Cycling of the relative humidity (RH) levels in the reactant streams of polymer electrolyte membrane (PEM) fuel cells has been reported to decay fuel cell performance. This study focuses on the accelerated durability testing to examine different modes of membrane failure via RH cycling. A single PEM fuel cell with an active area of 42.25 cm2 was tested. A Greenlight G50 test station was used to establish baseline cell (Run 1) performance with 840 hours of degradation under high-humidity idle conditions at a constant current density of 10 mA cm-2. Under the same conditions, two other experiments were conducted by varying the RH. For the H2-air RH cycling test (Run 2), anode and cathode inlet gases were provided as dry and humidified gases. Another RH cycling experiment was the H2 RH cycling test (Run 3): the anode inlet gas was cycled whereas keeping the other side constantly at full humidification. These two RH cycling experiments were alternated in dry and 100% humidified conditions every 10 and 40 minutes, respectively. In the experiments, the fuel cells contained a GoreTM 57 catalyst coated membrane (CCM) and 35 BC SGL gas diffusion layers (GDLs). The fuel cell test station had been performed under idle conditions at a constant current density of 10 mA cm-2. Under the idle conditions, operating at very low current density, a low chemical degradation rate and minimal electrical load stress were anticipated. However, the membrane was expected to degrade due to additional stress from the membrane swelling/contraction cycle controlled by the RH. In this work the performance of the 100% RH humidified cell (Run 1) was compared with that of RH cycling cells (Run 2 and Run 3). Chemical and mechanical degradation of the membrane were investigated using in-situ and ex-situ diagnostic methods. The results of each measurement during and after fuel cell operation are consistent. They clearly show that changing in RH lead to an overall PEM fuel cell degradation due to the increase in membrane degradation rate from membrane resistance, fluoride ion release concentration, hydrogen crossover current, membrane thinning, and hot-spot/pin-hole formation.

Cycling of the relative humidity (RH) levels in the reactant streams of polymer electrolyte membrane (PEM) fuel cells has been reported to decay fuel cell performance. This study focuses on the accelerated durability testing to examine different modes of membrane failure via RH cycling. A single PEM fuel cell with an active area of 42.25 cm2 was tested. A Greenlight G50 test station was used to establish baseline cell (Run 1) performance with 840 hours of degradation under high-humidity idle conditions at a constant current density of 10 mA cm-2. Under the same conditions, two other experiments were conducted by varying the RH. For the H2-air RH cycling test (Run 2), anode and cathode inlet gases were provided as dry and humidified gases. Another RH cycling experiment was the H2 RH cycling test (Run 3): the anode inlet gas was cycled whereas keeping the other side constantly at full humidification. These two RH cycling experiments were alternated in dry and 100% humidified conditions every 10 and 40 minutes, respectively. In the experiments, the fuel cells contained a GoreTM 57 catalyst coated membrane (CCM) and 35 BC SGL gas diffusion layers (GDLs). The fuel cell test station had been performed under idle conditions at a constant current density of 10 mA cm-2. Under the idle conditions, operating at very low current density, a low chemical degradation rate and minimal electrical load stress were anticipated. However, the membrane was expected to degrade due to additional stress from the membrane swelling/contraction cycle controlled by the RH. In this work the performance of the 100% RH humidified cell (Run 1) was compared with that of RH cycling cells (Run 2 and Run 3). Chemical and mechanical degradation of the membrane were investigated using in-situ and ex-situ diagnostic methods. The results of each measurement during and after fuel cell operation are consistent. They clearly show that changing in RH lead to an overall PEM fuel cell degradation due to the increase in membrane degradation rate from membrane resistance, fluoride ion release concentration, hydrogen crossover current, membrane thinning, and hot-spot/pin-hole formation.

Indiana University-Purdue University Indianapolis (IUPUI) / Calcium phosphate-filled restorative materials were developed to provide calcium (Ca) and phosphate (PO4) ions, which have been proposed to enhance remineralization of demineralized tooth structure. Recently, tricalcium phosphate (TCP)-filled restorative materials were introduced as an alternative to amorphous calcium phosphate. The TCP filler has a more crystalline structure than ACP and is therefore potentially stronger. The aim of the present study was to examine TCP-filled restorative resins at different concentration levels at different time intervals to characterize the concentrations of Ca and PO4 ions released, and to measure the water sorption (WS) of these resins. An in vitro study was conducted by formulating resin composite using TCP as the filler mixed with EBPADMA, HmDMA, and HEMA as the resin matrix. One-hundred- sixty samples were prepared, 40 samples of each filler concentration (30 percent, 40 percent, 50 percent, and 60 percent) by weight. From each filler concentration, 5 samples of each of the 8 time points (time intervals of 4 h, 8 h, 12 h, 24 h, 3 d, 7 d, 14 d, and 21 d) were immersed in 100-ml deionized water. Calcium and PO4 ions were measured using atomic absorption spectroscopy and light spectroscopy, respectively. Water sorption (WS) was measured according to ISO 4049 specification and then the WS and the diffusion coefficient were calculated. The significance level was set at p = 0.001. The results indicated that Ca and PO4 ion release increased with increasing filler level at a rate faster than being linear. In addition, WS results were very high and failed to meet the ISO 4049 specification requirement. Diffusion coefficient results were also high. One-way ANOVA test for only 21-day data revealed that there is a statistically significant difference in filler level percent, and two-way ANOVA testing revealed that there is a statistically significant interaction between time and filler level percent on the Ca, PO4 released and WS. It can be concluded that the concentrations of Ca and PO4 released and WS were affected by composition of the monomers, filler level and type, dispersion, and the absence of coupling agent. Although this TCP-filled restorative material may release Ca and PO4, it cannot serve as a restorative material due to high WS values. Further study is needed to improve the material and evaluate its ability in promoting remineralization of the tooth structure in order for it to serve its purpose.

Besides osteoconductivity and a high degradation rate, mesoporous bioactive glasses (MBGs) are specific for their highly ordered channel structure and high specific surface area, making them suitable as drug and/or growth factor delivery systems. On the other hand, the mesoporous channel structure and MBG composition can have an effect on common cell evaluation assays, leading to inconclusive results. This effect is especially important when MBG is mixed in composite bioinks, together with cells. Additionally, the hydrogel component of the ink can influence the degradation of MBG, leading to different ion releases, which can additionally affect the analyses. Hence, our aim here was to show how the MBG structure and composition influence common cell viability and differentiation assays when calcium (Ca)- or magnesium (Mg)-containing glass is part of an alginate-based composite bioink. We suggested pre-labeling of cells with DiI prior to bioprinting and staining with calcein-AM to allow identification of metabolically active cells expressing signals in both green and red channels, allowing the use of fluorescence imaging for cell viability evaluations in the presence of high amounts (7 wt %) of MBGs. The release and uptake of ions during degradation of CaMBG and MgMBG were significantly changed by alginate in the composite bioinks, as confirmed by higher release and uptake from bulk glasses. Additionally, we detected a burst release of Mg²⁺ from composites only after 24 h of incubation. Furthermore, we demonstrated that released ions and the mesoporous channel structure affect the measurement of lactate dehydrogenase (LDH) and alkaline phosphatase activity (ALP) in bioprinted composite scaffolds. Measured LDH activity was significantly decreased in the presence of CaMBG. On the other hand, the presence of MgMBG induced increased signal measured for the ALP. Taken together, our findings show how composite bioinks containing MBGs can interfere with common analyses, obtaining misleading results.

Previous studies of short DNA hairpins have revealed that loop and stem sequences can significantly affect the thermodynamic stability of short DNA hairpins. Nevertheless, there has not been sufficient investigation into the pressure-temperature stability of DNA hairpins, and the current thermodynamic knowledge of DNA hairpins’ stability is limited to the temperature domain. In this work, we report the effect of hydrostatic pressure on the helix-coil transition temperature (TM) for eleven short DNA hairpins at different salt concentrations by performing UV-monitored melting. The studied hairpins form by intramolecular folding of 16-base self-complementary DNA oligo¬deoxy¬ribonucleotides. Model dependent (van’t Hoff) transition parameters such as ΔHvH and transition volume (ΔV) were estimated from analysis of optical melting transitions. Experiments revealed the ΔV for denaturation of these molecules range from -2.35 to +6.74 cm3mol-1. The difference in the volume change for this transition is related to differences in the hydration of these molecules.

Previous studies of short DNA hairpins have revealed that loop and stem sequences can significantly affect the thermodynamic stability of short DNA hairpins. Nevertheless, there has not been sufficient investigation into the pressure-temperature stability of DNA hairpins, and the current thermodynamic knowledge of DNA hairpins’ stability is limited to the temperature domain. In this work, we report the effect of hydrostatic pressure on the helix-coil transition temperature (TM) for eleven short DNA hairpins at different salt concentrations by performing UV-monitored melting. The studied hairpins form by intramolecular folding of 16-base self-complementary DNA oligo¬deoxy¬ribonucleotides. Model dependent (van’t Hoff) transition parameters such as ΔHvH and transition volume (ΔV) were estimated from analysis of optical melting transitions. Experiments revealed the ΔV for denaturation of these molecules range from -2.35 to +6.74 cm3mol-1. The difference in the volume change for this transition is related to differences in the hydration of these molecules.