High strain rate plastic deformation of metals results in the formation of localized zones of severe shear strain known as adiabatic shear bands (ASBs), which are a precursor to shear failure. The formation of ASBs in a high-strength low alloy steel, namely AISI 4340, was examined based on prior heat treatments (using different austenization and tempering temperatures), testing temperatures, and impact strain rates in order to map out grain size and grain deformation behaviour during the formation of ASBs. In the current experimental investigation, ASB formation was shown to be a microstructural phenomenon which depends on microstructural properties such as grain size, shape, orientation, and distribution of phases and hard particles—all controlled by the heat treatment process. Each grain is unique and its material properties are heterogeneous (based on its size, shape, and the complexity of the microstructure within the grain). Using measurements of grain size at various heat treatments as well as dynamic stress-strain data, a finite element model was developed using Matlab and explicit dynamic software LSDYNA to simulate the microstructural deformation of grains during the formation of ASBs. The model simulates the geometrical grain microstructure of steel in 2D using the Voronoi Tessellation algorithm and takes into account grain size, shape, orientation, and microstructural material property inhomogeneity between the grains and grain boundaries. The model takes advantage of the Smooth Particle Hydrodynamics (SPH) meshless method to simulate highly localized deformation as well as the Johnson-Cook Plasticity material model for defining the behavior of the steel at various heat treatments under high strain rate deformation.The Grain Model provides a superior representation of the kinematics of ASB formation on the microstructural level, based on grain size, shape and orientation. It is able to simulate the microstructural mechanism of ASB formation and grain refinement in AISI 4340 steel, more accurately and realistically than traditional macroscopic models, for a wide range of heat treatment and testing conditions.

A aplicação de aços de alta resistência está fortemente difundida na indústria mecânica, principalmente em aplicações onde a redução de peso é importante, como por exemplo, a indústria de implementos rodoviários e maquinários agrícolas. Esta dissertação visa analisar a influência de diferentes aportes térmicos no comportamento microestrutural e mecânico de juntas soldadas através do processo MAG de modo a obter juntas com propriedades otimizadas. Para este estudo foram utilizadas chapas metálicas com espessura de 3 mm do aço de alta resistência e baixa liga USI LNE700. Os parâmetros nominais de energia de soldagem foram variados de acordo com os valores descritos pelo fornecedor SSAB. O processo de soldagem foi realizado com o auxílio de um sistema robotizado para manter a homogeneidade ao longo da junta, distância e posicionamento correto no comprimento total da junta soldada. Os ensaios para verificação do comportamento microestrutural e mecânico foram realizados com auxílio de microscopia ótica, perfis de microdureza e ensaios de tração. Buscaram-se utilizar aportes térmicos reduzidos para minimizar os efeitos de revenimento da martensita presente no metal de base, um dos principais responsáveis pela redução das propriedades mecânicas da junta soldada. Os resultados não mostraram significativa variações na microestrutura e propriedades de tração do material, porém o preenchimento da junta soldada formada apresenta um comportamento diretamente proporcional à energia de soldagem. / The application of high strength steels is strongly diffused in the engineering industry, especially in applications where weight reduction is important, such as the industry of agricultural machines and trailers industry. This investigation aims to analyze the influence of different heat inputs on microstructural and mechanical behavior of joint welded by GMAW in order to obtain joints with optimized properties. Sheet metal with a thickness of 3 mm high strength low alloy steel LNE700 (supplier Usiminas) were used. The welding energy was varied around the nominal value informed by the steel supplier SSAB for this study. The welding process was made using robotic system to maintain homogeneity along the joint, right distance and position during the total weld joint length. The microstructural and mechanical behaviors were performed with the optical microscope, microhardness profile and traction test. We attempted to use lower heat inputs to minimize the effects of tempering of martensite present in the base metal, a major contributor to the reduction of the mechanical properties of the welded joint. The results did not show significant microestructural and tensile properties variation, however, when the welding energy is increased, the welded joint penetration formed was increased as well.

A aplicação de aços de alta resistência está fortemente difundida na indústria mecânica, principalmente em aplicações onde a redução de peso é importante, como por exemplo, a indústria de implementos rodoviários e maquinários agrícolas. Esta dissertação visa analisar a influência de diferentes aportes térmicos no comportamento microestrutural e mecânico de juntas soldadas através do processo MAG de modo a obter juntas com propriedades otimizadas. Para este estudo foram utilizadas chapas metálicas com espessura de 3 mm do aço de alta resistência e baixa liga USI LNE700. Os parâmetros nominais de energia de soldagem foram variados de acordo com os valores descritos pelo fornecedor SSAB. O processo de soldagem foi realizado com o auxílio de um sistema robotizado para manter a homogeneidade ao longo da junta, distância e posicionamento correto no comprimento total da junta soldada. Os ensaios para verificação do comportamento microestrutural e mecânico foram realizados com auxílio de microscopia ótica, perfis de microdureza e ensaios de tração. Buscaram-se utilizar aportes térmicos reduzidos para minimizar os efeitos de revenimento da martensita presente no metal de base, um dos principais responsáveis pela redução das propriedades mecânicas da junta soldada. Os resultados não mostraram significativa variações na microestrutura e propriedades de tração do material, porém o preenchimento da junta soldada formada apresenta um comportamento diretamente proporcional à energia de soldagem. / The application of high strength steels is strongly diffused in the engineering industry, especially in applications where weight reduction is important, such as the industry of agricultural machines and trailers industry. This investigation aims to analyze the influence of different heat inputs on microstructural and mechanical behavior of joint welded by GMAW in order to obtain joints with optimized properties. Sheet metal with a thickness of 3 mm high strength low alloy steel LNE700 (supplier Usiminas) were used. The welding energy was varied around the nominal value informed by the steel supplier SSAB for this study. The welding process was made using robotic system to maintain homogeneity along the joint, right distance and position during the total weld joint length. The microstructural and mechanical behaviors were performed with the optical microscope, microhardness profile and traction test. We attempted to use lower heat inputs to minimize the effects of tempering of martensite present in the base metal, a major contributor to the reduction of the mechanical properties of the welded joint. The results did not show significant microestructural and tensile properties variation, however, when the welding energy is increased, the welded joint penetration formed was increased as well.

Next generation defense and commercial applications for structural steels require new alloys that eliminate or reduce critical elements from their composition to lower cost and improve manufacturability, while maintaining or exceeding high strength and toughness requirements. A new alloy, denoted as AF9628, has recently been developed for this purpose and its manufacturing characteristics and the material response in component manufacturing must be fully understood. In the present study, hardened AF9628 alloy was turned with a coated carbide cutting tool under fixed cutting speed, feed rate, and depth of cut parameters. This work focuses on chip-form and tool-wear analysis to understand, for the first time with AF9628, these fundamental aspects of the turning process and their relationship to productivity and part quality. Current industry standard practice of flood-cooled machining for AF9628 was used during machining experiments. Dry, minimum quantity lubrication (MQL), and cryogenic machining were investigated as alternative cooling and lubrication conditions. High-speed imaging during AF9628 turning experiments provides a new insight into the chip formation process, while the use of optical microscopy and scanning white light interferometry allowed for further characterization of chip-form and tool-wear. Chip-form is favorable as short, arc-shaped chips with new tools under all of the tested cooling and lubrication conditions. As a result of rapid wear at the end of the tool-life in all of the experimental conditions, chip-form evolves to unfavorably long, snarled ribbon-like chips and the resultant cutting force increased by as much as 64% under flood-cooled conditions. Tool-wear types that were observed during experiments include a combination of nose wear, built-up edge, plastic deformation, and groove wear on the rake face. Due to the fixed cutting parameters and cutting tool selected for this study, which were designed for flood-cooled machining in a prior study, undesirable failure of the cutting tools under dry, MQL, and cryogenic machining occurred. Future work requires experimentation across a wider processing space, and with different cutting tools, to thoroughly evaluate alternative cooling and lubrication techniques for machining AF9628.

No presente trabalho estudou-se a recristalização do aço de alta resistência baixa liga (ARBL) microligado ao nióbio (160 ppm em peso) da Companhia Siderúrgica Nacional 2336 utilizado na fabricação de reforços estruturais para a indústria automobilística. A grande utilização deste tipo de aço pelas indústrias tem motivado o desenvolvimento de novas ligas capazes de atender a requisitos críticos de estampagem combinado com alta resistência mecânica. Amostras deste aço no estado laminado a quente foram deformadas posteriormente a frio em escala piloto com reduções de 50 e 70%, reduções típicas na indústria, e recozidas em banho de sal em temperaturas variando entre 600 e 700ºC em diferentes tempos. A evolução microestrutural das amostras no estado encruado e na condição recozida foi acompanhada utilizando-se as técnicas de microscopia ótica e eletrônica de varredura. As texturas de deformação e de recristalização foram determinadas via difração de raios X. A fração volumétrica recristalizada (Xv) e o tamanho de grão foram determinados com o auxílio de metalografia quantitativa nas amostras recozidas. Medidas de microdureza Vickers foram utilizadas para construir as curvas de encruamento e da cinética de amolecimento em função da temperatura de recozimento e comparadas com curvas construídas pelo primeiro método. Os resultados mostram que a recristalização ocorre em temperaturas acima de 650°C. Com auxílio de um gráfico de Xv contra A (fração amolecida), podemos observar a ocorrência de um desvio da idealidade a 650°C e 700°C. A explicação mais provável é a ocorrência de precipitação, especialmente para o aço menos deformado. Os valores do expoente de Avrami obtidos a partir das duas abordagens (medidas de microdureza e metalografia quantitativa) são apresentados e discutidos. / The recrystallization of a high strength low alloy steel (HSLA) containing niobium (160 wt-ppm) was investigated. The HSLA steel, named CSN 2336, is used in the manufacture of structural parts for automotive industry. The increasing use of this application type of steels in automotive industries has motivated the development of new alloys able to gather the critical requirements for deep drawing combined with high strengths. Samples of this steel in hot-rolled condition were cold-rolled with reductions of 50% and 70%, commonly used in most of applications, and isothermally annealed in salt bath at temperatures between 600 and 700ºC. The microstructure of the samples in both coldworked and annealed states was imaged using light optical (LOM) and scanning electronic microscopies (SEM). Deformation and recrystallization textures were determined by X-ray diffraction. The recrystallized volume fraction (Xv) and the mean grain size were determined by quantitative metallography in the annealed samples. Vickers microhardness testing was used to determine the work hardening and the softening kinetics behaviors. The results show that recrystallization occurs at temperatures above 650°C for the most deformed steel. By plotting Xv against A (softening fraction), we observe the occurrence of a deviation from ideality at 650°C and 700°C, likely caused by solid-state precipitation, especially for the less deformed steel. The values of n (Avrami exponent) obtained from both approaches (softening curves and quantitative metallography) are presented and discussed.

No presente trabalho estudou-se a recristalização do aço de alta resistência baixa liga (ARBL) microligado ao nióbio (160 ppm em peso) da Companhia Siderúrgica Nacional 2336 utilizado na fabricação de reforços estruturais para a indústria automobilística. A grande utilização deste tipo de aço pelas indústrias tem motivado o desenvolvimento de novas ligas capazes de atender a requisitos críticos de estampagem combinado com alta resistência mecânica. Amostras deste aço no estado laminado a quente foram deformadas posteriormente a frio em escala piloto com reduções de 50 e 70%, reduções típicas na indústria, e recozidas em banho de sal em temperaturas variando entre 600 e 700ºC em diferentes tempos. A evolução microestrutural das amostras no estado encruado e na condição recozida foi acompanhada utilizando-se as técnicas de microscopia ótica e eletrônica de varredura. As texturas de deformação e de recristalização foram determinadas via difração de raios X. A fração volumétrica recristalizada (Xv) e o tamanho de grão foram determinados com o auxílio de metalografia quantitativa nas amostras recozidas. Medidas de microdureza Vickers foram utilizadas para construir as curvas de encruamento e da cinética de amolecimento em função da temperatura de recozimento e comparadas com curvas construídas pelo primeiro método. Os resultados mostram que a recristalização ocorre em temperaturas acima de 650°C. Com auxílio de um gráfico de Xv contra A (fração amolecida), podemos observar a ocorrência de um desvio da idealidade a 650°C e 700°C. A explicação mais provável é a ocorrência de precipitação, especialmente para o aço menos deformado. Os valores do expoente de Avrami obtidos a partir das duas abordagens (medidas de microdureza e metalografia quantitativa) são apresentados e discutidos. / The recrystallization of a high strength low alloy steel (HSLA) containing niobium (160 wt-ppm) was investigated. The HSLA steel, named CSN 2336, is used in the manufacture of structural parts for automotive industry. The increasing use of this application type of steels in automotive industries has motivated the development of new alloys able to gather the critical requirements for deep drawing combined with high strengths. Samples of this steel in hot-rolled condition were cold-rolled with reductions of 50% and 70%, commonly used in most of applications, and isothermally annealed in salt bath at temperatures between 600 and 700ºC. The microstructure of the samples in both coldworked and annealed states was imaged using light optical (LOM) and scanning electronic microscopies (SEM). Deformation and recrystallization textures were determined by X-ray diffraction. The recrystallized volume fraction (Xv) and the mean grain size were determined by quantitative metallography in the annealed samples. Vickers microhardness testing was used to determine the work hardening and the softening kinetics behaviors. The results show that recrystallization occurs at temperatures above 650°C for the most deformed steel. By plotting Xv against A (softening fraction), we observe the occurrence of a deviation from ideality at 650°C and 700°C, likely caused by solid-state precipitation, especially for the less deformed steel. The values of n (Avrami exponent) obtained from both approaches (softening curves and quantitative metallography) are presented and discussed.

O presente trabalho avalia e compara os resultados da tenacidade à fratura da zona termicamente afetada (ZTA) de soldas múltiplos passes por meio de ensaios de CTOD. Para este estudo, foi utilizado um aço alta resistência e baixa liga (ARBL) resistente à corrosão ambiental. As soldas foram realizadas com insumo de calor de 30 e 50 kJ/cm em um chanfro 1/2 K. Os resultados dos ensaios de CTOD mostraram que a solda produzida com maior insumo de calor apresenta tenacidade à fratura mais elevada. A análise microestrutural revelou que as microestruturas de elevada dureza e baixa tenacidade, formadas na ZTA de granulação grosseira, para a condição de 30 kJ/cm, deram lugar às microestruturas de tenacidade mais elevada, para o insumo de calor de 50 kJ/cm. / In this work the fracture toughness results of the heat affected zone (HAZ) in a multiple pass welds using a crack tip opening displacement (CTOD) concept were evaluated and compared. It was used an ambiental resistent high strengh low alloy steel. The welds were carried out using a heat input of 30 and 50 kJ/cm in a bevel preparation 1/2 K. The results of CTOD testing showed that increasing heat input, caused an improvement in the weldments fracture toughness. Microstructural analysis revealed that the high hardness and low toughness microstructures formed at coarse grain HAZ, near fusion line, for welding condition 30 kJ/cm were changed to higher toughness microstructure using a heat input of 50 kJ/cm.

O presente trabalho avalia e compara os resultados da tenacidade à fratura da zona termicamente afetada (ZTA) de soldas múltiplos passes por meio de ensaios de CTOD. Para este estudo, foi utilizado um aço alta resistência e baixa liga (ARBL) resistente à corrosão ambiental. As soldas foram realizadas com insumo de calor de 30 e 50 kJ/cm em um chanfro 1/2 K. Os resultados dos ensaios de CTOD mostraram que a solda produzida com maior insumo de calor apresenta tenacidade à fratura mais elevada. A análise microestrutural revelou que as microestruturas de elevada dureza e baixa tenacidade, formadas na ZTA de granulação grosseira, para a condição de 30 kJ/cm, deram lugar às microestruturas de tenacidade mais elevada, para o insumo de calor de 50 kJ/cm. / In this work the fracture toughness results of the heat affected zone (HAZ) in a multiple pass welds using a crack tip opening displacement (CTOD) concept were evaluated and compared. It was used an ambiental resistent high strengh low alloy steel. The welds were carried out using a heat input of 30 and 50 kJ/cm in a bevel preparation 1/2 K. The results of CTOD testing showed that increasing heat input, caused an improvement in the weldments fracture toughness. Microstructural analysis revealed that the high hardness and low toughness microstructures formed at coarse grain HAZ, near fusion line, for welding condition 30 kJ/cm were changed to higher toughness microstructure using a heat input of 50 kJ/cm.

The present study focuses on developing a relationship between process variables, mechanical properties and post weld microstructure in Friction Stir Welded HSLA 65 steel. Fully consolidated welds can be produced in HSLA 65 steel by PCBN Convex-Scrolled-Shoulder-Step-Spiral (CS4) tool over a wide range of parameters. Microstructures in the nugget center (NC) are dominated by lath bainite and a few polygonal/allotriomorphic grain boundary ferrites. FSW dependent variables are related to FSW independent variables by non-linear relationship. Heat input is identified to be the best parameter index to correlate with microstructures. With increasing heat input, the volume of bainite is reduced, the shape of bainite is more curved and grain/lath size become coarser. A linear relationship was established between heat input and semi-quantitative post-weld microstructures based on the optical microstructures. Further analysis has been applied on the NC to obtain more fundamental understanding of FSW. The new approach via Orientation Imaging Microscopy (OIM) was developed to acquire quantitative microstructural data including bainite lath/packet and prior austenite grain size (PAG). A linear relationship between heat input and quantitative microstructural features in the NC have been established. Mechanical properties exhibits linear relationship with heat input. These correlations can be utilized to determine FSW weld parameter to get desired mechanical properties welds.

Este trabalho tem por objetivo caracterizar e comparar as microestruturas de diferentes regiões de uma chapa de aço microligado para tubo API 5L X65, empregado no transporte de gás natural e petróleo, como recebido e submetido a tratamentos térmicos de austenitização e resfriamento contínuo sob diferentes taxas de resfriamento. O aço em estudo apresenta uma linha de segregação central, originada durante o processo de produção do aço. Corpos de prova de dilatometria foram usinados da região central e de outras regiões da chapa. As amostras foram previamente austenitizadas a 1200°C e temperadas em água, visando solubilizar grande parte dos precipitados presentes no aço. Após este tratamento, as amostras foram austenitizadas em um dilatômetro de têmpera a 950°C por 180s, e em seguida resfriadas nas seguintes taxas de resfriamento: 0,5°C/s, 1°C/s, 5°C/s, 10°C/s, 20°C/s, 30°C/s, 40°C/s, 50ºC/s e 60ºC/s. Valores de temperatura e tempo correspondentes a inflexões da curva dilatométrica foram obtidas e correlacionadas com a microestrutura, para cada taxa de resfriamento. Com base nesta análise foi traçado um diagrama de Transformação por Resfriamento Contínuo (TRC) do material. / This work aims to characterize and compare the microstructures of different regions of a plate of microalloyed pipeline steel that conforms to API 5L X65, employed in the transportation of natural gas and oil, as received and after being subjected to heat treatments of austenitization and continuous cooling under different cooling rates. The steel under study presents a central line of segregation that was originated during production. Specimens for dilatometry were machined from the central region and from different regions of the plate. The samples were austenitized at 1200°C and in quenched in water, with the purpose of solubilizing most of the precipitates in the steel. After the preliminary heat treatment, the specimens were austenitized at 950°C for 180s and cooled under the cooling rates: 0.5°C/s, 1°C/s, 5°C/s, 10°C/s, 20°C/s, 30°C/s, 40°C/s, 50ºC/s and 60ºC/s in a quench dilatometer. Values of temperature and time correspond of transformation for each rate of cooling were used for the determination of the Continuous Cooling Transformation (CCT) diagram.