This thesis presents the design of various closed-loop real-time control of a novel linear magnetostrictive actuator. The novel linear magnetostrictive actuator which uses Terfenol-D as the magnetostrictive material was developed by Sadighi. It solves the problem of power consumption in a conventional magnetostrictive actuator. However, the control system of this magnetostrictive actuator cannot control the current in the coils, which limits the performances of the real-time position control. In the closed-loop real-time control system proposed in this thesis, the controller is designed depending on the change of current. The closed-loop real-time control design focused on the position control of the active element in the novel linear magnetostrictive actuator. The closed-loop position-control system of the linear magnetostrictive actuator was successfully designed by implementing a closed-loop current-control system as an inner loop of the entire control system. This design offers the flexibility to design various position controllers in the closed-loop position-control system. The closed-loop current-control design uses pulse-width modulation (PWM) signal to change the current in the coils of the novel linear magnetostrictive actuator. By changing the duty ratio of the PWM signal, the current in the coils can be changed from zero to its maximum value. With a current controller using an integrator with a gain of 10, the current can be controlled with high response time and an error of /- 0.01 A. The position-controller design was successfully conducted by using four different approaches. First, a proportional-integral-derivative (PID) controller which was designed by relay-auto tuning method with experiments exhibited a position error of ±1 μm with a 5 μm peak-to-peak position noise. Second, a PID controller which was designed by root-locus can control the position with a position error of /- 3-4 μm with a 5 μm peak-to-peak position noise. Third, a linear variable velocity controller exhibited a position error of /-5 μm with a 5 mu m peak-to-peak position noise. Then, the sliding mode control (SMC) exhibited a position error of /-5 μm with a 5 μm peak-to-peak position noise.

This work focuses on efficient modelling and adaptive control of friction damping in bladed disks. To efficiently simulate the friction contact, a full-3D time-discrete contact model is reformulated and an analytical expression for the Jacobian matrix is derived that reduces the computation time drastically with respect to the classical finite difference method. The developed numerical solver is applied on bladed disks with shroud contact and the advantage of full-3D contact model compared to a quasi-3D contact model is presented. The developed numerical solver is also applied on bladed disks with strip damper and multiple friction contacts and obtained results are discussed. Furthermore, presence of higher harmonics in the nonlinear contact forces is analyzed and their effect on the excitation of the different nodal diameters of the bladed disk are systematically presented. The main parameters that influence the effectiveness of friction damping in bladed disks are engine excitation order,  contact stiffnesses,  friction coefficient, relative motion at the friction interface and the normal contact load. Due to variation in these parameters during operation, the obtained friction damping in practice may differ from the optimum value. Therefore, to control the normal load adaptively that will lead to an optimum damping in the system despite these variations, use of magnetostrictive actuator is proposed. The magnetostrictive material that develops an internal strain under the influence of an external magnetic field is employed to increase and decrease the normal contact load. A linearized model of the magnetostrictive actuator is used to characterize the magnetoelastic behavior of the actuator.  A nonlinear static contact analysis of the bladed disk reveals that a change of normal load more than 700 N can be achieved using a reasonable size of the actuator. This will give a very good control on friction damping once applied in practice. / <p>QC 20170310</p> / TurboPower

Fiber reinforced composite materials are widely used in aerospace, mechanical, civil and other industries because of their high strength-to-weight and stiffness-to-weight ratios. However, composite structures are highly prone to impact damage. Possible types of defect or damage in composite include matrix cracking, fiber breakage, and delamination between plies. In addition, delamination in a laminated composite is usually invisible. It is very diffcult to detect it while the component is in service and this will eventually lead to catastrophic failure of the structure. Such damages may be caused by dropped tools and ground handling equipments. Damage in a composite structure normally starts as a tiny speckle and gradually grows with the increase in load to some degree. However, when such damage reaches a threshold level, serious accident can occur. Hence, it is important to have up-to-date information on the integrity of the structure to ensure the safety and reliability of composite components, which require frequent inspections to identify and quantify damage that might have occurred even during manufacturing, transportation or storage. How to identify a damage using the obtained information from a damaged composite structure is one of the most pivotal research objectives. Various forms of structural damage cause variations in structural mechanical characteristics, and this property is extensively employed for damage detection. Existing traditional non-destructive inspection techniques utilize a variety of methods such as acoustic emission, C-scan, thermography, shearography and Moir interferometry etc. Each of these techniques is limited in accuracy and applicability. Most of these methods require access to the structure.They also require a significant amount of equipment and expertise to perform inspection. The inspections are typically based on a schedule rather than based on the condition of the structure. Furthermore, the cost associated with these traditional non-destructive techniques can be rather prohibitive. Therefore, there is a need to develop a cost-effective, in-service, diagnostic system for monitoring structural integrity in composite structures. Structural health monitoring techniques based on dynamic response is being used for several years. Changes in lower natural frequencies and mode shapes with their special derivatives or stiffness/ exibility calculation from the measured displacement mode shapes are the most common parameters used in identification of damage. But the sensitivity of these parameters for incipient damage is not satisfactory. On the other hand, for in service structural health monitoring, direct use of structural response histories are more suitable. However, they are very few works reported in the literature on these aspects, especially for composite structures, where higher order modes are the ones that get normally excited due to the presence of flaws. Due to the absence of suitable direct procedure, damage identification from response histories needs inverse mapping; like artificial neural network. But, the main diffculty in such mapping using whole response histories is its high dimensionality. Different general purpose dimension reduction procedures; like principle component analysis or indepen- dent component analysis are available in the literature. As these dimensionally reduced spaces may loose the output uniqueness, which is an essential requirement for neural network mapping, suitable algorithms for extraction of damage signature from these re- sponse histories are not available. Alternatively, fusion of trained networks for different partitioning of the damage space or different number of dimension reduction technique, can overcome this issue efficiently. In addition, coordination of different networks trained with different partitioning for training and testing samples, training algorithms, initial conditions, learning and momentum rates, architectures and sequence of training etc., are some of the factors that improves the mapping efficiency of the networks. The applications of smart materials have drawn much attention in aerospace, civil, mechanical and even bioengineering. The emerging field of smart composite structures offers the promise of truly integrated health and usage monitoring, where a structure can sense and adapt to their environment, loading conditions and operational requirements, and materials can self-repair when damaged. The concept of structural health monitoring using smart materials relies on a network of sensors and actuators integrated with the structure. This area shows great promise as it will be possible to monitor the structural condition of a structure, throughout its service lifetime. Integrating intelligence into the structures using such networks is an interesting field of research in recent years. Some materials that are being used for this purpose include piezoelectric, magnetostrictive and fiber-optic sensors. Structural health monitoring using, piezoelectric or fiber-optic sensors are available in the literature. However, very few works have been reported in the literature on the use of magnetostrictive materials, especially for composite structures. Non contact sensing and actuation with high coupling factor, along with other prop- erties such as large bandwidth and less voltage requirement, make magnetostrictive materials increasingly popular as potential candidates for sensors and actuators in structural health monitoring. Constitutive relationships of magnetostrictive material are represented through two equations, one for actuation and other for sensing, both of which are coupled through magneto-mechanical coefficient. In existing finite element formulation, both the equations are decoupled assuming magnetic field as proportional to the applied current. This assumption neglects the stiffness contribution coming from the coupling between mechanical and magnetic domains, which can cause the response to deviate from the time response. In addition, due to different fabrication and curing difficulties, the actual properties of this material such as magneto-mechanical coupling coefficient or elastic modulus, may differ from results measured at laboratory conditions. Hence, identification of the material properties of these embedded sensor and actuator are essential at their in-situ condition. Although, finite element method still remains most versatile, accurate and generally applicable technique for numerical analysis, the method is computationally expensive for wave propagation analysis of large structures. This is because for accurate prediction, the finite element size should be of the order of the wavelength, which is very small due to high frequency loading. Even in health monitoring studies, when the flaw sizes are very small (of the order of few hundred microns), only higher order modes will get affected. This essentially leads to wave propagation problem. The requirement of cost-effective computation of wave propagation brings us to the necessity of spectral finite element method, which is suitable for the study of wave propagation problems. By virtue of its domain transfer formulation, it bypasses the large system size of finite element method. Further, inverse problem such as force identification problem can be performed most conveniently and efficiently, compared to any other existing methods. In addition, spectral element approach helps us to perform force identification directly from the response histories measured in the sensor. The spectral finite element is used widely for both elementary and higher order one or two dimensional waveguides. Higher order waveguides, normally gives a behavior, where a damping mode (evanescent) will start propagating beyond a certain frequency called the cut-off frequency. Hence, when the loading frequencies are much beyond their corresponding cut-off frequencies, higher order mo des start propagating along the structure and should be considered in the analysis of wave propagations. Based on these considerations, three main goals are identified to be pursued in this thesis. The first is to develop the constitutive relationship for magnetostrictive sensor and actuator suitable for structural analysis. The second is the development of different numerical tools for the modelling the damages. The third is the application of these developed elements towards solving inverse problems such as, material property identification, impact force identification, detection and identification of delamination in composite structure. The thesis consists of four parts spread over six chapters. In the first part, linear, nonlinear, coupled and uncoupled constitutive relationships of magnetostrictive materials are studied and the elastic modulus and magnetostrictive constant are evaluated from the experimental results reported in the literature. In uncoupled model, magnetic field for actuator is considered as coil constant times coil current. The coupled model is studied without assuming any explicit direct relationship with magnetic field. In linear coupled model, the elastic modulus, the permeability and magnetostrictive coupling are assumed as constant. In nonlinear-coupled model, the nonlinearity is decoupled and solved separately for the magnetic domain and mechanical domain using two nonlinear curves,’ namely the stress vs. strain curve and magnetic flux density vs. magnetic field curve. This is done by two different methods. In the first, the magnetic flux density is computed iteratively, while in the second, artificial neural network is used, where a trained network gives the necessary strain and magnetic flux density for a given magnetic field and stress level. In the second part, different finite element formulations for composite structures with embedded magnetostrictive patches, which can act both as sensors and actuators, is studied. Both mechanical and magnetic degrees of freedoms are considered in the formulation. One, two and three-dimensional finite element formulations for both coupled and uncoupled analysis is developed. These developed elements are then used to identify the errors in the overall response of the structure due to uncoupled assumption of the magnetostrictive patches and shown that this error is comparable with the sensitivity of the response due to different damage scenarios. These studies clearly bring out the requirement of coupled analysis for structural health monitoring when magnetostrictive sensor and actuator are used. For the specific cases of beam elements, super convergent finite element formulation for composite beam with embedded magnetostrictive patches is introduced for their specific advantages in having superior convergence and in addition, these elements are free from shear locking. A refined 2-node beam element is derived based on classical and first order shear deformation theory for axial-flexural-shear coupled deformation in asymmetrically stacked laminated composite beams with magnetostrictive patches. The element has an exact shape function matrix, which is derived by exactly solving the static part of the governing equations of motion, where a general ply stacking is considered. This makes the element super convergent for static analysis. The formulated consistent mass matrix, however, is approximate. Since the stiffness is exactly represented, the formulated element predicts natural frequency to greater level of accuracy with smaller discretization compared to other conventional finite elements. Finally, these elements are used for material property identification in conjunction with artificial neural network. In the third part, frequency domain analysis is performed using spectrally formulated beam elements. The formulated elements consider deformation due to both shear and lateral contraction, and numerical experiments are performed to highlight the higher order effects, especially at high frequencies. Spectral element is developed for modelling wave propagation in composite laminate in the presence of magnetostrictive patches. The element, by virtue of its frequency domain formulation, can analyze very large domain with nominal cost of computation and is suitable for studying wave propagation through composite materials. Further more, identification of impact force is performed form the magnetostrictive sensor response histories using these spectral elements. In the last part, different numerical examples for structural health monitoring are directed towards studying the responses due to the presence of the delamination in the structure; and the identification of the delamination from these responses using artificial neural network. Neural network is applied to get structural damage status from the finite element response using its mapping feature, which requires output uniqueness. To overcome the loss of output uniqueness due to the dimension reduction, damage space is divided into different overlapped zones and then different networks are trained for these zones. Committee machine is used to co ordinate among these networks. Next, a five-stage hierarchy of networks is used to consider partitioning of damage space, where different dimension reduction algorithms and different partitioning between training and testing samples are used for better mapping fro the identification procedure. The results of delamination detection for composite laminate show that the method developed in this thesis can be applied to structural damage detection and health monitoring for various industrial structures. This thesis collectively addresses all aspects pertaining to the solution of inverse problem and specially the health monitoring of composite structures using magnetostric tive sensor and actuator. In addition, the thesis discusses the necessity of higher order theory in the high frequency analysis of wavw propagation. The thesis ends with brief summary of the tasks accomplished, significant contribution made to the literature and the future applications where the proposed methods addressed in this thesis can be applied.