An investigation was conducted to study the constraint effects on flaw growth in composite laminates. Results were presented for the case of a transverse flaw in an interior ply perpendicular to the loading axis. Two orientations of the flawed ply were examined (0 and 90 degrees), and two distinctly different constraint situations were studied (cross-ply constraint and biaxial constraint). Throughout the study, various nondestructive testing methods were employed to evaluate the material response and to determine the damage and damage growth in the specimens. These techniques include replication, ultrasonic c-scan, ultrasonic attenuation, acoustic emission, x-radiography, thermography and stiffness measurement. The effects of constraint on the response of composite materials can be classified in two categories: (a) in-plane effects and (b) through-the-thickness effects. In-plane constraint is the principal contributor to notched strength and changes in notched strength under quasi-static loading. Through-the-thickness constraint controls the pattern and spacing of transverse cracks in the off-axis plies to form a characteristic damage state in the laminates. Out-of-plane stresses produced by constraints are influential on the growth of damage along ply interfaces, especially during cyclic loading. The mode of damage and the extent of damage in constrained notched plies are governed by the stress state in those plies, as determined by the constraining plies, and the relationship of the stress state to the strength state. Maximum constraint on the flawed ply does not produce minimum damage in the laminate; and the lesser degree of damage (in terms of axial splitting and delamination) does not necessarily result in a higher laminate strength or long fatigue lives. In the design of composite structures, a compromise has to be reached with regard to optimizing material parameters such as strength, stiffness, fatigue life, and residual strength. In maximizing one parameter, one might have to sacrifice other requirements on the other material properties in the design. / Ph. D.

A quasi-three dimensional, nonlinear elastic finite element stress analysis of finite width composite laminates including curing stresses is presented. Cross-ply, angle-ply, and some quasi-isotropic graphite/epoxy, laminates are studied. Curing stresses are calculated using temperature dependent elastic properties that are input as percent retention curves, and stresses due to mechanical loading in the form of an axial strain are calculated using tangent modulus, obtained by Ramberg Osgood parameters. It is shown that curing stresses are significant only as edge effects in angle-ply laminates, and severe throughout the laminate in cross-ply laminates. The tensor polynomial failure, criterion is used to predict the initiation of failure, and the failure mode is predicted by examining individual contributions of the stresses to the polynomial. / Master of Science

Changes in the stiffness and strength of notched quasi-isotropic graphite-epoxy laminates were recorded and related to the fatigue damage. Two different laminates [0,90,+45,-45]s (type A) and [ +45, 90, -45, 0] s (type B) were considered and the effects of stacking sequence were compared. Nondestructive testing techniques such as X-radiography, moire technique, acoustic emission, deply technique, and stiffness change were performed to observe damage development. Static properties and damage initiation were related to an approximate stress analysis. Results show that the mechanical response and the fatigue damage depend strongly on the stacking sequence of laminates. In general, residual strength increased remarkably for both laminates due to stress redistributions while the continuous stiffness change curve is typical for each laminate and reflects damage characteristics. Buckling effects as well as matrix cracking and delaminations contribute to stiffness changes. / M.S.

The effect of cooling rate and stacking sequence on fatigue behavior was analyzed for notched quasi-isotropic APC-2 laminates. The fatigue behavior of fast (475° F/min) and slow (1° F/min) cooled specimens of the following two layups was studied: Layup A of (-45/0/45/90), and Layup B of (45/90/-45/0),. All specimens were subjected to a load controlled, Tension - Tension fatigue loading with a stress ratio R = 0.1 at a frequency of 5 Hz. Parameters such as strain, temperature rise across the notch and number of cycles fatigued were continuously monitored during the fatigue tests. Damage was monitored by the reduction in modulus, penetrant enhanced X-ray radiography, and Scanning Acoustic Microscopy (SAM). Post failure analysis of the specimens was carried out by Scanning Electron Microscopy (SEM). A quasi-3D Finite Element Analysis was performed to compare the differences in the interlaminar stresses arising around the notch in the specimens of the two layups under study. The ultimate static strengths did not show any appreciable dependence on either cooling rate or stacking sequence. The maximum load in the fatigue cycle was selected as a fraction of the ultimate notched static tensile strength in each case. The fatigue lives showed appreciable difference between the two cooling rates in layup A when tested at the lower load levels. The fatigue behavior was vastly different between the two cooling rates for specimens of layup B. Also, specimens of layup B, both fast and slow cooled, had longer lives than their counterparts from layup A. A model, based on a constant strain-to-failure criterion, was developed for life prediction and the predicted lives are in good agreement with the experimental values. Fast cooled specimens of layup A showed a gradual degradation in the modulus till failure while slow cooled specimens of the same layup showed a more drastic reduction as they approached failure. No such distinguished behavior was observed in the specimens of layup B. Scanning Electron Micrographs of the fast cooled specimens indicate better fiber/matrix bonding conditions and more matrix plasticity as compared to the slow cooled specimens. A rotated stacking sequence technique was used for the calculation of the interlaminar stresses around the notch. No single stress seems to control failure but it is likely that failure occurs by the interaction of the different stresses since a three-dimensional stress state exists at the notch. Based on this reasoning, effective stresses were calculated at all those interfaces where one of the interlaminar (normal or shear) stresses has a maximum value. A comparison of the effective stresses calculated showed the layup A to be 1.7 times more prone to delamination than layup B. Damage analysis of the fatigued specimens by X-ray radiography and Scanning Acoustic Microscopy shows the specimens of layup A to be dominated by delaminations as compared to those of layup B. The interfaces predicted to be critical by FEA agreed well with the experimental observations, in general. / Master of Science

Based on the principle of virtual displacements, the incremental equations of motion of a continuous medium are formulated by using the total Lagrangian description. After linearization of the incremental equations of motion, the displacement finite element model is obtained, which is solved iteratively. From this displacement finite element model, four different elements, i.e. degenerated shell element, degenerated curved beam element, 3-D continuum element and solid-shell transition element, are developed for the geometric nonlinear analysis of general shell-type structures, anisotropic as well as isotropic. Compatibility and completeness requirements are stressed in modelling the general shell-type structures in order to assure the convergence of the finite-element analysis. For the transient analysis Newmark scheme is adopted for time discretization. An iterative solution procedure, either Newton-Raphson method or modified Riks/Wempner method, is employed to trace the nonlinear equilibrium path. The latter is also used to perform post-buckling analysis. A variety of numerical examples are presented to demonstrate the validity and efficiency of various elements separately and in combination. The effects of boundary conditions, lamination scheme, transverse shear deformations and geometric nonlinearity on static and transient responses are also investigated. Many of the numerical results of general shell-type structures presented here could serve as references for future investigations. / Ph. D.

No description available.

Thesis (M.S.)--State University of New York at Binghamton, Thomas J. Watson School of Engineering and Applied Science, Department of Systems Science and Industrial Engineering, 2009. / Includes bibliographical references.

Within the past several years, researchers have detected the presence of a third “phase” between the bulk fiber phase and bulk matrix phase in a polymeric matrix composite. This finite-thickness region — termed the interphase — possesses mechanical, physical, and chemical properties that are distinct from the fiber and matrix constituents. Thus, the interphase embodies the characteristics of the fiber/matrix bond, including the strength and stiffness of the bond. In essence, the interphase represents the composite system, since it defines the level of synergistic interaction that occurs between the load-carrying fibers and the binding matrix material. Recent interest in the interphase has spawned international conferences and a technical journal devoted to its study. Despite this spate of research, some very fundamental questions about the interphase have remained unanswered. One such question is: “What is best for the performance of a composite, a strong or weak or intermediate-strength interphase?” It is surprising that this question is even asked, since, until recently, it had been assumed that the stronger the fiber/matrix bond, the better the composite behavior. It is now known that this adage is far from true. Two formidable challenges await those who wish to correlate the strength of the interphase to the mechanical performance of polymeric matrix composite materials. First, one seeks to systematically alter the interphase in order to exploit this variable. In this study, fourteen material systems representing permutations of four carbon fibers, three matrix systems, percentages of fiber surface treatment, and three sizing conditions have been examined. Secondly, one needs to quantitatively characterize the properties of the resultant interphase in order to correlate the bond condition to the composite’s mechanical behavior. This investigation utilizes two techniques, the Continuous Ball Indentation Test and transverse flexure testing, as a means of interrogating the strength of the interphase. The influence of the interphase on the tensile and compressive strength and modulus of crossplied laminates possessing a center hole is investigated. Unnotched angle-ply ([±45]_ns) laminates are also tested in order to assess the role of the interphase in the strength of a “matrix-dominated” laminate. Fully-reversed (R =-1), axial fatigue of notched cross-plied laminates from each of the fourteen material systems 1s performed. During fatigue testing several data are monitored, including cycles to failure, dynamic modulus, and notch temperature. The tension-tension (R= 0.1) fatigue response of the unnotched angle-ply laminates is also studied. Results from X-ray radiography of fatigue-damaged specimens help to explain the relationship between the interphase and the initiation and propagation of life-critical damage mechanisms. Having observed the formative role played by the interphase in the performance of these laminates, an attempt is made to introduce variables representing the interphase into micromechanical models of composite behavior. / Ph. D.

A method for reinforcing the free edges of a symmetric 11-ply graphite-epoxy laminate by adding a one-layer Kevlar-epoxy edge cap is studied. Generalized plane strain finite element analysis is used to predict that interlaminar stresses are reduced when an edge cap is added to the laminate. Different edge cap designs are evaluated. A three-dimensional composite failure criterion and finite element analysis are used in a progressive laminate failure analysis to predict the failure load of the reinforced luminate. The results of an experimental program are presented. Cappad laminates are shown to be on average 130% to 140%. stronger than uncapped laminates when subjected to static tensile or tension-tension fatigue loading. In addition, the coefficient of variation of the static tensile failure load decreases from 24% to 8% with the addition of edge caps. The predicted failure load which is calculated with the finite element results is 10%. lower than the actual failure load. For both the capped and the uncapped laminates, actual failure loads are much lower than those predicted using classical lamination theory stresses and a 2-D failure criterion. Possible applications of the free edge reinforcement concept are given. Suggestions for future research are made. / M.S.

M.S.