Fine grained soils, in particular clays of high plasticity, are known to have very low values of hydraulic conductivity. This low permeability causes several problems related to vegetation growth and stormwater runoff. One way to improve the permeability of clay soils is by using coarse aggregates as a fill material. Recently, Expanded Shale has been widely applied as an amendment to improve drainage properties of clayey soils. However, limited effort has been made to quantify the effect of Expanded Shale on the hydraulic conductivity or on the volume change of fine grained soils. Specifically, the field and laboratory tests required to quantify the amounts of Expanded Shale to be mixed with clays to obtain desired hydraulic conductivity values have not been conducted. This paper presents the results of a series of laboratory fixed-wall permeameter tests conducted on naturally occurring clay deposits in the Austin area with different plasticity. The testing program comprised of clay samples with different quantities of Expanded Shale aggregates by volume, ranging between 0 and 50%, and compacted at two different compaction efforts (60% and 100% of the standard Proctor compaction effort). The laboratory test results indicate that the hydraulic conductivity of the three soils increases by at least an order of magnitude when the Expanded Shale is mixed in quantities between 25 to 30% by volume depending on the compaction effort. Expanded Shale amended samples also showed lower swelling potential with increasing amendment quantities. Moreover, when the clay with the higher plasticity was mixed with 25% Expanded Shale, the compression and recompression ratios decreased by 25% and 15% respectively. / text

This research focused on designing a grout mixture using lightweight aggregate that achieves the minimum 28-day compressive strength required for normal-weight grout, 2000 psi. This research specifically studied the effects of aggregate proportion, slump, and aggregate soaking on the compressive strength of the mixture. The variable ranges investigated were 3-4.75 parts aggregate to cement volumetrically, 8-11 in. slump, and 0 and 2 cycles of soaking. The statistical model developed to analyze the significance of variable effects included a three-way interaction between the explanatory variables. All three explanatory variables had a statistically significant effect on the grout compressive strength, but the effect of soaking was minimal and decreased as aggregate proportion decreased. This research also showed that lightweight grout, when prepared using aggregate proportion and slumps within the ranges suggested in American Society for Testing and Materials C476, reaches the required minimum 28-day compressive strength with a factor of safety of at least 2.7.

Light-weight aggregate has been used successfully for structural and non-structural applications, and its most common use has been in light-weight concrete. Limited research has been done on light-weight grout though and there are no standards in place. The research performed in this study is intended to increase the knowledge of light-weight grout specifically made with expanded shale aggregate. The research presented herein is a pilot study and consists of preliminary aggregate and grout testing that resulted in the mix design of six grout types: three fine grout designs and three coarse grout designs. Conventional normal-weight aggregate was employed in the first grout mix. A light-weight aggregate batch was made with the same material proportions, as well as the same target water-cement (w/c) ratio and cement content. The weight of the cement was increased by 30 percent in the third grout type of each set to determine the effect on strength. The slump, component temperature, unit weight, air content, segregation, cement content, w/c ratio, and compressive strength for each grout type was gathered throughout testing. Correlations between grout testing results are examined and discussed. In addition, the effectiveness of expanded shale grout, other light-weight grouts, and normal-weight grout with respect to compressive strength to cement content ratio are determined. Results of the testing show that all six grout types studied in this research reached the minimum 28-day strength of 13.8 MPa (2000 psi) ASTM standard. In addition, the results indicate that the cement content in expanded shale light-weight grout would need to be increased to reach comparable compressive strengths to that of the normal-weight grout. The comparison between the compressive strength to cement content ratio of the different grouts indicate that normal-weight grout is more efficient. In addition, light-weight grout made with blast furnace slag grout is slightly more efficient than that made with expanded shale; however, this observation was only possible after several crucial assumptions were made about an existing blast furnace slag study. These strength-cement ratios do not account, however, for the benefits of reduced dead loads, improved thermal insulation, and improved sound insulation that could potentially influence the choice of the material used in and the life-cycle cost of the construction. Additional research should be done to verify the results of the ratios and the assumptions made herein. Furthermore, a life-cycle analysis needs to be conducted before a definite conclusion is made about which type grout is more efficient.

<p>To make bacterial-based self-healing concrete, alkaline-resistant bacterial spores, nutrient sources, and a calcium source are incorporated into a concrete matrix. Two ureolytic spore-forming bacteria, <i>Sporosarcina pasteurii</i>, <i>Lysinibacillus sphaericus</i>, and two non-ureolytic spore-forming bacteria, <i>Bacillus cohnii</i>, and <i>Bacillus pseudofirmus</i>, which have been used in previous studies as bacterial concrete healing agents, were compared in this study. The four bacteria were compared for their (1) sporulation rates on different sporulation agar plates, (2) growth in five liquid media, (3) survival rates in light weight aggregates (LWA) and in mortar samples, and (4) calcium carbonate precipitation rates from either calcium lactate or calcium nitrate. Sporulation was successfully induced after three-day incubation at 30°C on an appropriate sporulation medium. High sporulation rates of <i>B. cohnii</i>, and <i>B. pseudofirmus</i>(93% and 99% respectively) were found on alkaline R2A medium (AR2A). A sporulation rate (89%) of <i>S. pasteruii</i>was observed on tryptic soy agar supplemented with 2% urea (TSAU)<i>.</i>The highest sporulation rate (60%) of <i>L. sphaericus</i>was found on R2A medium supplemented with 2% urea (R2AU). In the growth study, tryptic soy broth supplemented with 2% urea (TSBU) was a positive control which supported rapid growth of all four bacteria. <i>Sporosarcina pasteurii </i>and <i>L. pasteurii</i>showed rapid growth rates in alkaline yeast extract broth (AYE) and yeast extract with 2% urea broth (YEU) respectively. In contrast, <i>B. cohnii</i>, and <i>B. pseudofirmus</i>grew poorly in all media except in the positive control. Viable counts of the four bacterial spores reduced (1.8–3.3 logs) during the first 24 h in mortar samples and then remained stable for next 27 days testing period. Among the four, <i>S. pasteurii</i>showed the smallest reduction of viable counts (1.8–2.5 logs) in mortar after one day of incubation. Both <i>S. pasteurii</i>and <i>L. sphaericus</i>showed high CaCO₃productions (>80%) after 24 h incubation at 30°C in YEU containing either calcium nitrate or calcium lactate. However, <i>B. pseudofirmus</i>and <i>B. cohnii </i>showed<i></i>low calcite recovery rates (<11%) in AYE containing either<i></i>calcium nitrate or calcium lactate under the same incubation condition. Overall, <i>S. pasteurii</i>was the best bacterial concrete healing agent of the four. This bacterium had (1) rapid growth rate in AYE, (2) about 90% sporulation rate within 3 days, (3) highest survival rates after 24 h in mortar samples and, (4) high CaCO₃precipitation rates, 82 or 98%, in broth containing calcium nitrate or calcium lactate respectively.</p><p>In addition, two different lightweight aggregates (LWA), expanded shale (ES) and expanded clay (EC), which were used as bacterial carriers and protective materials, were compared in this study. Each type of LWA was separated into three sizes (<0.85 mm, 0.85– 2.0 mm, and >2.0 mm) and immobilized with spores of <i>B. cohnii</i>or <i>B. pseudofirmus.</i>Viable counts recovered from EC and ES reduced <1.0 log after the immobilization process and remained stable during the 150 days testing period. Neither the type nor the particle sizes of the two LWA significantly affected the survival rates of the bacterial spores. This result showed that both EC and ES could be used as carriers for bacterial healing agents. It was also found that when the spores were immobilized with nutrients in LWA, their survival rates in mortar samples can be improved slightly (<1.0 log).</p><p><br></p>