This master thesis describes design of suitable surface treatment technology to get component resistant to corrosion of conventional atmosphere. Given component has a shape of pin and is made of construction steel. At the beginning, there is a theoretical study of galvanic zinc coating and galvanic surface treatment in general. Then there is analysis of damaged galvanic zinc surface and its impact of corrosive resistance of that layer with collaboration with company KOZÁK SVITAVY. Corrosive resistance of damaged zinc layer is then compared with corrosive resistance of quality zinc layer. At the end of this thesis is technical and economic evaluation.

The thesis deals with the analysis of corrosion resistance of machinery used in wastewater treatment plants. The theoretical part of the thesis deals with the composition of waste water in terms of corrosion aggressiveness and describes the corrosive en-vironment in the WWTP. Furthermore, the types of corrosion are characterized and the exposed machinery of the WWTP with the highest level of corrosion is determined. The experimental part of the work is devoted to the analysis of corrosion resistance of corrosion-resistant austenitic steels and structural non-alloyed steels with duplex zinc coating and acrylate paint. Furthermore, structural low-alloyed steels with chemical-heat treatment by nitriding and ferritic nitrocarburizing in gas and structural non-alloyed steel with duplex system of phosphate + epoxy coating and zinc + epoxy coating are analysed as a possible replacement for stainless steels. The steels with duplex system of zinc + acrylate coating used in practice show little corrosion resistance (the first signs of corrosion after 12 h and 24 h). some chemical-heat treated steels and steel with duplex sys-tem of zinc + epoxy coating achieved the same corrosion resistance as stainless steels (264 h test time) and can be used in technical practice.

Influence of atmospheric and chemical environments on metal products leads usually to the corrosion damage. This master´s thesis deals with way to protect metals from corrosion, especially by polysiloxane coatings in combination with coatings containing zinc. Corrosion resistance of created coatings systems is tested by laboratory accelerated tests in corrosion chamber, where the natural atmospheric conditions are simulated. Chemical resistance in selected environments is verified by drop test. Quality characteristics coatings – thickness, adhesion to the underlying material, hardness and stability of the coating colour and gloss are evaluated too.

Within the theoretical part of the diploma thesis, a list of the main types of accelerated tests designed for the resistance of metal and polymer surface finishes. In the experimental part of diploma thesis, the rate of biological resistance of wood-based board materials is evaluated. Furthermore, the resistance of coating systems is assessed by means of accelerated tests. Resistance of modular building shells is primarily focused on degradation of coatings applied primarily on metal materials and wood materials. The tested coating systems analyze the influence of the materials and chemical base on the final weather resistance.

Diploma thesis deals with the technology of surface modifications of magnesium alloys. Basic knowledge from the field of the corrosion of metal materials. The division corrosion according to way of attack and corrosion environment, etc. There is an enumeration of ways of the corrosion defence. Questions of surface modifications with an emphasis on passivation by conversion coating and its analysis. Characteristics of magnesium and its alloys. Magnesium alloys with lithium, possibilities of its passivation and the verification of corrosion resistance. Enumeration of the used devices, chemicals and materials. characteristics of the used alloys. creation of the corrosion resistance standard. Research in passivation on the alloy containing 12 percent of lithium. The verification of the corrosion test usability based on the suggestion of the background research results. The test results for passivated as well as untreated samples and the reference material (steel). Aplication of chromate-free passivation and corrosion test on the alloy containing 12 percent of lithium.

Masters`s thesis deals with study of binder concept based on purposeful creation of ettringite, assessment of physic-mechanical properties and durability. The teoretical part is the mention of ettringite and his function in building materials, are described binder concepts based on purposeful creation of ettringite and self-levelling screed for which the controlled formation ettringite typical. In the practical part are did analysis of raw materials and the composition of the mixture, including types corrosive environment for the assessment of durability. In addition are checked properties of the proposed mixture and evaluated the appropriateness of use of each type of waste materials with regard to the resulting properties.

Introduction: An adhesive bond between hard dental tissues and composite reconstructions is exposed to mechanical load, water, bacteria, enzymes and different chemical compounds. These factors could impair durability and resistance of composite reconstructions. In contrast with extensive research of negative influence of water on degradation of adhesive bonds, the influence of chemical substances on adhesive bond has not been investigated to a greater extent. Aim: The aim of the experimental part of the thesis was to evaluate the influence of hydrogen peroxide containing tooth-whitening products and mouth rinses containing chlorhexidine and fluoride on a long-term stability of class V composite restorations created using four contemporary adhesive systems by a microleakage method. Materials and methods: The following adhesive systems were investigated: total-etch Gluma Comfort Bond (GLU), and self-etch adhesives Clearfil SE Bond (CLF), Adper Prompt (ADP) and iBond (IBO). Standardized class V cavities were prepared in 192 extracted human teeth (one cervical margin in the cementum and one in the enamel). Subsequently, the cavities were restored using microhybride composite Charisma. The specimens were then exposed to the tooth whitening system Opalescence PF 20, mouth rinse Corsodyl containing...

Hořčík a kompozity fosforečnanu vápenatého jsou slibnými materiály pro biodegradabilní a nosné implantáty určené pro regeneraci kostí. Předložená práce je zaměřena na návrh, zpracování a charakterizaci vnitřně propojených kompozitů hořčíku s fosforečnanem vápenatým (Mg/CaP). Fosforečnany vápenaté jako jsou hydroxyapatit (HA), kalcium-deficitní hydroxyapatit (CDHA) a fosforečnan vápenatý (TCP) byly syntetizovány a použity pro výrobu skafoldů s kontrolovanou porozitou pomocí metody robocastingu. Byly připraveny porézní předlisky s ortogonální mřížkou a s vnitřními makropóry o velikosti ~500 µm, které byly následně slinovány za teploty 1100 °C po dobu 5 hodin. Vnitřně propojené Mg/CaP kompozity byly připraveny infiltrací čistého hořčíku a hořčíkových slitin obsahujících malá množství vápníku nebo zinku, například 0,2 hm.% vápníku a 1 hm.% zinku do porézních keramických skafoldů. Infiltrace byla provedena pomocí námi vyvinuté a nově popsané metody známé jako “Proudem asistovaná slinovací infiltrace” (z angl. Current Assisted Metal Infiltration (CAMI)). CAMI metoda umožňuje do 15 minut infiltrovat porézní keramický předlisek roztaveným kovem. Pulzujícím elektrickým proudem bylo dosaženo rychlého tavení a následného tuhnutí Mg/CaP kompozitů. Fyzikálně-chemické vlastnosti finálních vnitřně propojených kompozitů byly stanoveny pomocí rastrovací elektronové mikroskopie, počítačové mikro-tomografie, rentgenové difrakční analýzy a optické mikroskopie za účelem stanovení fázové distribuce a interakce mezi materiály. Kromě toho byla u připravených kompozitů hodnocena jejich mechanická pevnost v tlaku, degradační rychlost pomocí různých metod a biokompatibilita spolu s pokusem o uvedení těchto typů materiálů jako potenciálních degradabilních biomateriálů určených pro výrobu desek a/nebo šroubů pro ortopedické aplikace.

The purpose of the thesis was to study chemical and corrosion resistance of selected conversion coatings. The corrosion and the possibilities of corrosion protection with focus on conversion coatings on aluminum and steel surface were described in the theoretical part. In the experimental part corrosion and chemical resistance of samples without the next treatment and samples with polyester powder coating and synthetic coating were tested.

This master thesis is focused on the binary and ternary systems with connective purposeful ettringite formation for fast hardening adhesive for ceramic tiles. It deals with the durability of these materials after exposure to the corrosive environment. It examines the physical and mechanical properties and mineralogy changes after exposure to corrosive environments. Within processing of this paper provides basic information concerning the connective concept of purposeful formation of ettringite.