61 |
Shear design of reinforced high-strength concrete beamsCladera Bohigas, Antoni 07 March 2003 (has links)
Aunque el hormigón de alta resistencia se está utilizando de manera creciente en los últimos años para la construcción de estructuras, la norma Española vigente, la Instrucción EHE, sólo abarca hormigones de resistencias características a compresión inferiores a 50 MPa. El aumento de resistencia del hormigón está directamente asociado a una mejora en la mayoría de sus prestaciones, especialmente de la durabilidad, aunque también produce un aumento en la fragilidad y una disminución de la rugosidad de las fisuras, lo que afecta de forma muy especial a la resistencia a cortante.El objetivo principal de este trabajo es contribuir al avance del conocimiento del comportamiento frente a la rotura por cortante de vigas de hormigón de alta resistencia. Para ello, y en primer lugar, se ha llevado a cabo una extensa revisión del estado actual del conocimiento de la resistencia a cortante, tanto para hormigón convencional como para hormigón de alta resistencia, así como una profunda investigación de campañas experimentales anteriores. Se ha realizado una campaña experimental sobre vigas de hormigón de alta resistencia sometidas a flexión y cortante. La resistencia a compresión del hormigón de las vigas variaba entre 50 y 87 MPa. Las principales variables de diseño eran la cuantía de armadura longitudinal y transversal. Los resultados obtenidos experimentalmente han sido analizados para estudiar la influencia de las distintas variables en función de la resistencia a compresión del hormigón.Con el objetivo de tener en cuenta, no sólo los resultados de nuestros ensayos, sino también la gran cantidad de información disponible en la bibliografía técnica, se ha preparado una base de datos con vigas de hormigón convencional y de alta resistencia a partir del banco de datos de la Universidad de Illinois. Los resultados empíricos han sido comparados con los cortantes últimos calculados según la Instrucción EHE, las especificaciones AASHTO LRFD, el Código ACI 318-99 y el programa Response-2000, basado en la teoría modificada del campo de compresiones.Se han construido dos Redes Neuronales Artificiales (RNA) para predecir la resistencia a cortante en base a la gran cantidad de resultados experimentales. La principal característica de las RNA es su habilidad para aprender, mediante el ajuste de pesos internos, incluso cuando los datos de entrada y salida presentan un cierto nivel de ruido. Con los resultados de la RNA se ha realizado un análisis paramétrico de cada variable que afecta la resistencia última a cortante.Se han propuesto nuevas expresiones que tienen el cuenta el comportamiento observado para el diseño frente al esfuerzo cortante de vigas tanto de hormigón convencional como de alta resistencia con y sin armadura a cortante, así como una nueva ecuación para la determinación de la armadura mínima a cortante. Las nuevas expresiones presentan resultados que se ajustan mejor a los resultados experimentales que los obtenidos mediante la utilización de las normativas vigentes.Finalmente se han planteado varias sugerencias de futuras líneas de trabajo, que son resultado de la propia evolución del conocimiento sobre el tema de estudio durante el desarrollo de esta tesis. / Although High-Strength Concrete has been increasingly used in the construction industry during the last few years, current Spanish Structural Concrete code of practice (EHE) only covers concrete of strengths up to 50 MPa. An increase in the strength of concrete is directly associated with an improvement in most of its properties, in special the durability, but this also produces an increase in its brittleness and smoother crack surfaces which affects significantly the shear strength. The aim of this research is to enhance the understanding of the behaviour of high-strength concrete beams with and without web reinforcement failing in shear. In order to achieve this objective, an extensive review of the state-of-the-art in shear strength for both normal-strength and high-strength concrete beams was made, as well as in-depth research into previous experimental campaigns.An experimental programme involving the testing of eighteen high-strength beam specimens under a central point load was performed. The concrete compressive strength of the beams at the age of the tests ranged from 50 to 87 MPa. Primary design variables were the amount of shear and longitudinal reinforcement. The results obtained experimentally were analysed to study the influence of those parameters related to the concrete compressive strength.With the aim of taking into account, in addition to the results of our tests, the large amount of information available, a large database was assembled based on the University of Illinois Sheardatabank for normal-strength and high-strength concrete beams. These test results were compared with failure shear strengths predicted by the EHE Code, the 2002 Final Draft of EuroCode 2, the AASHTO LRFD Specifications, the ACI Code 318-99, and Response-2000 program, a computer program based on the modified compression field theory. Furthermore, two Artificial Neural Networks (ANN) were developed to predict the shear strength of reinforced beams based on the database beam specimens. An ANN is a computational tool made up of a number of simple, highly-interconnected processing elements that constitute a network. The main feature of an ANN is its ability to learn, by means of adjusting internal weights, even when the input and output data present a degree of noise. Based on the ANN results, a parametric study was carried out to study the influence of each parameter affecting the failure shear strength.New expressions are proposed, taking into account the observed behaviour for the design of high-strength and normal-strength reinforced concrete beams with and without web reinforcement. A new equation is given for the amount of minimum reinforcement as well. The new expressions correlate with the empirical tests better than any current code of practice.Finally, as a natural corollary to the evolution of our understanding of this field, some recommendations for future studies are made.
|
62 |
Zur Beurteilung der Festigkeitssteigerung von hochfestem Beton unter hohen Dehngeschwindigkeiten / The evaluation of the strength increase of high strength concrete at high rates of loadingOrtlepp, Sebastian 04 June 2007 (has links) (PDF)
Die vorliegende Arbeit zeigt Forschungsergebnisse zur Materialveränderung normaler und hochfester Betone unter Impulsbelastung gegenüber einer quasi-statischen Beanspruchung. Die Untersuchung wurde an speziellen eingeschnürten Prismen unter zentrischem Zug vorgenommen. Die Untersuchungen belaufen sich auf die generelle Festigkeitssteigerung und Modifikation der Spannungs-Dehnungs-Beziehung infolge veränderter Belastung. Neben den Betrachtungen des Materialverhaltens wurde auf die entstehenden Bruchflächen ein genaueres Augenmerk gerichtet, um Unterschiede des Materialverhaltens durch Änderungen beim Bruchvorgang zu erkennen. Zur Beurteilung der Bruchfläche werden die fraktale Analyse und ein Ortsfrequenzspektrum genutzt. / The present paper exhibits results of the latest research into the modification of the behaviour of normal and high-strength concrete on impact versus quasi-static loads. This examination has been carried out at tensile stress on special constricted specimens. The enquiries amount to the general strength increase and modification of the stress-strain-relationship due to a changing of load history. Further on, a special attention was turned to the crack surface to get differences of the material behaviour during the cracking process. The fractal analysis and a spatial frequency spectrum were used for the description of the surface.
|
63 |
Effect of constituent materials and curing methods on the abrasion resistance and durability of high performance concrete for pre-cast pre-stressed bridge deck slabs /Keshari, Shweta. January 1900 (has links)
Thesis (M.S.)--Oregon State University, 2010. / Printout. Includes bibliographical references (leaves 120-125). Also available on the World Wide Web.
|
64 |
Shear behaviour of continuous concrete beams reinforced with GFRP barsMahmoud, Karam Abdou Awad 26 November 2015 (has links)
Continuous beams represent main structural elements in most reinforced concrete (RC) structures such as parking garages and overpass bridges. Deterioration of such structures due to corrosion of steel reinforcement is common in North America. To overcome the corrosion problems, the use of fiber-reinforced polymer (FRP) bars and stirrups becomes a viable alternative to steel reinforcement. However, to date, the shear behaviour of FRP-RC continuous beams has not been explored yet. As such, the objective of this study is to investigate the shear behaviour of such beams.
In this study, twenty four full-scale continuous concrete beams were constructed and tested. The test beams had rectangular cross section with 200-mm width and a height of 300, 550 or 850 mm and were continuous over two equal spans. The main investigated parameters were concrete strength, type and ratio of longitudinal reinforcement, type and ratio of transverse reinforcement and beam effective depth. Moreover, a 3-D nonlinear finite element model (FEM) was constructed to simulate the behaviour of FRP-RC continuous beams. The model was verified against the experimental results and validated against test results from previous studies. Then, the verified/validated model was used to conduct a parametric study to investigate the effect of a wide range of the parameters on the shear behaviour of GFRP-RC beams.
The experimental and FEM results showed that shear-critical GFRP-RC continuous beams exhibited moment redistribution. Also, it was observed that increasing the concrete strength and the longitudinal reinforcement ratio increased the shear strength significantly. Moreover, the presence of GFRP stirrups significantly enhanced the shear strength of the tested beams. Regarding the size effect, test results showed that there was adverse or no size effect on the shear strength of GFRP-RC continuous beams when they failed in the interior shear span while beams failed in the exterior shear span exhibited clear size effect. Furthermore, a comparison between the test results and the provisions of the available models and FRP standards and design guidelines in North America revealed that these design provisions can be safely applied to continuous beams. / February 2016
|
65 |
Design and detailing of high strength reinforced concrete columns in Hong KongHo, Ching-ming, Johnny., 何正銘. January 2000 (has links)
published_or_final_version / Civil Engineering / Master / Master of Philosophy
|
66 |
Transfer and development length of 06-inch diameter prestressing strand in high strength lightweight concreteMeyer, Karl F. 05 1900 (has links)
No description available.
|
67 |
Multiscale modeling and design of ultra-high-performance concreteEllis, Brett D. 13 January 2014 (has links)
Ultra-High-Performance Concretes (UHPCs) are a promising class of cementitious materials possessing mechanical properties superior to those of Normal Strength Concretes (NSCs). However, UHPCs have been slow to transition from laboratory testing to insertion in new applications, partly due to an intuitive trial-and-error materials development process. This research seeks to addresses this problem by implementing a materials design process for the design of UHPC materials and structures subject to blast loads with specific impulses between 1.25- and 1.5-MPa-ms and impact loads resulting from the impact of a 0.50-caliber bullet travelling between 900 and 1,000 m/s. The implemented materials design process consists of simultaneous bottom-up deductive mappings and top-down inductive decision paths through a set of process-structure-property-performance (PSPP) relations identified for this purpose. The bottom-up deductive mappings are constructed from a combination of analytical models adopted from the literature and two hierarchical multiscale models developed to simulate the blast performance of a 1,626-mm tall by 864-mm wide UHPC panel and the impact performance of a 305-mm tall by 305-mm wide UHPC panel. Both multiscale models employ models at three length scales – single fiber, multiple fiber, and structural – to quantify deductive relations in terms of fiber pitch (6-36 mm/revolution), fiber volume fraction (0-2%), uniaxial tensile strength of matrix (5-12 MPa), quasi-static tensile strength of fiber-reinforced matrix (10-20 MPa), and dissipated energy density (20-100 kJ/m²). The inductive decision path is formulated within the Inductive Design Exploration Method (IDEM), which determines robust combinations of properties, structures, and processing steps that satisfy the performance requirements. Subsequently, the preferred material and structural designs are determined by rank order of results of objective functions, defined in terms of mass and costs of the UHPC panel.
|
68 |
Optimization of Span-to-depth Ratios in High-strength Concrete Girder BridgesPoon, Sandy Shuk-Yan 16 February 2010 (has links)
Span-to-depth ratio is an important bridge design parameter that affects structural behaviour, construction costs and aesthetics. A study of 86 constant-depth girders indicates that conventional ratios have not changed significantly since 1958. These conventional ratios are now questionable, because recently developed high-strength concrete has enhanced mechanical properties that allow for slenderer sections.
Based on material consumption, cost, and aesthetics comparisons, the thesis determines optimal ratios of an 8-span highway viaduct constructed with high-strength concrete. Three bridge types are investigated: cast-in-place on falsework box-girder and solid slabs, and precast segmental span-by-span box-girder. Results demonstrate that total construction cost is relatively insensitive to span-to-depth ratio over the following ranges of ratios: 10-35, 30-45, and 15-25 for the three bridge types respectively. This finding leads to greater freedom for aesthetic expressions because, compared to conventional values (i.e. 18-23, 22-39, and 16-19), higher ranges of ratios can now be selected without significant cost premiums.
|
69 |
Shear Resistance of High Strength Concrete I-beams with Large Shear Reinforcement RatiosXu, Roger Yuan 21 February 2012 (has links)
Experiments were performed to examine the shear resistance of heavily reinforced I-beams. Six I-beams with identical cross sections were constructed using high strength self-consolidating concrete, and were tested under monotonic anti-symmetric loading. All specimens had almost the same amount of longitudinal reinforcement, which provided sufficient flexural capacities. There were two variables: shear span and shear reinforcement ratio.
Test results showed that ACI code was too conservative in predicting the shear strengths of heavily shear reinforced I-beams, and the shear strength limit for deep beams should be increased to account for the benefit of high strength concrete. However, doubling the amount of stirrups did not improve the ultimate shear resistance much. The three beams that contained around 2.45% stirrups showed over-reinforced shear failures. Longitudinal flange cracking occurred to every specimen due to lack of cross tie reinforcement in the flanges, and it was believed to have reduced the ultimate shear strength.
|
70 |
Optimization of Span-to-depth Ratios in High-strength Concrete Girder BridgesPoon, Sandy Shuk-Yan 16 February 2010 (has links)
Span-to-depth ratio is an important bridge design parameter that affects structural behaviour, construction costs and aesthetics. A study of 86 constant-depth girders indicates that conventional ratios have not changed significantly since 1958. These conventional ratios are now questionable, because recently developed high-strength concrete has enhanced mechanical properties that allow for slenderer sections.
Based on material consumption, cost, and aesthetics comparisons, the thesis determines optimal ratios of an 8-span highway viaduct constructed with high-strength concrete. Three bridge types are investigated: cast-in-place on falsework box-girder and solid slabs, and precast segmental span-by-span box-girder. Results demonstrate that total construction cost is relatively insensitive to span-to-depth ratio over the following ranges of ratios: 10-35, 30-45, and 15-25 for the three bridge types respectively. This finding leads to greater freedom for aesthetic expressions because, compared to conventional values (i.e. 18-23, 22-39, and 16-19), higher ranges of ratios can now be selected without significant cost premiums.
|
Page generated in 0.0644 seconds