This diploma thesis deals with the constructional and calculation design of boiler for blast furnace and coke gas mixture combustion, including sizing of the heating surfaces. The opening section is dedicated to a brief characterization of burned fuels. The following chapter shows the parameters and composition of the resulting fuel mixture. The main part of this thesis involves; determining the stoichiometric amount air required for combustion and the resulting flue gas, determining the boiler efficiency and steam production rate, calculations regarding the combustion chamber and the detailed design of the individual heat exchangers. At the end of the thesis the heat balance of the entire boiler is verified. Drawing documentation of boiler is also part of this diploma thesis.

The focus of this thesis is a proposal of a horizontal dual-pressure heat recovery steam generator. The introductory part includes thermal calculation, as well as a design of the layout and a design of the heat transfer surfaces and the layout of the boiler. Individual chapters are broken down according to the outline of the proposal for the arrangement of the heating surfaces, according to the parameters of the flue gas and steam. The master thesis contains a scheme of a real heat transfer temperature diagram and it also includes the calculation of connecting and downcomer pipes and drums. The final part describes the calculation of the boiler draft loss. The main idea of the thesis is accompanied by the technical documentation of the drawing of the boiler.

Master´s thesis is focusing on zero energy building with technical equipment. The building was built in 70. decade of last century. It has been using for sport and cultular events until these days. Restaurant was connected to sport hall. First part is focusing on zero energy building and technical equipment, their using, combination and optimal connecting in systém. Second part solving how many fotovoltaic panels must be in the system to reching economic advantage. In third part is solving how to connecting fotovoltaic panels to the system.

The aim of the diploma thesis is to design heating and cooling in the office building and the showroom. The theoretical part deals with large-scale heating and cooling systems. The types of these systems and their advantages and disadvantages are described here. The practical part is devoted to the design of heating and cooling in the assigned office building and the showroom. In this part, two variants of the design are considered. The first variant considers the use of a heat pump as a source of heat and cold. In the second variant of the solution, a gas condensing boiler is used as a heat source and a chiller as a cold source. The experimental part deals with measuring the properties of one ceiling panel. The main task was to determine the cooling capacity of the ceiling panel.

The task of the master project is to design a building for sports activities in Sehradice, Zlín region. First the documentation was elaborated, the second part HVAC was designed and the last part focussed on daylighting. The building has one floor and flat green roof. The building includes a fitness, a yoga room, a relax room, two saunas, changing rooms and staff room. The superstructure is designed using Heluz ceramic block walls and Spiroll panel floor structure. Façade is insulated with ETICS. HVAC is provided by two gas boilers, two mechanical ventilation units (indoors) and a cooling unit (outdoor). Domestic hot water is provided by the gas boiler and solar panels. The building uses LED lights. Electricity consumption is partially covered by photovoltaics on the roof. The building plot also includes a large carpark in front of the building. The designs were elaborated in Revit, AutoCAD and energy assessment in Deksoft software.

The goal of this diploma thesis is the design of the sanitary installations and gas main in the pension for pensioners. The building has three floors above ground and one underground floor. The building will be covered with a hiped roof. On the first floor there is the technical background of the building, Reception and kitchen with dining room. The basement is located just below the kitchen and serves as a cloakroom for kitchen staff. The building will be designed to use as much non-potable water as possible in the form of rainwater, which will be collected from the roofs. The theoretical part deals with the use of non-potable water as operating water in buildings. The calculation and project part deals with the gravity sewer system, plumbing and gas main in the building.

The aim of the master thesis is to design nearly zero-energy building of the municipal office in the city of Bojkovice. In the first part an architectural and constructional solution was designed. The building has three above-ground floors. It has a flat green roof with skylights and photovoltaics. First floor includes reception, break room, archives, offices, meeting room, kitchenette, sanitary facilities and boiler room. Second floor consists of break room, archives, storerooms, offices and sanitary facilities. External load-bearing walls, internal load-bearing walls and partitions are made of ceramic blocks. Columns, girders, floor slabs and roof slabs are made of monolithic reinforced concrete. Cladding is insulated with ETICS. In the second part HVAC was designed. Heating is provided by gas condensing boiler. The building is mechanical ventilated by AC units situated in technical room in the third above-ground floor. Cooling is air-conditioned by fan-coil units designed in offices and conference hall, chillers are situated on the roof. The third part of the master thesis focused on design and comparison of various AC units. Drawings are processed in SW AutoCAD, calculations were made in Excel, the design of air-conditioning system and unit was made in SW Atrea DUPLEX 9.10, Aerocad and CLIMACAL.

In the first part, the diploma thesis addresses the issue of comparing individual HVAC systems for family houses. The second part is an experimental measurement of HVAC systems of a low-energy family house. The third part deals with the current state of heating and air conditioning of the family house, together with a certificate of energy performance of buildings. The diploma thesis is more focused on the experimental part.

The master thesis deals with the design of environment friendly boarding house, which is located on a hill in a small village called Chlumětín. There are designed renewable energy sources, such as solar collectors or fotovoltaic panels. The first part deals with the design and layout of the boarding house. On the ground floor is solved, the design of the kitchen according to hygienic requirements, the design of the premises for guests with barrier-free toilets. In the attic are designed guest rooms including barrier-free room. The second part deals with the simplified design of building services. It includes rainwater management, mechanical ventilation with heat recovery, lighting, cooling and heating. The third part deals with the detailed design of heating in the building. It includes design of radiator power, pipe dimension, power of wood-gas boiler, storage tanks, pumps, etc.

The aim of this Master´s Thesis is to create project documentation for office building with nearly zero energy consumption. The topic of the Master´s Thesis is Office Building located in Brno Komárov. Thesis is divided in to 3 main parts. In a first part, constructional solution is proposed. Office building is designed for recruitment agency with capacity of 32 personnel that consists of 3 floors, green roof and green facade. Ground plan of designed building is in rectangular shape. On the first floor there is a reception, offices, registry, small kitchen and staff room. Second floor is similar to the first one but it has a conference room. Third floor is designed as staff room with coffee lounge. In second part of Master Thesis design of building services engineering systems is proposed. Building uses forced ventilation with heat recovery. Heating is provided by two condensing gas boilers. Supply of electric energy is partially ensured by photovoltaic power plant. In addition, rain water is effectively used in this building. In the third part evaluation of six designed compositions of floor with Life Cycle Assessment method is done. Software used to elaborate this Master´s Thesis are following: ArchiCad, DekSoft, GaBi, Excel and Lumion.