Thin film silicon on low temperature glass substrates is currently seen as the best path toreduce the $/W cost of photovoltaic (PV) modules. However, producing thin film polysilicon, on glass, is an ongoing research challenge. Laser crystallisation of a-Si is one of the possible methods. Typically excimer (XMR) lasers are used for laser crystallisation. This thesis introduces the copper vapour laser (CVL) as a viable alternative for thin film photovoltaic applications. The CVL, like the XMR, is a high powered, pulsed laser. However, the CVL has higher pulse rates (4-20kHz), better beam quality and a visible wavelength output (578 & 511nm). Preliminary experiments, using 600K-heated silicon-on-quartz samples, confirmed that CVL crystallisation can produce area weighted average grain size of 0.1-0.15??m, which is comparable to results reported for XMR??? s. Importantly, the CVL results used thicker films (1??m), which is more applicable to thin photovoltaic devices that need 1-10??m of silicon to be viable. The CVL??? s longer wavelength and therefore longer penetration depth (1/alpha) are proffered as the main reason for this result. Extensive laser-thermal modelling highlighted further opportunities specific to CVL crystallisation. Through-the-glass doublesided irradiation was shown in simulations to reduce thermal gradients, which would enhance crystal growth. The simulations also produced deeper melts at lower surface temperatures, reducing the thermal stress on the sample. Subsequent experiments, using silicon-on-glass, confirmed the benefit of through-the-glass doublesided irradiation by maintaining grain sizes without the usual need for substrate heating. Furthermore, Raman analysis showed that doublesided crystallisation achieved full depth crystallisation, unlike single side irradiation which produced partial crystallisation. A new mode of crystallisation, stepwise crystallisation, was also postulated whereby a series of CVL pulses could be used to incrementally increase the crystallisation depth into the silicon. Simulations confirmed the theoretical basis of the concept, with HeNe Raman spectroscopy and analysis of surface grain sizes providing indirect experimental support. The CVL??? s ability to crystallise thicker films more directly applicable to photovoltaic devices secures its viability as an alternative laser for photovoltaic applications. The through-the-glass doublesided irradiation and the stepwise crystallisation provide additional potential for increased process flexibility over XMR???s.

Thin film silicon on low temperature glass substrates is currently seen as the best path toreduce the $/W cost of photovoltaic (PV) modules. However, producing thin film polysilicon, on glass, is an ongoing research challenge. Laser crystallisation of a-Si is one of the possible methods. Typically excimer (XMR) lasers are used for laser crystallisation. This thesis introduces the copper vapour laser (CVL) as a viable alternative for thin film photovoltaic applications. The CVL, like the XMR, is a high powered, pulsed laser. However, the CVL has higher pulse rates (4-20kHz), better beam quality and a visible wavelength output (578 & 511nm). Preliminary experiments, using 600K-heated silicon-on-quartz samples, confirmed that CVL crystallisation can produce area weighted average grain size of 0.1-0.15??m, which is comparable to results reported for XMR??? s. Importantly, the CVL results used thicker films (1??m), which is more applicable to thin photovoltaic devices that need 1-10??m of silicon to be viable. The CVL??? s longer wavelength and therefore longer penetration depth (1/alpha) are proffered as the main reason for this result. Extensive laser-thermal modelling highlighted further opportunities specific to CVL crystallisation. Through-the-glass doublesided irradiation was shown in simulations to reduce thermal gradients, which would enhance crystal growth. The simulations also produced deeper melts at lower surface temperatures, reducing the thermal stress on the sample. Subsequent experiments, using silicon-on-glass, confirmed the benefit of through-the-glass doublesided irradiation by maintaining grain sizes without the usual need for substrate heating. Furthermore, Raman analysis showed that doublesided crystallisation achieved full depth crystallisation, unlike single side irradiation which produced partial crystallisation. A new mode of crystallisation, stepwise crystallisation, was also postulated whereby a series of CVL pulses could be used to incrementally increase the crystallisation depth into the silicon. Simulations confirmed the theoretical basis of the concept, with HeNe Raman spectroscopy and analysis of surface grain sizes providing indirect experimental support. The CVL??? s ability to crystallise thicker films more directly applicable to photovoltaic devices secures its viability as an alternative laser for photovoltaic applications. The through-the-glass doublesided irradiation and the stepwise crystallisation provide additional potential for increased process flexibility over XMR???s.