<p>Trapped ion systems are the leading candidate for quantum information processing because many of the critical components have already been demonstrated. Scaling trapped ion systems to large numbers of ions is currently believed possible, but much work remains to prove it. Microfabricated surface ion traps are increasing in popularity for their ease of mass production and their ability to manipulate individual ions and interact arbitrary pairs of ions. Even with the advent of scalable ion traps, detection of an individual ion trapped in a high vacuum poses a challenge. The internal state of the ion chosen for a quantum bit can be measured via exposure to a probe beam that causes one state to scatter light (a "bright" state), but not the other state (a "dark" state). In free space, a single ion acts like a point source that emits in all directions; a standard two inch lens system can only collect about 2% of the light emitted by the ion. Poor light collection results in a high error rate and slow determination of the internal state of the ion. Fast, high fidelity state detection is necessary for quantum error correction and loophole-free Bell experiments at short (less than 100\,km) distances, and high efficiency collection is necessary to rapidly interconnect separate quantum computers. We demonstrate state detection fidelities of 99%, 99.856(8)% and 99.915(7) % which correspond to detection times of 10.5, 28.1 and 99.8 us, respectively.</p> / Dissertation

Résumé : Les performances de détecteurs à scintillation, composés d’un cristal scintillateur couplé à un photodétecteur, dépendent de façon critique de l’efficacité de la collecte et de l’extraction des photons de scintillation du cristal vers le capteur. Dans les systèmes d’imagerie hautement pixellisés (e.g. TEP, TDM), les scintillateurs doivent être arrangés en matrices compactes avec des facteurs de forme défavorables pour le transport des photons, au détriment des performances du détecteur. Le but du projet est d’optimiser les performances de ces détecteurs pixels par l'identification des sources de pertes de lumière liées aux caractéristiques spectrales, spatiales et angulaires des photons de scintillation incidents sur les faces des scintillateurs. De telles informations acquises par simulation Monte Carlo permettent une pondération adéquate pour l'évaluation de gains atteignables par des méthodes de structuration du scintillateur visant à une extraction de lumière améliorée vers le photodétecteur. Un plan factoriel a permis d'évaluer la magnitude de paramètres affectant la collecte de lumière, notamment l'absorption des matériaux adhésifs assurant l'intégrité matricielle des cristaux ainsi que la performance optique de réflecteurs, tous deux ayant un impact considérable sur le rendement lumineux. D'ailleurs, un réflecteur abondamment utilisé en raison de ses performances optiques exceptionnelles a été caractérisé dans des conditions davantage réalistes par rapport à une immersion dans l'air, où sa réflectivité est toujours rapportée. Une importante perte de réflectivité lorsqu'il est inséré au sein de matrices de scintillateurs a été mise en évidence par simulations puis confirmée expérimentalement. Ceci explique donc les hauts taux de diaphonie observés en plus d'ouvrir la voie à des méthodes d'assemblage en matrices limitant ou tirant profit, selon les applications, de cette transparence insoupçonnée. / Abstract : The performance of scintillation detectors, made up of a scintillating crystal coupled to a photodetector, critically depends on the collection and extraction efficiency of scintillation photons from the crystal by the sensor. In highly pixelated imaging systems (e.g. PET, CT), scintillators must be arranged in compact arrays with form factors detrimental to light transport, deteriorating the detector performance. The goal of the study was to optimize the pixelated detectors performance by identifying the light loss sources related to the spectral, spatial and angular characteristics of the scintillation photons impinging on scintillators faces. Such information acquired by Monte Carlo simulations enables adequate weighting for the evaluation of achievable gains through structuring of the scintillators for enhanced light extraction to the photodetector. The magnitude of parameters affecting the light collection in arrays, such as adhesive materials absorption and reflector opacity that both have high impact on light output, was evaluated through a factorial design. A frequently used reflector because of its outstanding optical performance was characterized in more realistic conditions compared to air immersion in which its reflectivity is always reported. An important reflectivity quenching of the reflector in optically bonded scintillator arrays was discovered by simulation and confirmed experimentally. This explains the high light crosstalk measured in pixelated arrays as well as paving the way to assembling methods limiting or taking advantage, depending on the application, of this unsuspected transparency.

A new measurement of the neutron electric dipole moment (nEDM) is being developed at TRIUMF, where a high density source of ultra cold neutrons (UCN) is currently under construction. A fast, high-efficiency UCN detector is needed for the experiment, and a 6-Li doped glass scintillation detector is being explored for this purpose. In this work, simulations and test measurements were carried out to optimize the light guide design for the new UCN detector. Acrylic and air-core light guides, the latter with two different reflecting surfaces, were considered. Three prototype light guides were constructed and tested, and results were compared with simulations. The best solution was found to be an acrylic guide, wrapped with mylar foil. For a guide 12 cm in length as required by the experimental layout, a lower limit of approximately 25 photoelectrons per neutron capture was established for the proposed geometry and photomultiplier configuration. / May 2016