O melhor comportamento de uma estrutura de solo reforçado com geossintéticos não depende só da elevada resistência à tração da inclusão, mas também da sua rigidez e do nível de carregamento sob o qual a estrutura está submetida. Dessa maneira, a interação entre o reforço e as respectivas camadas de solo ao seu redor torna-se de grande importância, pois a mobilização cisalhante combina a deformação da interface solo-reforço e o alongamento do geossintético. Sendo que a melhor forma de avaliar a interação entre o solo e a geogrelha é por meio de ensaios de arrancamento, pensa-se na realização de ensaios de arrancamento cíclico para analisar a interação dinâmica entre o solo e a inclusão quando certas estruturas são submetidas a esse tipo de solicitação. Por causa disso, o objetivo principal deste trabalho é analisar o efeito produzido por carregamentos monotônicos e cíclicos de interface numa geogrelha biaxial de polipropileno, quando inserida na interface de um solo argiloso e um solo arenoso sob diferentes tensões de confinamento. Para isso, são utilizados os equipamentos de pequenas e grandes dimensões do Laboratório de Geossintéticos da EESC-USP, visando avaliar a sua relação e a viabilidade de uso do equipamento de pequenas dimensões. Inicialmente foram realizados ensaios de arrancamento monotônico em ambos os equipamentos sob tensões de confinamento de 25, 50 e 100 kPa, sendo que as resistências obtidas com as tensões de 25 e 100 kPa permitiram definir as amplitudes do carregamento cíclico correspondentes ao 20% de tais valores. Adicionalmente, após a aplicação dos 10.000 ciclos de carga correspondentes à capacidade do equipamento, foi aplicado novamente um carregamento monotônico com o intuito de determinar o efeito do carregamento dinâmico na resistência ao arrancamento e assim poder realizar as respectivas comparações com os valores iniciais. Com base nos resultados obtidos, foi possível observar a diferença no grau de confinamento entre ambos os equipamentos, sendo maior no de grandes dimensões por causa da melhor distribuição das tensões sobre a área ocupada pela geogrelha. Adicionalmente, o grau de confinamento em ambos os equipamentos também influenciou a diferença no efeito do carregamento dinâmico, sendo de desconfinamento no de grandes dimensões e de densificação no de pequenas dimensões. / The best behavior of a reinforced soil structure with geosynthetics not only depends on the high tensile strength of the inclusion, but also on its rigidity and the loading level in which the structure is subjected. Thus, the interaction between the reinforcement and the respective layers of soil around, becomes very important because the shear mobilization combines the deformation of the soil-reinforcement interface and the lengthening of the geosynthetic. Since the best way to assess the soil-geogrid interaction is through pullout tests, it is thought in performing cyclic pullout tests to examine the dynamic soil-inclusion interaction when some structures are submitted to that kind of loads. Because of that, the main objective of this work is to analize the effect that is produced by monotonic and cyclic interface loading on a biaxial polypropylene geogrid, when it is inserted into the interface of a clayey soil and a sandy soil under different confinement stresses. For that, the small and large dimensions equipments of the Geosynthetics Laboratory at EESC-USP are used, looking to evaluate their relationship and the feasibility of using a small dimensions equipment. Initially, they were performed monotonic pullout tests in both equipments under confinement stresses of 25, 50 and 100 kPa, wherein the pullout strengths obtained with 25 and 100 kPa allowed the definition of the load cyclic amplitudes, which corresponded to 20% of such values. Additionally, after applying 10.000 load cycles, corresponding to the capacity of the equipment, it was applied a monotonic loading in order to determine the dynamic loading effect on pullout strength, being useful to compare such values with the initial response. Based on the obtained results, it was possible to observe the difference in the confinement degree between both equipments, being higher in the large one because of the better stress distribution on the geogrid area. Aditionally, the confinement degree in both equipments also influenced the difference in the dynamic loading effect, being deconfinement in the soil-geogrid interface of the large one and densification in the other one.

Scrap tyres provide numerous advantages from the viewpoint of civil engineering practices. Scrap tyres are light weight, have high vibration absorption, high elastic compressibility, high hydraulic conductivity, and temperature isolation potential. Scrap tyres have a thermal resistivity that is about seven times higher than soil; they produce low earth pressure and absorb vibrations. Many new techniques have emerged with time to utilize these advantageous characteristics for practical purposes in civil engineering. Though current reuse and recovery of scrap tyres has reduced the amount of landfills, but still there is a need for developing additional practices for the reuse of scrap tyres. Moreover, most of present practices do not use its vibration absorption capacity efficiently. To use the scrap tyres as individual material or mixed with soil in civil engineering applications, the systematic understanding of static and dynamic properties of sand-rubber mixtures (SRM) are of prime importance. In the present study an attempt has been made to characterize the SRM to use them as low-cost isolation material for low-to-medium rise buildings. Proposal of this isolation system using SRM is addressed in this study in four parts; in the first part, the estimation of shear strength and volumetric characteristics of the SRM were carried out. A total of seven different rubber sizes (six sizes of granulated rubber; 2 - 1 mm; 4.75 - 2 mm; 5.6 - 4.75 mm; 8 - 5.6 mm; 8 - 9.5 mm; 12.5 - 9.5 mm and one size of tyre chips; 20 - 12.5 mm) were considered for characterizing the SRM, and the rubber size which has higher shear strength characteristics is identified as optimum size for further studies. Second part deals with the effect of reinforcement on SRM with higher rubber content (50% and 75% rubber by volume). In the third part, dynamic properties of selected SRM combination with and without reinforcement were generated from experimental studies. In the last part, the numerical analysis was carried out using finite element program Strand7 to find out optimum dimension of proposed isolation scheme and reduction of spectral accelerations. In addition, the laboratory model tests were also carried out on square footing supported on unreinforced and reinforced SRM. The relative performances of reinforcement on settlement characteristics of SRM for 50% and 75% SRM have been compared with unreinforced SRM. Engineering behaviour of SRM has been studied by considering different rubber sizes and compositions by carrying out large scale direct shear test and Unconsolidated Undrained (UU) triaxial test. The shear strength characteristics such as peak shear stress, cohesion, friction angle, secant/elastic modulus, volumetric strain, failure and ultimate strength, ductility/brittleness index, and energy absorption capacity of sand and SRM were determined. The optimum percentage rubber content based on maximum shear strength and energy absorption capacity has been arrived. The granulated rubber size (12.5 - 9.5 mm) and percentage ratio, 30% by volume is found to be optimum size and content, which gives the maximum energy absorption capacity and lower brittleness index values compared to other rubber sizes. This chapter also describes the applicability of concept of Response Surface Methodology (RSM) to identify an approximate response surface model from experimental investigations on the engineering properties of sand and SRM. The experimental data were quantitatively analyzed by multiple regression models by correlating response variables with input variables in this study. To consume more tyres in SRM, rubber mix of 50 % and 75 % mixes are studied and these SRM results in lower shear strength and higher volume change when compared to 30 % SRM. To improve shear strength and reduce compressibility, geosynthetic reinforcement study has been carried out for 50% and 75% rubber by volume. Here geotextile, geogrid and geonets were used as reinforcement and number of layers and spacing between layers were varied. Finally type of reinforcement, number of layers and optimum spacing are arrived for the optimum rubber size of 12.5 - 9.5 mm for reinforced SRM. This study found that 4 layers with equal spacing of geotextile for 50 % SRM and geonet for 75 % SRM shows better strength when compared to other combinations. Further dynamic properties such as shear modulus and damping values at different strain level are estimated for red soil, sand, 30 % SRM and unreinforced and reinforced 50 % and 75 % SRM by carrying out resonant column tests and cyclic triaxial tests. The normalized shear modulus and damping ratio curves have been developed for these materials. The experimental results indicate that, shear modulus increases for 30% rubber by volume when compared to sand, thereafter the shear modulus values decreased with a further increase in rubber content in SRM. Whereas the damping ratio increases with increasing rubber content in SRM. For sand and SRM, with an increase in confining pressure shear modulus increases and damping ratio decreases. Based on the comprehensive set of experimental results, a modified hyperbolic model has been proposed. These properties are further used in the numerical analysis to find out the effectiveness of SRM as isolation material. Numerical dynamic analysis has been carried out on a 2-D finite element model of the soil-foundation-structure system. The building model has been generated considering the typical G+2 building resting on 20 m thick soil followed by rock depth and foundation is placed at 2.0 m below ground level. The beams and columns in the superstructure are modeled using 2-D frame elements. The soil column has been modeled using 4-noded 2-D plane strain plate elements. Considering the transmitting boundary condition, viscous dampers are implemented at the base of the computational soil domain in order to mitigate the reflective effects of waves. The Newmark family method (average acceleration method) has been used to calculate the displacement, velocity and acceleration vectors. Comprehensive numerical simulations have been carried out on the soil-foundation-structure system by varying rubber content in SRM (30%, 50% and 75% granulated rubber by volume), depth and thickness of SRM around footing and considering two input earthquake acceleration time history. It was found that earthquake vibrations are considerably reduced for SRM with higher rubber content. The optimum dimension of SRM giving maximum reduction in shaking level is found to be 3B below the footing and 0.75B (where B is the width of footing) on the side of the footing. Generally, the shaking levels at different floor can be reduced by 30-50%, with the use of 75% SRM. The results also indicated that the effectiveness of proposed system would depend on the characteristics of ground motion. To study the bearing capacity of square footing on SRM, laboratory model tests were carried out on square footing supported on unreinforced and reinforced SRM. The SRM combination which have been used for numerical studies are used in this model studies to know the bearing capacity and settlement characteristics. The optimum dimension of SRM around footing has been constructed. Model tests results show that, the bearing capacity decreases and settlement increases steadily with the increase in rubber content in SRM. Addition of reinforcement to SRM significantly improved the bearing capacity and reduced settlement characteristics. Reinforced SRM may be used as an effective low cost isolation scheme to reduce earthquake vibrations.

Clays are used for long for the control of soil and water pollution as they are inexpensive natural materials with a high adsorption capacity for a wide range of pollutants. However their use as components in engineered waste containment systems is often limited when it comes to the control of organic contaminants as the clays are organophobic in nature. Organic modification of the natural clays, by replacing the exchangeable inorganic cations of clay with organic cations, can facilitate to overcome this limitation. On modification the clays become organophilic which can enhance their sorption capacities for organic contaminants. There are several ways by which natural clays can be modified with organic cations. The type of clay, the type of modifier, and the extent of modification play an important role in enhancing the organic sorption capacity. Sorption of organics by the organo clays depends on a large extent on the specific interactions that occur between modified clay and the organic contaminants. The interaction between the clay and the contaminants depend on the physico-chemical properties of modified clay and nature of organic contaminants. Since the properties of natural clays are likely to be altered by the modification a detailed study has been taken up to understand the physico chemical characteristics of organo clays which essentially control their organic sorption efficiency. Apart from bentonite which is widely used as a component of barrier systems, the characteristics of other types of clays on organic modification also needs to be assessed as they can also form part of the containment system frequently. Further the modification of clays is bound to bring in significant changes on their geotechnical properties which may affect their performance when used as barrier material. Only limited research has been conducted in the past on the geotechnical characteristics of organo clay. Therefore extensive studies have been carried out on the evaluation of the geotechnical characteristics of organo clays and the effect of organic modification on important geotechnical properties. Since very often inorganic and organic contaminants can occur simultaneously, admixtures of bentonite and organically modified clays needs to be employed as a part of clay barrier system. Moreover clay alone is very rarely used as component of barrier systems and significant portion of barrier material usually include non clay fraction. Hence studies have been carried out on mixtures containing different proportions of organo clay and bentonite and sand – organo clay / bentonite to evaluate their geotechnical behavior. Important geotechnical properties considered for detailed studies are swelling, compressibility and permeability. Detailed studies on the organic sorption capacities of different organically modified and unmodified clays, mixtures of bentonite and organo clays have also been conducted. The results of studies conducted are presented in 9 chapters. The organization of the thesis is as follows: Chapter 1 gives detailed background information on the sources and hazards of organic contaminants, inadequacy of conventional barriers to contain organic contaminants, the need for modification of natural clays, and the methods for organic modification of clays. Extensive review of literature has highlighted the need to study the effect of organic modification on the physico chemical and geotechnical properties of clay in different pore fluids. Organo clays were prepared using a wide range of clays viz., two types of bentonites of different regions, black cotton clay and commercially available kaolinite with a long chain organic cation. The extent of organic modification was varied by varying the amount of organic cation exchanged as function of total cation exchange capacity of the clays. Detailed physico chemical characterization of these modified and unmodified clays has been carried out with the help of different state of art techniques. The Chapter 2 brings out the effect of modification, role of type of clay and type of modifiers on the characteristics of organo clays by comparing the physico chemical characteristics of different modified and unmodified clays. The organic modification of montmorillonitc clays with long chain organic cation is found to increase their lattice spacing with the amount of modification whereas no such increase was observed on modification of kaolinitic clays even when all the exchangeable inorganic cations were replaced with the organic cations. The XRD studies revealed that the intercalated organic cations of the modified montmorillonite clays assumed mono, bi, or pseudo tri layer depending on the extent of organic modification. Irrespective of the type of clay modified or the modifier used all the organo clays tend to become e hydrophobic, and the surface area of the clays was found to decrease. A comparison of the characteristics of clays modified in laboratory with organo clay obtained commercially revealed that the organic modification was more effective for the organo clay prepared in the laboratory. As the index properties of all clays are generally correlated with their geotechnical characteristics, the effect of organic modification on the index properties of clays was studied. Chapter 3 presents the effect of organic modification on the plasticity and free swell behavior of clays. The index properties of commercially available organo clay and the unmodified clay used for its preparation were evaluated with pore fluids of different dielectric constants. Fluids of varied dielectric constants were chosen as it is one of the important characteristics to understand the behavior of clays. It was observed that the organic modification of clays reduced the plasticity of the clays in water and increased the plasticity in less polar liquids like ethanol. As the organo clays are more hydrophobic, the water holding capacity and plasticity in water is decreased to a large extent. The free swell behavior of clays in different pore fluids were assessed in terms of the modified free swell index. It was found that trend of variation of free swell index with dielectric constant for modified and unmodified clays, as in the case of plasticity is quite opposite. The swell volume of the modified clays was observed to be controlled more by surface solvation than by the development of the inter particle repulsive forces and diffused double layer. The effect of incorporating unmodified bentonite with organically modified clay on the index properties of bentonite has also been studied. The results suggested that the effect of organo clay addition to bentonite was always to reduce its plasticity and free swell in water. However in pore fluids of lower dielectric an increase in the plasticity and free swell was observed with increasing organo clay content in the mixture. This owes to the fact that organo clays can interact strongly with organic fluids, changing its fabric arrangement. As reported from literature it is well established that the swell of clays has conflicting role on the stability and permeability of clay barriers. Swelling of clays is liable to cause a reduction in hydraulic conductivity, enhance the retention times of contaminants and attribute self healing capacity to the liners. Even though extensive studies have been carried out on the swell behaviour and mechanism of swell of unmodified clays, no systematic research is reported on the effect of organic modification on swell behavior of clays especially in the presence of different pore fluids. Chapter 4 describes the results of oedometer swell tests carried out on compacted samples of modified, unmodified clays and organo clay –bentonite mixture in the presence of different pore fluids such as water, ethanol, and their mixture and carbon tetra chloride. Swelling ability of the unmodified clays was not completely suppressed even in the presence of low polar miscible organic liquids as they were molded at water contents corresponding to the optimum moisture content (OMC). The order of the swelling for the unmodified bentonites was in the order of the polarity of the pore fluids used, while the order is reversed upon organic modification of clays. The mechanism of swell in the case of organo clays in organic liquids was related to the solvation of the organic liquid by the intercalated organic cations. And unlike in the case of unmodified clays, the organo clays showed “solvent induced swelling”. Both organic modification and addition of organo clay to bentonite resulted in the suppression of the swelling of clays in water irrespective of the type of modifier or the extent of organic modification. The Chapter 5 gives a detailed account of the compressibility behavior of organically modified clays and its mixtures with bentonite when the samples were molded with water at their respective OMC and later inundated with different fluids. Significant differences were observed on the compressibility of modified and unmodified clay in different fluids. Organic modification of clays reduced their affinity to water and resulted in lowering the compressibility. However there was an increased compressibility for the organo clays when the samples were inundated with non polar liquids and the compression of the organo clay in non polar fluid was not influenced by the nature of clay nor by the type of modifier. The compressibility of the mixtures of organo clay and bentonite in non polar liquids was generally controlled by the organo clay component of the mixture. Organo clays can be recommended as additives in bentonite slurries for construction of slurry walls in order to improve the containment of organics. But the amendment should not compromise the stability and integrity of the slurry walls. Moreover the influence of addition of sorptive material like organo clay on the compressibility behavior of bentonite slurry has received little attention and needs serious consideration as the studies in the previous chapter has brought out that the compressibility of compacted bentonite reduced significantly on organic modification as well as on addition of orgno clay. The Chapter 6 deals with the compressibility behavior of slurries of unmodified bentonite, organo clay, and their mixtures molded with respective liquid limits with water and later inundated with fluids of different dielectric constants as the slurries frequently get in contact with fluids other than water during their operational life. However it was observed that the effect of polarity of the inundating liquid is masked in all the cases by the presence of large amount of initial molding water as the possible specific chemical interactions between organo clay and non polar fluids were restricted in the presence of large amount of molding water. But the slurry samples molded and inundated with non polar carbon tetra chloride showed that the organo clay samples are more compressible when molded with carbon tetrachloride. The chapter also gives a brief discussion on the effect of initial molding water content on the compressibility of organo clays and its mixtures. The compression was found to increase with increase in initial water content irrespective of the type of inundating fluid in agreement with the behavior observed in the case of unmodified clays. However the effect was less pronounced at higher applied pressures. The Chapter 7 brings out the volume change behavior of organo clay amended sand bentonite mixtures (SOB) which form potential barrier to prevent and /or remove contaminants. The compaction behavior of mixtures showed that the degree of compaction achieved was controlled mainly by the sand content and proportion of organo clay in the total fine fraction. The volume change behavior of the SOB mixtures were assessed with the help of oedometer tests conducted on mixtures compacted at OMC conditions and inundated with different fluids same as those used for the swell tests. The samples with higher sand content showed no observable swell when inundated with liquids viz., water, ethanol and their mixture as all the swollen finer particles were accommodated in the voids created by sand particles. However a high swell percentage was measured when samples with high organo clay content were inundated with carbon tetrachloride. Moreover with increased amounts of organo clay in the mix the swelling of bentonite was suppressed and the same trend continued even when the pore fluids were changed to liquids of medium polarity. The organo clays are capable of interacting strongly with non polar liquids like carbon tetra chloride, and hence an appreciable swell was noted when inundated with them especially in the case of mixtures with high organo clay content. The swell behavior of SOB mixtures with lower sand contents were controlled mostly by the interaction of the pore fluid with bentonite and organo clay, interactions between organo clay and bentonite and the polarity of the pore fluid. As the pore fluid polarity was decreased the influence of organo clay component of the mixture was more pronounced. The Chapter 8 explains the hydraulic performance of modified and unmodified clays along with that of the mixtures of organo clay with bentonite and SOB. The coefficient of permeability was calculated from the consolidation data obtained on sample molded at OMC. The permeability variations observed on changing the pore fluids were studied at each applied pressure. The hydraulic conductivity showed a decreasing trend with the increase in applied pressure for all the clays. The specific interactions of the organo clay with the pore fluids and the clay content were found to play a role in controlling the permeability. Limited tests were carried out to simulate a condition where a SOB liner is proposed as a secondary liner below a punctured geo membrane and its hydraulic performance was evaluated with diesel and water as pore fluids. The permeability coefficients with diesel as permeant were observed to decrease with increase in organo clay content of the mixture irrespective of the applied pressure where as the reverse was true when permeated with water. Thus the use of SOB as secondary liner below storage tanks so as to control the transport of contaminants leaking containments systems is established. The organic sorption efficiency of the modified and unmodified clays and the mixture were evaluated in terms of removal of total organic carbon (TOC) and reduction in chemical oxygen demand (COD) of the different leachates including municipal solid waste (MSW) leachate when treated with different types of modified and unmodified clays. All the modified clays irrespective of the type of clay or the type of modifier used showed improved organic sorption capacity. The sorption of TOC was found to follow a linear sorption mechanism in the case of organo clays and the organic contaminants were partitioned on to the organic phase attached to the organo clays. The composition, age and type of leacahte played a major role in controlling the organic sorption efficiency of organo clays in the case of MSW leachates. The studies done with different mixtures of organo clay and bentonite and SOB mixtures clearly proved that the addition of organo clay always enhanced the organic sorption efficiency of the mixtures. The results are discussed in Chapter 9. The Chapter 10 highlights the major conclusions drawn from the study. The study, apart from satisfying the research zeal on understanding the behavior of organo clays, has generated important information useful for the geo environmental engineer to arrive at appropriate design of barrier systems incorporating organically modified clay, based on the characteristics of pore fluid.

Efficient road network and connectivity play vital role in the development of any country. Majority of the rural roads are unpaved and connectivity of rural roads is always a major challenge. Unpaved roads are also used for temporary transportation facilities like access roads, haul roads for mines, forest roads and parking lots. Since these roads do not have asphalt surfacing, they are subjected to early failures due to distresses like rutting, pot holes and depressions . Stabilization of unpaved roads using geosynthetics has been proved to be promising in increasing the lifespan of these roads because they facilitate economical, aesthetic and effective design of the roads. Inclusion of geosynthetic layers at the interface of subgrade soil and granular sub-base, reduces the surface heave, ensures a better stress distribution and reduces the stresses transferred to the subgrade soil, as demonstrated by earlier researchers. Wide variety of geosynthetics like woven and nonwoven geotextiles, uniaxial and biaxial geogrids and geocells are used as reinforcement in road sections. Geotextiles improve the strength by interfacial friction, lateral restraint and membrane effect. Geogrids provide additional benefit of interlocking. Geocells are honeycomb shaped geosynthetic cellular confining systems filled with aggregates in which the reinforcement action is derived not only by friction and interlocking, but also by confinement. Load-deformation characteristics of reinforced soil-aggregate systems under static, repeated and cyclic loads is a potential topic of interest considering the fact that the design of geosynthetic reinforced unpaved roads is still under development and experimentation. The objective of the present study is to understand the beneficial use of geosynthetics in unpaved roads and to provide clear insight into the influence of geosynthetics on the cyclic loading characteristics of unpaved roads through laboratory experiments. California Bearing Ratio (CBR) tests were carried out on unreinforced and reinforced soil-aggregate systems to study the effect of various parameters such as type of reinforcement, form of reinforcement, quantity of reinforcement, and water content of the subgrade soil on the load-penetration response of the various systems. Modified CBR tests were also carried out to understand the influence of boundary of the mould and anchorage of reinforcement on the behavior of reinforced soil-aggregate systems. Behavior of unreinforced and reinforced soil-aggregate systems under repeated and cyclic loading is also studied to understand the resilience of the composite systems. From the measured stress-strain response, the elastic and plastic strains developed in various systems are compared. Different moduli such as secant modulus, cyclic modulus and resilient modulus are computed for different systems and compared. To investigate the effectiveness of geosynthetics in improving the load - bearing capacity, repeated load tests were carried out on model sections of unpaved road constructed in a steel test tank of size 750 mm × 750 mm × 620 mm. The effect of various parameters like the form of reinforcement, quantity of reinforcement, height of geocell layer and the position of geocell layer on the load-deformation behaviour of the unpaved model road sections was studied. Static and cyclic triaxial tests were carried out on unreinforced and reinforced granular sub-base materials to understand their stress strain behavior under static and cyclic loading conditions. The influence of quantity and form of reinforcement on the stress-strain behaviour of these materials was studied. From the studies it is observed that the use of reinforcement increases the CBR value of the soil-aggregate systems. Studies with two different sizes of CBR moulds indicated that the boundary effect in the standard CBR mould leads to the overestimation of the CBR value, resulting in unconservative design of road sections. Providing anchorage to the reinforcement in CBR tests did not produce an appreciable change in the load-penetration behavior. From the repeated load tests it was observed that the reinforced systems did not show any improvement in the load-deformation behaviour at low levels of rut depth. At higher rut depths, the reinforced systems developed less plastic settlements and more elastic settlements and low resilient modulus compared to unreinforced systems. From the model tests on unpaved road sections, it was observed that the improvement in the cyclic load resistance of the road due to the inclusion of geocell layer depends on the height of the geocell layer and its position. Increasing the height of geocell layer resulted in improved performance up to certain height of the geocell layer, beyond which, further increase in the height reduced the load resistance because of the inadequate granular overlay thickness and inadequate compaction of aggregate within the geocell pockets. Static and cyclic triaxial tests showed that the geogrid and geocell reinforced granular sub-base material sustained higher peak stresses and exhibited increase in modulus compared to the unreinforced specimens. Results of element and model tests carried out in this study gave important insight into the load-deformation characteristics of reinforced soil-aggregate systems under static, repeated and dynamic loads. The results provide guidelines regarding the selection of type, quantity and configuration of geosynthetic reinforcement while designing unpaved roads and the expected performance of these reinforced unpaved roads.

The various aspects of the 3D cellular confinement systems (geocells) subjected to static loading are comprehensively studied with the help of experimental and numerical studies. The performances of the geocells were separately studied in both sand and clay beds. Laboratory tests were performed on single as well as multiple cells. The behavior of 3D-cells made of different materials such as Novel polymeric alloy, geogrids and bamboo were compared. Moreover, the performances of the geocells were compared with other forms of geosynthetic reinforcements namely, geogrids and the combination of geocells and geogrids. In addition to comprehensive experimental study, 2-dimensional and 3-dimensional numerical modelling efforts are also presented. A Realistic approach of modelling the geocells in 3D framework has been proposed; which considers the actual curvature of the geocell pockets. An Analytical equation has been proposed to estimate the increase in the bearing capacity of the geocell reinforced soft clay beds. Similarly, a set of equations to estimate the stress and strains on the surface of the geocells subjected to compressive loading were also proposed. A case study highlighting the innovative use of the geocell foundation to support the embankment on soft settled red mud has been documented in the thesis. A new and emerging application of geocell to protect underground utilities and the buried pipelines has been proposed. At the end, behavior of the geocell under cyclic loading has also been discussed. Firstly, laboratory model tests were performed to understand the behavior of the geocells in sand and clay beds. Test results of unreinforced, geogrid reinforced, geocell reinforced, and geocell reinforced with additional planar geogrid at the base of the geocell cases were compared separately for sand and clay beds. Results revealed that the use of geocells increases the ultimate bearing capacity of the sand bed by 2.9 times and clay bed by 3.6 times. Provision of the basal geogrid increases the ultimate load carrying capacity of the sand and clay bed by about 3.6 times and 4.9 times, respectively. Besides increasing the load carrying capacity, provision of the planar geogrid at the base of the cellular mattress arrests the surface heaving and prevents the rotational failure of the footing. Geocells contribute to the load carrying capacity of the foundation bed, even at very low settlements. In addition, the effect of infill materials on the performance of the geocell was also studied. Three different infill materials, namely aggregate, sand and local red soil were used in the study. Results suggest that the performance of the geocell was not heavily influenced by the infill materials. Out of which aggregate found to be slightly better than other two infill materials. Further, 2-dimensional numerical studies using FLAC2D (Fast Lagrangian Analysis of Continua in 2D) were carried out to validate the experimental findings. The equivalent composite approach was used to model the geocells in 2-dimensional framework. The results obtained from the FLAC2D were in good agreement with the experimental results. However, in the sand bed, FLAC2D overestimated the bearing pressure by 15% to 20% at higher settlements. In addition, the joint strength and the wall deformation characteristics of the geocells were studied at the single cell level. The study helps to understand the causes for the failure of the single cell in a cellular confinement system. Experimental studies were conducted on single cells with cell pockets filled up with three different infill materials, namely, silty clay, sand and the aggregates. The results of the experimental study revealed that the deformation of the geocell wall decreases with the increase in the friction angle of the infill material. Measured strain values were found to be in the range of 0.64% to 1.34% for different infill materials corresponding to the maximum applied bearing pressure of 290 kPa. Experimental results were also validated using FLAC3D. Findings from the numerical studies were in accordance with the experimental results. A simple analytical model based on the theory of thin cylinders was also proposed to calculate the accumulated strain of the geocell wall. This model operates under a simple elastic solution framework. The proposed model slightly overestimates the strains as compared to experimental and numerical values. A realistic approach of modelling the geocells in 3-dimensional (3D) framework has been proposed. Numerical simulations have been carried out by forming the actual 3D honeycomb shape of the geocells using the finite difference package FLAC3D. Geocells were modeled using the geogrid structural element available in the FLAC 3D with the inclusion of the interface element. Geocells, foundation soil and the infill soil were modeled with the different material model to match the real case scenario. The Mohr Colombo model was used to simulate the behavior of the sand bed while modified Cam clay was used to simulate the behavior of the clay bed. It was found that the geocells distribute the load in lateral direction to a relatively shallow depth as compared to unreinforced case. More than 50% reduction in the stress in the presence of geocells and more than 70% reduction in the stress in the presence geocells with basal geogrid were observed in sand and clay beds. The numerical model was also validated with the experimental studies and the results were found to be in good agreement with each other. The validated numerical model was used to study the influence of various properties of the geocells on the performance of the reinforced foundation beds. The performance of the foundation bed was directly influenced by the modulus and the height of the geocells. Similarly, the pocket size of the geocell inversely affected the performance of the reinforced beds. The geocell with textured surface yielded better performance than the geocell with smooth surface. A case history of the construction of a 3 m high embankment on the geocell foundation over the soft settled red mud has been documented. Red mud is a waste product from the Bayer process of Aluminium industry. The reported embankment is located in Lanjigharh (Orissa) in India. The geotechnical problems of the site, the design of the geocell foundation based on experimental investigation and the construction sequences of the geocell foundations in the field are discussed. Based on the experimental studies, an analytical model was also developed to estimate the load carrying capacity of the soft clay bed reinforced with geocell and the combination of geocell and geogrid. The solution was established by superimposing the three mechanisms viz. lateral resistance effect, vertical stress dispersion effect and the membrane effect. By knowing the pressure applied on the geocell, tensile strength of the geogrid and the limiting settlement, the increment in the load carrying capacity can be calculated. The analytical model was validated with the experimental results and the results were found to be in good agreement with each other. The results of the experimental and analytical studies revealed that the use of the combination of geocell and the geogrid is always beneficial than using the geocell alone. Hence, the combination of geocell and geogrid was recommended to stabilize the embankment base in Lanjigharh. Over 15,000 mof embankment base was stabilized using geocell foundation. The foundation work was completed within 15 days using locally available labors and the equipment. Construction of the embankment on the geocell foundation has already been completed. The constructed embankment has already sustained two monsoon rains without any cracks and seepage. Like Aluminum tailings (redmud), geocell foundations can also be used in various other mine tailings like zinc, copper etc. Geocell foundation can offer potential solutions to storage problems faced by various mining industries. The thesis also proposes a potential alternative to the geocells in the form of bamboocells in order to suit the Indian scenario. Indian has the 2nd largest source of bamboo in the world. The areas particularly rich in bamboo are the North Eastern States, the Western Ghats, Chattisgarh and Andaman Nicobar Islands. The tensile strength and surface roughness of the bamboo was found to be 9 times and 3 times higher than geocell materials. In order to use the bamboo effectively, 3D cells (similar to geocells) and 2D grids (similar to geogrids) are formed using bamboo known as bamboocells and bamboogrids respectively. The idea behind forming bamboocells is to extract the additional confining effect on the encapsulated soil by virtue of its 3-dimensional shape. The laboratory investigations were performed on a clay bed reinforced with natural (bamboo) and commercial (geosynthetics) reinforcement materials. The performance of bamboocells and bamboogrids reinforced clay beds were compared with the clay bed reinforced with geocells and geogrids. The ultimate bearing capacity of the bamboocell and bamboogrid reinforced clay bed was found to be 1.3 times that of reinforced with geocell and geogrid. The settlement of the clay bed was reduced by 97% due to the insertion of the combination of the bamboocell and bamboogrid as compared to the unreinforced clay bed. The bamboo was treated chemically to increase the durability. The performance of the bamboo was reduced by 15-20% after the chemical treatment; still the performance was better than its geosynthetic counterparts. Analytical studies revealed that the 3% of the ultimate tensile strength of the bamboogrid was mobilized while resisting the footing load. The study also explored the new and innovative applications of the geocells to protect underground utilities and buried pipelines. The laboratory model tests and the numerical studies were performed on small diameter PVC pipes, buried in geocell reinforced sand beds. In addition to geocells, the efficacy of only geogrid and geocell with additional basal geogrid cases were also studied. A PVC (Poly Vinyl Chloride) pipe with external diameter 75 mm and thickness 1.4 mm was used in the experiments. The vehicle tire contact pressure was simulated by applying the pressure on the top of the bed with the help of a steel plate. Results suggest that the use of geocells with additional basal geogrid considerably reduces the deformation of the pipe as compared to other types of reinforcements. Further, the depth of placement of pipe was also varied between 1B to 2B (B is the width of loading plate) below the plate in the presence of geocell with additional basal geogrid. More than 50% reduction in the pressure and more than 40% reduction in the strain values were observed in the presence of reinforcements at different depths as compared to the unreinforced beds. Further, experimental results were validated with 3-dimensional numerical studies using 3D FLAC. Good agreement in the measured pipe stain values were observed between the experimental and numerical studies. In addition, the results of the 1-g model tests were scaled up to the prototype case of the shallow buried pipeline below the pavement using the appropriate scaling laws. The efficacy of the geocells was also studied under the action of cyclic loading. The laboratory cyclic plate load tests were performed in soft clay bed by considering the three different cases, namely, unreinforced, geocell reinforced and geocell with additional basal geogrid reinforced. The coefficient of elastic uniform compression (Cu) was evaluated from the cyclic plate load tests for the different cases. The Cu value was found to increase in the presence of geocell reinforcement. The maximum increase in the Cu value was obtained for the case of the clay bed reinforced with the combination of geocell and the geogrid. The results of the laboratory model tests were extrapolated to prototype foundation supporting the low frequency reciprocating machine. The results revealed that, in the presence of the combination of geocell and the geogrid the natural frequency of the foundation-soil system increases by 4 times and the amplitude of the vibration reduces by 92%.