile diameter, effective stress and soil relative density. The tests in layered soil enabled quantification of the reduction in penetration resistance when a pile/cone approaches a weak layer and revealed the significant influence on base stiffness of underlying soft clay layers. The stiffness decay curves (G/GIN vs. w/D, where GIN is initial operational shear stiffness) measured in static load tests were found to vary with ratios of GIN/qc, while there was a unique relationship between G/GIN and qb/qc. A detailed parametric study was carried out (using the FE code PLAXIS) by idealising pile penetration using a spherical cavity expansion analogue in layered soil. The numerical predictions compare well with the centrifuge results and their generalization enabled guidelines to be established for end bearing in layered soil.

Acompanha 1 mapa anexo / Orientador: Fábio Augusto Gomes Vieira Reis / Banca: José Eduardo Zaine / Banca: Oswaldo Augusto Filho / Resumo: Os escorregamentos são movimentos de massa recorrentes na Serra do Mar. Quando ocorrem de forma generalizada podem causar prejuízos e perdas de vidas, como no acidente ocorrido no município de Caraguatatuba (SP) em 1967. Com o intuito de evitar estes danos, na literatura, são propostos vários métodos para analisar e prever a ocorrência destes processos. Diante do exposto, o objetivo principal desta pesquisa consiste em analisar a suscetibilidade a escorregamentos na região entre Caraguatatuba e São Sebastião (SP), utilizando a compartimentação fisiográfica e a análise quantitativa. Para alcançar estes objetivos foi realizada a análise e compartimentação do terreno e a análise quantitativa dos fatores condicionantes (declividade, hipsometria e geologia) e da compartimentação fisiográfica. Foram testados, em ambiente SIG, diversos cenários a partir de dois métodos distintos. No Método 1, os fatores condicionantes foram analisados através de pesos de influência. No Método 2, os fatores condicionantes mantiveram os mesmos pesos do Método 1 e foram somados pesos para as classes de cada fator. A compartimentação fisiográfica definiu 16 unidades. Os resultados demonstraram que a maioria dos escorregamentos se concentraram na unidade fisiográfica IV e que há um controle topográfico na distribuição dos escorregamentos entre 100 e 400 m de altitude, em encostas com declividade entre 15º e 30º, compostas por gnaisse migmatítico e granito-gnaisse. Os mapas elaborados a partir do Método 2... (Resumo completo, clicar acesso eletrônico abaixo) / Abstract: Landslides are recurrent mass movements in the Serra do Mar. When they occur in a generalized way, as in the event occurred in Caraguatatuba city (SP) in 1967, they can cause a lot of environmental damage and deaths. In order to avoid this damage, several methods were proposed to analyze and predict the occurrence of this process. Considering the above, the main objective of this research is to analyze the susceptibility to landslides in the region between Caraguatatuba and São Sebastião (SP), using physiographic compartmentalization and quantitative analysis. In order to achieve these objectives, a physiographic analysis of the study area was carried out by the method of physiographic compa(...) / Mestre