1 |
Multi-Scale Indentation Hardness Testing; A Correlation and ModelBennett, Damon W. 20 January 2010 (has links)
This thesis presents the research results of a correlation and model based on nano
and macroindentation hardness measurements. The materials used to develop and test
the correlation include bulk tantalum and O1 tool steel. Following the literature review
and a detailed description of the experimental techniques, the results of the
nanoindentation hardness measurements are presented. After applying the methods and
correlation recommended here, the results should give an accurate value of hardness in
the Vickers scale for microstructural features that are too small to be precisely and
exclusively measured using the traditional macroindentation hardness technique. The
phenomena and influential factors in nanoindentation hardness testing are also discussed.
These phenomena and theories are consistent with the microstructural behavior predicted
in the Nix and Gao model for mechanism-based strain gradients. Implementing the
correlation factors and/or correlation curve, accurate results can be found for metals over
a broad hardness range. Initially, this research may impact the pipeline division of the
petroleum industry by providing a correlation to the Vickers scale for nanoindentation testing of microstructural features. This thesis may also provide a research methodology
to develop hardness correlations for materials other than metals.
This thesis consists of eight chapters. Following an introduction in Chapter I, the
research motivations and objectives are highlighted in Chapter II. Chapter III explains
the multi-scale indentation techniques used in this thesis and Chapter IV presents the
materials preparation techniques used. Then, the results are presented in Chapter V,
followed by the factors affecting nanoindentation hardness in Chapter VI. Finally,
Chapters VII and VIII reveal the indentation contact analysis, correlation, and
conclusions of this research, respectively.
|
2 |
Investigation of the effect of process parameters on the formation of recast layer in wire-EDM of Inconel 718Newton, Thomas Russell 15 February 2008 (has links)
Inconel 718 is a high nickel content superalloy possessing high strength at elevated temperatures and resistance to oxidation and corrosion. The non-traditional manufacturing process of wire-electrical discharge machining (EDM) possesses many advantages over traditional machining during the manufacture of Inconel 718 parts. However, certain detrimental effects are also present. The top layer of the machined surface is melted and resolidified to form what is known as the recast layer. This layer demonstrates microstructural differences from the bulk workpiece, resulting in altered material properties.
An experimental investigation was conducted to determine the main machining parameters which contribute to recast layer formation in wire-EDM of Inconel 718. It was found that average recast layer thickness increased with energy per spark, peak discharge current, current pulse duration, and open-voltage time and decreased with sparking frequency and table feed rate. Over the range of parameters tested, the recast layer was observed to be between 5 and 10 μm in average thickness, although highly variable in nature.
Surface roughness of the cut parts showed an increase with energy per spark. Electron Probe Microanalysis (EPMA) revealed the recast layer to be alloyed with elements from the wire electrode. X-ray diffraction testing showed the residual tensile stresses evident near the cut surface to decrease with energy per spark. Additionally, nano-indentation hardness testing indicated that the recast layer is reduced in hardness and elastic modulus compared to the bulk material. Vibratory tumbling was found to be a moderately effective post-processing tool for recast layer removal when using pre-formed ceramic abrasive media or fine grained aluminum oxide.
|
3 |
Plastic Deformation During Indentation Of Crystalline And Amorphous MaterialsPrasad, Korimilli Eswara 11 1900 (has links) (PDF)
Indentation hardness, H, has been widely used to characterize the mechanical properties of materials for more than a century because of the following advantages of this technique; (1) it requires small sample and (2) the test is non destructive in nature. Recent technological advances helped in the development of instrumented indentation machines which can record the load, P, vs. displacement, h, data continuously during indentation with excellent load and displacement resolutions. From these, H and the elastic modulus, E, of the indented material can be obtained on the basis of the ‘contact area’ of the indentation at the maximum load. The estimation of true contact area becomes difficult during ‘pile-up’ and ‘sink-in’, commonly observed phenomena while indentation of a low and high strain hardened materials. In order for the better understanding of these phenomena it is important to understand the plastic flow distribution under indenters. It is also important for the prediction of elastic-plastic properties from the P-h data. Recently, there have been considerable theoretical and simulation efforts on this front with a combination of dimensional analysis and finite element simulations. One of the important input parameter for the dimensional analysis is the ‘representative strain’ under the indenter, which is a strong function of the indenter geometry. However there is no comprehensive understanding of the representative strain under the indenter despite several studies till date. One objective of the present thesis is to conduct an experimental analysis of the plastic flow during the sharp indentation.
The plastic zone size and shape under conical indenters of different apex angles in a pure and annealed copper were examined by employing the subsurface indentation technique to generate the hardness map. From these isostrain contours are constructed joining the data having similar strain values. The following are the key observations. (1) The plastic strain contours are elliptical in nature, spreading more along the direction of the indenter axis than the lateral direction. (2) The magnitude of the plastic strain in the contact region decreases with increasing the indenter angle. (3) The strain decay in the indentation direction follow a power-law relation with the distance. The estimated representative strains under the indenters, computed as the volume average strain within the elastic-plastic boundary, decreases with increasing indenter angle. We also performed finite element simulations to generate plastic flow distribution under the indenter geometries and compared with the experimental results. The results suggest that the experimental and computed average strains match well. However, the plastic strain contours do not, suggesting that further detailed understanding of the elasto-plastic deformation underneath the sharp indenter is essential before reliable estimates of plastic properties from the P-h curves can be made routinely.
The second objective of this thesis is to understand plastic flow in amorphous alloys. It is now well established that plastic deformation in metallic glasses is pressure sensitive, owing to the fundamentally different mechanisms vis-à-vis the dislocation mediated plastic flow in crystalline metals alloys. Early work has shown that the pressure sensitivity of amorphous alloys gets reflected as high constraint factor, C (hardness to yield stress ratio), which sometimes exceed 3.0. In this thesis, we study the temperature dependence of pressure sensitive plastic flow in bulk metallic glasses (BMGs) using C as the proxy for the pressure sensitivity. Experiments on three different BMGs show that C increases with temperature hence the pressure sensitivity. In addition we have carried out finite element simulations to generate P-h curves for different levels of pressure sensitivities and match them with the experimental curves that are obtained at different temperatures. Simulations predict that higher pressure sensitivity index values are required to match the experimental curves at high temperatures confirming that the pressure sensitivity increases with increasing temperature. The fundamental mechanisms responsible for the increase in pressure sensitivity are discussed in detail. Finally we pose a question, is the increase in pressure sensitivity with temperature is common to other amorphous materials such as strong amorphous polymers? In order to answer this question we have chosen PMMA, a strong amorphous polymer. In this study also we have taken C as a proxy to index the pressure sensitivity. Indentation stress-strain curves are constructed at different temperature using spherical indentation experiments. The C values corresponding to different temperatures are determined and plotted as a function of temperature. It is found that C increases with temperature implying that the pressure sensitivity of amorphous polymers also increases with temperature. The micro-mechanisms responsible for the increase in pressure sensitivity are sought.
|
Page generated in 0.4123 seconds