No description available.

The drainage behaviour of sports pitches is not well understood nor has performance been measured in the past. Within planning authorities there is a perceived contribution of pitch water discharge to local flood risk; whereby all the rainfall surface runoff is rapidly channelled through the drainage system to the pitch outfall. However, empirical evidence from industry suggested that this may not be a realistic assumption from observations of low drainage volumes yielded from pitch drainage systems. Furthermore, discharge constraints imposed have in many cases resulted in grossly over-designed off-line drainage attenuation systems for new sports developments through lack of understanding. In contrast, sports pitches indeed have the potential to enhance the attenuation performance of the subsoils and provide localised effective management of surface water runoff, and a significant storage volume if designed appropriately The findings in this thesis confirm that pitch bases demonstrate the key functions that are in fact reflected in the design requirements of Sustainable Urban Drainage Systems (SuDS). This PhD research project was conducted to investigate and document the performance of common pitch construction and drainage systems to better characterise the key drainage mechanisms that occur and control the flow of surface rain water through the pitch to the discharge outfall. The project developed a triangulated approach to the investigations, comprising: field measurements of climate and discharge behaviour at a range of artificial and natural turf pitches in England; laboratory physical model testing of pitch component hydraulics; and predictive mathematical modelling of how a pitch system may be expected to perform hydraulically based on key material and system drainage principles. The field monitoring systems were developed as part of the research, as was bespoke laboratory physical simulation of a pitch construction. It was found that very variable yields (% out versus % in) of water were detected from the monitored field sites. The values varied across a range of < 1 to 88%, with the natural turf providing higher yields in general. The antecedent weather patterns did not show a clear relationship with yield as might have been expected. However, it was not always possible to retrieve detailed information on the subsoil conditions or hydraulic capability reducing the conclusiveness of the discharge flow measurements. The scaled laboratory testing of pitch materials established the importance and magnitude of barriers to percolation of surface water through the layers of the pitch constructions, in particular artificial pitch profiles. It was found that a significant proportion of the total rainfall head was required to instigate percolation of surface water through the carpet and into the pitch i.e. breakthrough head. In addition, several constituent pitch materials exhibited water retention characteristics that reduced that rate of free percolation of surface water through the pitch profile. The net impact is to reduce the net available head of water to further drive flow through the layers to the pipe network drainage system. A conceptual hydraulic model, developed from the literature, was further developed into a simple numerical model. The model was informed by parameters determined from the laboratory measurements and key groundwater drainage flow theory to attempt to replicate a pitch drainage system. It was envisaged that the models would be validated by the field data, although this proved challenging as a result of the field data variability and the multivariate nature of the influences on flows measured. A key finding of the modelling was further establishing the likely head of water generated at the interfaces between the bottom of the granular sub-base and the pipe collection drainage system beneath. This resulted in limited pipe infiltration and low total flows to the outfall, further corroborating the project field results and the anecdotal observations from practitioners. The combined unique data sets provide a refined model for sports pitch drainage to both reinforce understanding and inform practical design and operation.

yes / A comprehensive experimental programme was performed with the focus on assessing the effects of compaction delay and ambient temperature on the physical, mechanical and hydraulic properties of lime treated expansive clays. Specimens were mellowed for a period of 0, 3, 6, 12, 24 and 48 h at two different temperatures of 20°C and 40°C prior to being compacted, tested and/or cured for up to 28 days for evaluating the impacts on long-term strength development. All specimens were prepared with the same dry unit weight of 12.16 kN/m3 and moisture content of 40% except for tests aimed at determining dry unit weight as a function of mellowing period. The results revealed that as the mellowing duration increased the dry unit weight declined remarkably at both temperature within the first 12 h. In addition, higher reduction rate was observed when specimens were mel-lowed at a temperature of 40°C. A 97% reduction in swelling pressure was obtained when the specimens were compacted upon mixing (zero hour mellowing period) and left to cure for 24 h prior to testing. Permeability coefficient of lime treated expansive clays was increased by up to 40 times when compaction was delayed for 24 h or when specimens were mellowed at 40°C. Specimens mellowed at a temperature of 40°C showed rela-tively stable values of permeability coefficient over the measurement period which could be attributable to accelerated pozzolanic reaction. The Unconfined Compressive Strength tests revealed that strength of lime treated expansive clays is significantly affected by compaction delay. An increase of 234% and 282% in the Unconfined Compressive Strength was achieved after 24 h of mixing with no compaction delay at 20°C and 40°C respectively. Gradual long-term gain in strength was observable within the 28 days post mixing but the rate of strength gain becomes slower and independent of temperature after the first 24 h of mixing. The results sug-gested that the four key reaction mechanisms occur concurrently with the first 12–24 h after lime addition recognized as being the most crucial period of time. Damaging the cementitious compounds by delayed com-paction is harmful to strength and restraining of swelling potential of lime treated expansive clays.

Yes / This paper focuses on monitoring the evolution of lime-clay reactions using geotechnical parameters as a function of lime content and environmental temperature. Lime contents of 5, 7, 9, 11 and 13% by dry weight of expansive clay powder were added to prepare lime-clay specimens. The specimens were prepared at the same dry unit weight of 12.16 kN/m3 and moisture content of 40% except for tests aimed at the determination of dry unit weight as a function of mellowing period. Prepared specimens were mellowed or cured at two different ambient temperatures of 20 °C and 40 °C. Results attained from Unconfined Compressive Strength and permeability tests were employed to assess the impact of lime content on the mechanical and hydraulic properties of lime treated expansive clays. The results revealed that at the beginning, the rate of strength gain is remarkably fast for a particular period of time which is dependent on lime content. Furthermore, the strength gain on specimens cured at 40 °C is 8 times higher than that observed on specimens cured at 20 °C which highlights significant effect for the environmental temperature on accelerating the chemical reactions. Reduced dry unit weight due to increased resistance to compactability is observable with increasing lime content and higher environmental temperature. Accelerated pozzolanic reaction at higher environmental temperature resulted in permeability coefficient of specimens mellowed for 24 h at 40 °C to be higher than those mellowed at 20 °C. The results also highlighted that the permeability coefficient would be relatively stable when expansive clays were treated with small amounts of lime e.g. 5%.

Expansive clays used in engineering practice are usually unsaturated and are sensitive to chemical composition of the in-pore solution. To analyse the complex coupled problems involved, an efficient mathematical model which can account for these chemo-hydro-mechanical behaviours has been developed. In this thesis, expansive clays are conceptualised into three-phase multi-species porous media. Based on the modified mixture theory and irreversible thermodynamics, a thermo-electro-chemo-hydro-mechanical framework has been developed. The Clausius-Duhem inequality, which governs the dissipations associated with mechanical work, phase transformation, mass transport and thermal transport, is rigorously derived. Based on this thermodynamic framework, constitutive laws for bulk liquid and salt mass transport, free and adsorbed water inter-phase mass transfer, and the chemo-elastic-plastic deformations of soil skeleton have been developed. The model has been implemented into the FEM software Bil and validated by simulating available experimental data on Boom Clays. What’s more, the salt infiltration process into an unsaturated expansive clay layer has been simulated to illustrate the applicability of the model. / Argiles gonflantes utilisées dans la pratique de l'ingénierie sont généralement insaturés et sont sensibles à la composition chimique de la solution dans les pores. Pour analyser les problèmes complexes couplés impliqués, un modèle mathématique efficace qui peut expliquer ces comportements chimio-hydro-mécanique a été développé. Dans cette thèse, argiles gonflantes sont conceptualisés dans triphasés multi-espèces de milieux poreux. Sur la base de la théorie de mélange modifié et thermodynamique irréversible, un cadre thermo-électro-chimio-hydro-mécanique a été développé. L'inégalité de Clausius-Duhem, qui régit les dissipations associés au travail mécanique, transformation de phase, le transport de masse et le transport thermique, est rigoureusement dérivée. Basé sur ce cadre thermodynamique, lois de comportement pour liquides en vrac et le sel de transport de masse, transfert de masse de l'eau entre en phase libre et adsorbé, et les déformations chimio-élastique-plastique de squelette du sol ont été développés. Le modèle a été mis en œuvre dans le logiciel FÉM Bil et validé en simulant les données expérimentales disponibles sur les argiles de Boom. Qui plus est, le processus d'infiltration de sel dans une couche d'argile gonflante insaturés a été simulée pour illustrer l'applicabilité du modèle.

Les boucles diphasiques à pompage thermo-capillaire de type LHP (pour Loop Heat Pipe, en anglais), dont le fonctionnement s’apparente à celui d’un caloduc, permettent un transfert de chaleur particulièrement efficace et entièrement passif entre une source chaude et une source froide. Ce transfert s’effectue au moyen d’un fluide diphasique, mû grâce à la force motrice capillaire générée par un matériau poreux contenu dans l’évaporateur/réservoir de la LHP. Outre son rôle de barrière hydraulique entre les phases liquide et vapeur, ce matériau doit assurer une fonction de barrière thermique afin de favoriser l’évaporation du liquide. L’aptitude du matériau à remplir ses fonctions dépend étroitement de sa microstructure, elle-même liée à la méthode de fabrication. Dès lors, l’objectif de la thèse est d’associer la science des matériaux à celle de la thermique, pour améliorer les procédures de fabrication de structures capillaires existantes ou tester de nouvelles méthodes, et aboutir à des structures dont les caractéristiques sont en adéquation avec celles qui sont recherchées. / The capillary pumped loops (CPL) or loop heat pipes (LHP), whom the operating principle is similar to classic heat pipes, enable an efficient heat transfer between a hot source and a cold source without additional energy sources. Indeed, a porous structure provides a capillary force that enables a two-phase fluid to circulate around the loop, transferring the heat from the evaporator to the condenser. The porous structure acts as a hydraulic barrier between the two phases and as a thermal barrier enabling the liquid evaporation. The ability of the capillary structure to fulfil its mission depends on its microstructure, and thus on the manufacturing process. Therefore, the objective of the present thesis is to join the thermal sciences with the material sciences in order to improve the existing manufacturing procedure or even to test new ones. It aims at obtaining capillary structures corresponding to heat transfer applications.