<p>The predicted growth in demand for electric vehicles (EVs) has given rise to increasing use of lithium-ion batteries (LIBs), which are the source of energy used in all EVs. Recycling of spent LIBs not only can supply more materials to manufacturing new LIBs, but also can mitigate haz-ardous waste disposal in the environment. Direct recycling focuses on separating cathode materials to be re-purposed or remanufactured. Delamination of cathode materials is the necessary first step; however, it is fraught with difficulties due to the strong adhesive forces provided by the polyvi-nylidene fluoride (PVDF) binder that is widely used in LIBs. The widely accepted delamination methods are N-Methyl-2-pyrrolidone (NMP) solvent dissolution and direct calcination, which are not desirable due to either environmental and health concerns or high energy consumption.</p> <p>The lithium chemical systems (LiCl, LiNO₃, and LiOH) and their binary eutectic systems, were systematically studied to recover heterogeneous cathode active materials (NMC 111 and LMO) from spent LIBs of EVs. The LiOH-LiNO₃ eutectic system showed 98.3% peel-off effi-ciency under preferable conditions. The recycled products were characterized using ICP-OES, XPS, SEM, and XRD. There were minimal changes in chemical composition, morphology, or crystal structure of the recycled cathode materials after LiOH-LiNO3 eutectic treatment, compared with those recycled with an AlCl₃-NaCl eutectic molten salt treatment that introduces more Al contamination and morphological defects.  </p> <p>In order to avoid corrosive chemicals and minimize particle agglomeration, additional lith-ium salts were investigated, including LiOAc (lithium acetate), Li₂CO₃, and Li₂SO₄. A peel-off efficiency of up to 98.5% was achieved at a LiOAc to LiNO₃ molar ratio of 3:2, salt to cathode mass ratio of 10:1, temperature of 300° C, and a holding time of 30 minutes. To validate the effect of the cations, the recycled products from the molten sodium salt system (NaOAc-NaNO3) were tested. The lithium salt system achieved separation at a lower temperature. Use of LiOAc-LiNO₃ minimized morphological changes compared with direct calcination.</p> <p>The effective separation in LiOH-LiNO3 or LiOAc-LiNO3 molten salt systems was based on promotion of PVDF decomposition, and these two systems may be feasible for recycling other typical cathodes (LCO and LFP) where PVDF is used as the binder. Use of molten lithium salts as alternatives to direct calcination or use of other solvents, may help facilitate recycling of spent LIBs, and even achieve a way for closed loop direct recycling of materials.</p> <p> Additionally, a chemical-free pressure washing system was studied to overcome the adhe-sion provided by PVDF. Although the pressure washing system was not able to remove PVDF from the cathode materials, nearly instant separation from the aluminum backing was achieved when the shear stress and normal stress provided by the impacting of high-pressure waterjet was stronger than the binding forces. Factors investigated included water pressure, distance between the nozzle and cathode, the incident angle of the water jet, and the nozzle type (sprayer angle). A 34-1 fractional factorial design was used to evaluate the parameters and find the optimal operating conditions. A small amount of Al and consistent morphology (of nearly pristine cathode active materials) were detected. Three kinds of recycled cathode materials (NMC&LMO, LCO, and LFP) were used as inputs to investigate a sulfuric acid leaching process, indicating high leaching effi-ciencies (lithium > 90% and cobalt > 85%).</p> <p>The degradation of cathode active materials or PVDF affects the adhesion force between cathode materials layer and Al current collector. Because delamination replies on inactivation of bonding forces provided by PVDF, it is believed that the storage environment (air, O₂ or H_{<strong>2</strong>}O) will affect the performances of delamination to some extent. Three representative methods (direct cal-cination, solvent extraction, and pressure washing system) of delamination were selected to eluci-date the effect from air exposure time. Direct calcination was barely influenced and stably sepa-rated CAMs in terms of peel-off efficiency. The pressure washing system or solvent extraction exhibited high peel-off efficiency using control samples, but the performance regarding either Al contamination or separation efficiency  significantly worsened after long air exposure time. This hypothesis could explain lack of reproducibility of some results in different studies and highlight the importance of strict storage condition of spent LIBs to direct recycling technology. </p> <p>Overall, this thesis examines innovative delamination methods for the development of cost-efficient and environmentally friendly direct recycling of spent LIBs. Application of the eutectic molten lithium salt system (LiOH-LiNO₃ and LiOAc-LiNO₃) or pressure washing system indicates promising benefits to reduce toxic gas emission and energy consumption, and accelerate the cir-cular economy.</p>

Transition metals (TMs) are ‘elements whose atoms have partially filled d-shell, or which can give rise to cations with an incomplete d-shell’. In TMs, the d-shell overlaps with next higher s-shell. Most of the TMs exhibit more than one (multiple) oxidation states. Some TMs, such as silver and gold, occur naturally in their metallic state but, most of the TM minerals are generally oxides. Most of the minerals on the planet earth are metal oxides, because of large free energies of formation for the oxides. The thermodynamic stability of the oxides is determined from the Ellingham diagram. Ellingham diagram shows the temperature dependence of the stability (free energy) for binaries such as metal oxides. Ellingham diagram also shows the ease of reducibility of metal oxides. TM oxides of general formulas MO, M2O3, MO2, M2O5, MO3 are known to exist, many of them being the ultimate products of oxidation in air in their highest oxidation states. In addition, TM oxides also exist in lower oxidation states which are prepared under controlled conditions. The nature of bonding in these oxides varies from mainly ionic (e.g. NiO, CoO) to mainly covalent (e.g. OsO4). Simple binary oxides of the compositions, MO, generally possess the rock salt structure (e.g. NiO), while the dioxides, MO2, possess the rutile structure (e.g. TiO2); many sesquioxides, M2O3, possess the corundum structure (e.g. Cr2O3). TMs form important ternary oxides like perovskites (e.g. CaTiO3), spinels (e.g. MgFe2O4) and so on. In TM oxides, the valence (outer) d-shell could be empty, d0 (e. g. TiO2), partially filled, dn (1≤ n≤ 9) (e.g. TiO, VO, NiO etc.) or completely filled, d10 (e.g. ZnO, CdO, Cu2O etc.). The outer d electrons in TM oxides could be localized or delocalized. Localized outer d electrons give insulators/semiconductors, while delocalized/itinerant d electrons make the TM oxide ‘metallic’ (e.g. ReO3, RuO2). Partially filled dn states are normally expected to give rise to itinerant (metallic) electron behaviour. But most of TM oxides with partially filled d shell are insulators because of special electronic energy (correlation energy) involved in d electron transfer to adjacent sites. Such insulating TM oxides are known as Mott insulators (e. g. NiO, CoO etc.). Certain TM oxides are known to exhibit both localized (insulating) and itinerant (metallic) behaviour as a function of temperature or pressure. For example, VO2 shows a insulator–metal transition at ~340K. Similar transitions are also known for V2O3, metal-rich EuO and so on. The chemical composition and bonding of TM oxides, which determine the crystal and electronic structures, give rise to functional properties. Table 1 gives representative examples. Properties like ionic conductivity and diffusion are governed by both the crystal structure and the defect structure (point defects), whereas properties such as magnetism and electron transport mainly arise from the electronic structures of the materials. Accordingly, TM oxides provide a platform for exploring functional materials properties. Among the various functional materials properties exhibited by transition metal oxides, the present thesis is devoted to investigations of lithium ion battery cathodes, inorganic pigments and magnetic perovskites. Over the years, most of the lithium containing first row transition metal oxides of rock salt derived structure have been investigated for possible application as cathode materials in lithium ion batteries (LIBs). First major breakthrough in LIBs research was achieved by electrochemically deinserting and inserting lithium in LiCoO2. A new series of cathode materials for LIBs were prepared by incorporating excess lithium into the transition metal containing layered lithium oxides through solid solution formation between Li2MnO3–LiMO2 (M = Cr, Mn, Fe, Co, Ni), known as lithium-rich layered oxides (LLOs). LLOs exhibit improved electrochemical performance as compared to the corresponding end members and hence received significant attention as a potential next generation cathode materials for LIBs in recent times. LiCoO2 (R-3m) crystallizes in the layered α-NaFeO2 structure with the oxygens in a ccp arrangement. Li+ and Co3+ ions almost perfectly order in the octahedral sites (3a and 3b) to give alternating (111) planes of LiO6 and CoO6 octahedra. Table 1. Materials properties exhibited by representative TM oxides. Property Example(s) Ferroelectricity BaTiO3, PbTiO3, Bi4Ti3O12 Nonlinear Optical Response LiNbO3 Multiferroic response BiFeO3, TbMnO3 Microwave dielectric properties Ba3ZnTa2O9 Relaxor Dielectric Properties Pb3MgNb2O9, Colossal Magnetoresistance Tl2Mn2O7 Metallic ‘Ferroelectricity’ Cd2Re2O7 Superconductivity AOs2O6(A = K, Rb, Cs) Redox deinsertion/insertion of LiCoO2 lithium Photocatalysis/water splitting TiO2 Pigment Ca(1-x)LaxTaO(2-x)N1+x (yellow-red), YIn1-xMnxO3 (blue) Metallic Ferromagnetism CrO2 Antiferromagnetism NiO, LaFeO3 Zero thermal expansion ZrW2O8 The reversible capacity of LiCoO2 in common LIBs is relatively low at around 140 mA h g-1 (half of theoretical capacity), corresponding to: LiCo3+O2 → Li0.5Co3+0.5Co4+0.5O2 + 0.5Li+ + 0.5e– . Substitution of one or more transition metal ions in LiCOO2 has been explored to improve the electrochemical performance. The structure of LLOs is described as a solid solution or nano composite of Li2MnO3 (C2/m) and LiMO2 (R-3m). The electrochemical deinsertion/insertion behaviour of LLOs is complex and also not yet understood completely. The present thesis consists of four parts. After a brief introduction (Part 1), Part 2 is devoted to materials for Li-ion battery cathode, consisting of three Chapters 2.1, 2.2 and 2.3. In Chapter 2.1, we describe the synthesis, crystal structure, magnetic and electrochemical characterization of new LiCoO2 type rock salt oxides of formula, Li3M2RuO6 (M = Co, Ni). The M =Co oxide adopts the LiCoO2 (R-3m) structure, whereas the M = Ni oxide also adopts a similar layered structure related to Li2TiO3. Magnetic susceptibility measurements reveal that in Li3Co2RuO6, the oxidation states of transition metal ions are Co3+, Co2+ and Ru4+, whereas in Li3Ni2RuO6, the oxidation states are Ni2+ and Ru5+. Li3Co2RuO6 orders antiferromagnetically at ~10K. On the other hand, Li3Ni2RuO6 presents a ferrimagnetic behaviour with a Curie temperature of ~100K. Electrochemical Li-deinsertion/insertion studies show that high first charge capacities (between ca.160 and 180 mA h g−1) corresponding to ca.2/3 of theoretical capacity are reached albeit, in both cases, capacity retention and cyclability are not satisfactory. Chapter 2.2 presents a study of new ruthenium containing LLOs, Li3MRuO5 (M = Co and Ni). Both the oxides crystallize in the layered LLO type LiCoO2 (α-NaFeO2) structure consisting of Li[Li0.2M0.4Ru0.4]O2 layers. Magnetic susceptibility data suggest that the oxidation states of transition metals are Li3Co3+Ru4+O5 for the M = Co compound and Li3Ni2+Ru5+O5 for the M = Ni compound. Electrochemical investigations of lithium deintercalation–intercalation behaviour reveal that both Co and Ni phases exhibit attractive specific capacities of ca. 200 mA h g-1 at an average voltage of 4 V, that has been interpreted as due to the oxidation of Co3+ and Ru4+ in Li3CoRuO5 and Ni2+ to Ni4+ in the case of Li3NiRuO5. Thus, we find that ruthenium plays a favourable role in LLOs than in non-LLOs in stabilizing higher reversible electrochemical capacities. In Chapter 2.3, we describe the synthesis, crystal structure and lithium deinsertion–insertion electrochemistry of two new LLOs, Li3MRuO5 (M=Mn, Fe) which are analogs of the oxides described in Chapter 2.2. The Li3MnRuO5 oxide adopts a structure related to Li2MnO3 (C2/m), while the Li3FeRuO5 oxide adopts a near-perfect LiCoO2 (R-3m) structure. Lithium electrochemistry shows typical behaviour of LLOs for both oxides, where participation of oxide ions in the electrochemical processes is observed. A long first charge process with capacities of 240 mA h g-1 (2.3 Li per f.u.) and 144 mA h g-1 (1.38 Li per f.u.) is observed for Li3MnRuO5 and Li3FeRuO5, respectively. Further discharge–charge cycling points to partial reversibility. X-ray photoelectron spectroscopy (XPS) characterisation of both pristine and electrochemically oxidized Li3MRuO5 reveals that in the Li3MnRuO5 oxide, Mn3+ and Ru4+ are partially oxidized to Mn4+ and Ru5+ in the sloping region at low voltage, while in the long plateau, O2- is also oxidized. In the Li3FeRuO5 oxide, the oxidation process appears to affect only Ru (4+ to 5+ in the sloping region) and O2- (plateau), while Fe seems to retain its 3+ state. Another characteristic feature of TMs is formation of several coloured solid materials where d–d transitions, band gap transitions and charge transfer transitions are involved in the colouration mechanism. Coloured TM oxides absorbing visible light find important applications as visible light photocatalyst (for example, yellow BiVO4 for solar water splitting and red Sr1-xNbO3 for oxidation of methylene blue) and inorganic pigments [for example, Egyptian blue (CaCuSi4O10), Malachite green (Cu2CO3(OH)2), Ochre red (Fe2O3)]. Pigments are applied as colouring materials in inks, dyes, paints, plastics, ceramic glazers, enamels and textiles. In this thesis, we have focused on the coloured TM oxides for possible application as inorganic pigments. Generally, colours arise from electronic transitions that absorb visible light. Colours of the inorganic pigments arise mainly from electronic transitions involving TM ions in various ligand fields and charge transfer transitions governed by different selection rules. The ligand field d–d transitions are parity forbidden but are relaxed due to various reasons, such as distortion (absence of center of inversion) and vibronic coupling. The d-electrons can be excited by light absorption in the visible region of the spectrum imparting colour to the material. Charge transfer transitions in the visible region are not restricted by the parity selection rules and therefore give intense colours. Here we have investigated the colours of manganese in unusual oxidation state (Mn5+) as well as the colours of different 3d-TM ions in distorted octahedral and trigonal prismatic sites in appropriate colourless crystalline host oxides. These results are discussed in Part 3 of the thesis. In Chapter 3.1, we describe a blue/green inorganic material, Ba3(P1−xMnxO4)2 (I) based on tetrahedral Mn5+O4 :3d2 chromophore. The solid solutions (I) which are sky-blue and turquoise-blue for x ≤ 0•25 and dark green for x ≥ 0•50, are readily synthesized in air from commonly available starting materials, stabilizing the Mn5+O4 chromophore in an isostructural phosphate host. We suggest that the covalency/ionicity of P–O/Mn–O bonds in the solid solutions tunes the crystal field strength around Mn(V) such that a blue colour results for materials with small values of x. The material could serve as a nontoxic blue/green inorganic pigment. In Chapter 3.2, an experimental investigation of the stabilization of the turquoise-coloured Mn5+O4 chromophore in various oxide hosts, viz., A3(VO4)2 (A = Ba, Sr, Ca), YVO4, and Ba2MO4 (M = Ti, Si), has been carried out. The results reveal that substitution of Mn5+O4 occurs in Ba3(VO4)2 forming the entire solid solution series Ba3(V1−xMnxO4)2 (0 < x ≤ 1.0), while, with the corresponding strontium derivative, only up to about 10% of Mn5+O4 substitution is possible. Ca3(VO4)2 and YVO4 do not stabilize Mn5+O4 at all. With Ba2MO4 (M = Ti, Si), we could prepare only partially substituted materials, Ba2M1−xMn5+xO4+x/2 for x up to 0.15, that are turquoise-coloured. We rationalize the results that a large stabilization of the O 2p-valence band states occurs in the presence of the electropositive barium that renders the Mn5+ oxidation state accessible in oxoanion compounds containing PO43−, VO43−, etc. By way of proof-of-concept, we synthesized new turquoise-coloured Mn5+O4 materials, Ba5(BO3)(MnO4)2Cl and Ba5(BO3)(PO4)(MnO4)Cl, based on the apatite – Ba5(PO4)3Cl – structure. Chapter 3.3 discusses crystal structures, and optical absorption spectra/colours of 3d-transition metal substituted lyonsite type oxides, Li3Al1-xMIIIx(MoO4)3 (0< x ≤1.0) (MIII = Cr, Fe) and Li3-xAl1-xMII2x(MoO4)3 (0< x ≤1.0) (MII = Co, Ni, Cu). Crystal structures determined from Rietveld refinement of PXRD data reveal that in the smaller trivalent metal substituted lyonsite oxides, MIII ions occupy the octahedral (8d, 4c) sites and the lithium ions exclusively occur at the trigonal prismatic (4c) site in the orthorhombic (Pnma) structure; on the other hand, larger divalent cations (CoII/CuII) substituted derivatives show occupancy of CoII/CuII ions at both the octahedral and trigonal prismatic sites. We have investigated the colours and optical absorption spectra of Li3Al1-xMIIIx(MoO4)3 (MIII = Cr, Fe) and Li3-xAl1-xMII2x(MoO4)3 (MII = Co, Ni, Cu) and interpreted the results in terms of average crystal field strengths experienced by MIII/MII ions at multiple coordination geometries. We have also identified the role of metal-to-metal charge transfer (MMCT) from the partially filled transition metal 3d orbitals to the empty Mo – 4d orbitals in the resulting colours of these oxides. B The ABO3 perovskite structure consists of a three dimensional framework of corner shared BO6 octahedra in which large A cation occupies dodecahedral site, surrounded by twelve oxide ions. The ideal cubic structure occurs when the Goldschmidt’s tolerance factor, t = (rA + rO)/{√2(rB + rO)}, adopts a value of unity and the A–O and B–O bond distances are perfectly matched. The BO6 octahedra tilt and bend the B – O – B bridges co-operatively to adjust for the non-ideal size of A cations, resulting deviation from ideal cubic structure to lower symmetries. Ordering of cations at the A and B sites of perovskite structure is an important phenomenon. Ordering of site cations in double (A2BB'O6) and multiple (A3BB'2O9) perovskites give rise to newer and interesting materials properties. Depending upon the constituent transition metals and ordering, double perovskite oxides exhibit a variety of magnetic behaviour such as ferromagnetism, ferrimagnetism, antiferromagnetism, spin-glass magnetism and so on. We also have coupled magnetic properties such as magnetoresistance (Sr2FeMoO6), magnetodielectric (La2NiMnO6) and magnetooptic (Sr2CrWO6) behaviour. Here we have investigated new magnetically frustrated double perovskite oxides of the formula Ln3B2RuO9(B = Co, Ni and Ln = La, Nd). The Chapter 4.1 describes Ln3B2RuO9 (B = Co, Ni and Ln = La, Nd) oxides (prepared by a solid state metathesis route) which adopt a monoclinic (P21/n) A2BB'O6 double perovskite structure, wherein the two independent octahedral 2c and 2d sites are occupied by B2+ and (B2+1/3Ru5+2/3) atoms, respectively. Temperature dependence of the molar magnetic susceptibility plots obtained under zero field cooled (ZFC) condition exhibit maxima in the temperature range 25–35K, suggesting an antiferromagnetic interaction in all these oxides. Ln3B2RuO9 oxides show spin-glass behavior and no long-range magnetic order is found down to 2 K. The results reveal the importance of competing nearest neighbour (NN), next nearest neighbor (NNN) and third nearest neighbour (third NN) interactions between the magnetic Ni2+/Co2+ and Ru5+ atoms in the partially ordered double perovskite structure that conspire to thwart the expected ferromagnetic order in these materials.