Emendas por traspasse são criadas pela justaposição de barras de aço em um determinado comprimento, assegurando que elas se manterão em posição. Assim como em outros sistemas estruturais, a alvenaria estrutural de blocos de concreto utiliza barras de aço como reforço dos elementos quanto à resistência à tração, mais proeminentes em edifícios altos devido à ação dos ventos. As armaduras são projetadas para serem alocados no interior dos blocos, e a prática construtiva no Brasil é posicionar as armaduras de aço antes dos blocos serem assentados. Devido à essa prática, as paredes precisam ser construídas em pelo menos duas etapas, para considerar a altura limite imposta pela armadura posicionada ao operário na elevação dos blocos. Para aumentar a eficiência na elevação das paredes de alvenaria, hélices circulares são propostas como componentes de confinamento do graute que envolve a emenda, permitindo a elevação da parede em etapa única. A armadura é colocada dentro da seção transversal da espiral após a parede de alvenaria ser completamente elevada. O objetivo desta investigação é avaliar a eficiência da emenda por traspasse, com hélice circular atuando como componente do confinamento do graute que envolve a emenda. Quatro configurações de emenda distintas foram ensaiadas: a primeira, referência, foi justaposta e amarrada com arame; a segunda foi espaçada, porém sem a presença de um componente de confinamento; a terceira foi espaçada e continha uma hélice circular com passo de 3,5 cm; e a quarta foi espaçada e continha uma hélice circular com passo de 8,0 cm. Os ensaios permitiram concluir que a hélice de traspasse é um componente eficiente no confinamento das emendas por traspasse em alvenaria estrutural de blocos de concreto. Análises estatísticas dos resultados demonstram que emendas por a emenda com hélice circular de 3,5 cm não só é equivalente à emenda por referência do ponto de vista da resistência à tração, como também contribui para a redução de fissuras. / Lap slices are created by the overlapping of reinforcement bars over a specified length and reassuring that they stay in place. As with other structural systems, concrete block masonry uses reinforcing steel to carry the tensile loads which are more prominent on tall buildings due to the effect of wind. Reinforcing bars are designed to be placed inside block cells. The construction practice in Brazil is to place the reinforcing steel before the block units are laid. With this practice, walls need to be built in at least two lifts to account for the height limits imposed by the mason having to lift each block over the reinforcing bars. To increase the efficiency of wall construction, spirals are proposed as confinement components of the grout surrounding the lap splices, allowing a single-lift wall construction. The vertical reinforcement is then placed inside the cross-section of the spiral after the laying of blocks is complete. The objective of this investigation is to evaluate the efficiency of lap splices with spirals as confinement components of grout. Four types of single-bar splice specimens were prepared during the test program consisting of: first, contact lap splices tied by steel lock wires; second, non-contact lap splices without any confinement components; third, non-contact lap splices with the surrounding grout confined by spirals with 35 mm pitch; fourth, non-contact lap splices with the surrounding grout confined by spirals with 80 mm pitch. The results of the experimental program show that spirals are efficient confinement components of non-contact lap splices in concrete block masonry. Statistical analysis of results demonstrate that non-contact lap splices confined by spirals with 35 mm pitch are not only equivalent with contact lap splices regarding their ultimate tensile resistance, but also contribute to the reduction of cracks.

A large inventory of low rise masonry buildings in Canada and elsewhere in the world were built using unreinforced or partially reinforced load bearing wall. The majority of existing masonry structures is deficient in resisting seismic force demands specified in current building codes. Therefore, they pose significant risk to life safety and economic wellbeing of any major metropolitan centre. Because it is not economically feasible to replace the existing substandard buildings with new and improved structures, seismic retrofitting remains to be an economically viable option. The effectiveness of surface bonded carbon fiber-reinforced polymer (CFRP) sheets in retrofitting low-rise load bearing masonry walls was investigated in the current research project. The retrofit technique included the enhancements in wall capacity in shear and flexure, as well as anchoring the walls to the supporting elements through appropriate anchorage systems. Both FRP fan type anchors and steel sheet anchors were investigated for elastic and inelastic wall response. One partially reinforced masonry (PRM) wall and one unreinforced masonry (URM) wall were built, instrumented and tested under simulated seismic loading to develop the retrofit technique. The walls were retrofitted with CFRP sheets applied only on one side to represent a frequently encountered constraint in practice. FRP fan anchors and stainless steel sheet anchors were used to connect the vertical FRP sheets to the wall foundation. The walls were tested under constant gravity load and incrementally increasing in-plane deformation reversals. The lateral load capacities of both walls were enhanced significantly. The steel sheet anchors also resulted in some ductility. In addition, some small-scale tests were performed to select appropriate anchor materials. It was concluded that ductile stainless steel sheet anchors would be the best option for brittle URM walls. Analytical research was conducted to assess the applicability of truss analogy to retrofitted walls. An analytical model was developed and load displacement relationships were generated for the two walls that were retrofitted. The analytical results were compared with those obtained experimentally, indicating good agreement in force resistance for use as a design tool.

Mit der vorliegenden Arbeit wurde ein Beitrag zur Klärung des Querkrafttragverhaltens von Wandscheiben im Mauerwerksbau geleistet. Die Untersuchungen umfassten hierbei analytische, numerische und versuchstechnische Betrachtungen. Als Grundlage für die Untersuchungen wurden FE-Elemente und FE Materialroutinen, die auf die Materialspezifik des Mauerwerks abgestimmt sind, entwickelt und in das Programmsystem ANSYS implementiert. Als wesentliche Eingangsgrößen sowohl für die analytischen als auch die numerischen Berechnungen werden diverse Materialparameter benötigt. Neben den üblichen Materialversuchen sind weiterführende Betrachtungen zu den „Kleinversuchen“ angestellt worden. Für einige Materialparameter waren numerische Rückrechnungen, wie z.B. für die Keilspaltversuche, erforderlich. Für ein breites Spektrum an Materialien, angefangen beim Ziegel über Mörtel bis zum Lehm, konnten wesentliche Werte ermittelt werden. Die vorhandenen analytischen Modelle der Schubfestigkeit wurden im Rahmen der vorgelegten Arbeit weiterentwickelt. Nach der Herleitung neuer Gleichungen galt es, diese für die Anwendung zu vereinfachen. Es sind auch numerische Modelle erläutert, die einen minimierten Wandausschnitt darstellen und mit denen eine direkte Berechnung der Schubfestigkeit möglich ist. Neben der Schubfestigkeit des Mauerwerks haben auch die Wandgeometrie und die Einbindung der Wand in das Gebäude Einfluss auf die maßgebende Querkrafttragfähigkeit. Zu deren Berücksichtigung werden wiederum Ingenieurmodelle benötigt, deren Komponenten hier eingehender betrachtet wurden. Als Grundlage dienten weitere Versuche basierend auf dem Modell der Aussteifungswand im Gebäude. Sowohl aus den analytisch gewonnenen Gleichungen als auch aus den an den Versuchen kalibrierten Gleichungen sind Lösungen für die Normung entwickelt worden. Diese beinhalten neben Gleichungen für das genaue Verfahren auch stark vereinfachte Bemessungslösungen mit tabellarisch aufbereiteten Mindestquerschnitten für die Aussteifungswände.

Diploma thesis The complex diagnostics of bricked bridge construction is in the theoretical part focused on the summary of regulations of road and railway bridges. In the practical part was conducted the inspection and diagnostic survey of the railway viaduct on Křenová, near the main train station Brno.

One of the most widespread causes of building deterioration is high moisture, which in extreme cases may even arrive as floods. The action of high moisture in a structure often results in damage or alteration of properties, but it can be mitigated with various protective measures, most commonly waterproofing. However, the efficacy of waterproofing depends of flawless implementation. Another effective form of protection against high moisture is the correct choice of location, but the number of suitable construction plots is rapidly decreasing or their price is too high. This is why new construction, particularly family homes, now occurs even in locations known for the increased risk of high moisture. This doctoral thesis focuses on the research and development of the most common masonry systems with structural clay tiles designed to withstand application in flood areas thanks to the special properties of the individual elements, components, and the system as a whole.

Terrorism has become a serious threat in the world, with bomb attacks carried out both inside and outside buildings. There are already many unreinforced masonry buildings in existence, and some of them are historical buildings. However, they do not perform well under blast loading. Aiming on protecting masonry buildings, retrofitting techniques were developed. Some experimental work on studying the effect of retrofitted URM walls has been done in recent years; however, these tests usually cost a significant amount of time and funds. Because of this, numerical simulation has become a good alternative, and can be used to study the behaviour of masonry structures, and predict the outcomes of experimental tests. This project was carried out to find efficient retrofitting technique under blast loading by developing numerical material models. It was based on experimental research of strengthening URM walls by using retrofitting technologies under out-of-plane loading at the University of Adelaide. The numerical models can be applied to study large-scaled structures under static loading, and the research work is then extended to the field of blast loading. Aiming on deriving efficient material models, homogenization technology was introduced to this research. Fifty cases of numerical analysis on masonry basic cell were conducted to derive equivalent orthotropic material properties. To study the increasing capability in strength and ductility of retrofitted URM walls, pull-tests were simulated using interface element model to investigate the bond-slip relationship of FRP plates bonded to masonry blocks. The interface element model was then used to simulate performance of retrofitted URM walls under static loads. The accuracy of the numerical results was verified by comparing with the experimental results from previous tests at the University of Adelaide by Griffith et al. (2007) on unreinforced masonry walls and by Yang (2007) on FRP retrofitted masonry walls. To study the de-bonding behaviours of retrofits bonded to masonry, and find appropriate solution to protect certain masonry walls against blast loading, various retrofitting technologies were examined. The simulation covers explosive impacts of a wide range of impulses. Based on this work, pressure-impulse diagrams for different types of retrofitted URM walls were developed as a design guideline for estimating the blast effect on retrofitted masonry walls. The outcomes of this research will contribute to the development of numerical simulation on modelling retrofitted URM walls, improving the technique for explosion-resistant of masonry buildings, and providing a type of guideline for blast-resistant design. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1349719 / Thesis (M.Eng.Sc.) - University of Adelaide, School of Civil, Environmental and Mining Engineering, 2009

Terrorism has become a serious threat in the world, with bomb attacks carried out both inside and outside buildings. There are already many unreinforced masonry buildings in existence, and some of them are historical buildings. However, they do not perform well under blast loading. Aiming on protecting masonry buildings, retrofitting techniques were developed. Some experimental work on studying the effect of retrofitted URM walls has been done in recent years; however, these tests usually cost a significant amount of time and funds. Because of this, numerical simulation has become a good alternative, and can be used to study the behaviour of masonry structures, and predict the outcomes of experimental tests. This project was carried out to find efficient retrofitting technique under blast loading by developing numerical material models. It was based on experimental research of strengthening URM walls by using retrofitting technologies under out-of-plane loading at the University of Adelaide. The numerical models can be applied to study large-scaled structures under static loading, and the research work is then extended to the field of blast loading. Aiming on deriving efficient material models, homogenization technology was introduced to this research. Fifty cases of numerical analysis on masonry basic cell were conducted to derive equivalent orthotropic material properties. To study the increasing capability in strength and ductility of retrofitted URM walls, pull-tests were simulated using interface element model to investigate the bond-slip relationship of FRP plates bonded to masonry blocks. The interface element model was then used to simulate performance of retrofitted URM walls under static loads. The accuracy of the numerical results was verified by comparing with the experimental results from previous tests at the University of Adelaide by Griffith et al. (2007) on unreinforced masonry walls and by Yang (2007) on FRP retrofitted masonry walls. To study the de-bonding behaviours of retrofits bonded to masonry, and find appropriate solution to protect certain masonry walls against blast loading, various retrofitting technologies were examined. The simulation covers explosive impacts of a wide range of impulses. Based on this work, pressure-impulse diagrams for different types of retrofitted URM walls were developed as a design guideline for estimating the blast effect on retrofitted masonry walls. The outcomes of this research will contribute to the development of numerical simulation on modelling retrofitted URM walls, improving the technique for explosion-resistant of masonry buildings, and providing a type of guideline for blast-resistant design. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1349719 / Thesis (M.Eng.Sc.) - University of Adelaide, School of Civil, Environmental and Mining Engineering, 2009

Terrorism has become a serious threat in the world, with bomb attacks carried out both inside and outside buildings. There are already many unreinforced masonry buildings in existence, and some of them are historical buildings. However, they do not perform well under blast loading. Aiming on protecting masonry buildings, retrofitting techniques were developed. Some experimental work on studying the effect of retrofitted URM walls has been done in recent years; however, these tests usually cost a significant amount of time and funds. Because of this, numerical simulation has become a good alternative, and can be used to study the behaviour of masonry structures, and predict the outcomes of experimental tests. This project was carried out to find efficient retrofitting technique under blast loading by developing numerical material models. It was based on experimental research of strengthening URM walls by using retrofitting technologies under out-of-plane loading at the University of Adelaide. The numerical models can be applied to study large-scaled structures under static loading, and the research work is then extended to the field of blast loading. Aiming on deriving efficient material models, homogenization technology was introduced to this research. Fifty cases of numerical analysis on masonry basic cell were conducted to derive equivalent orthotropic material properties. To study the increasing capability in strength and ductility of retrofitted URM walls, pull-tests were simulated using interface element model to investigate the bond-slip relationship of FRP plates bonded to masonry blocks. The interface element model was then used to simulate performance of retrofitted URM walls under static loads. The accuracy of the numerical results was verified by comparing with the experimental results from previous tests at the University of Adelaide by Griffith et al. (2007) on unreinforced masonry walls and by Yang (2007) on FRP retrofitted masonry walls. To study the de-bonding behaviours of retrofits bonded to masonry, and find appropriate solution to protect certain masonry walls against blast loading, various retrofitting technologies were examined. The simulation covers explosive impacts of a wide range of impulses. Based on this work, pressure-impulse diagrams for different types of retrofitted URM walls were developed as a design guideline for estimating the blast effect on retrofitted masonry walls. The outcomes of this research will contribute to the development of numerical simulation on modelling retrofitted URM walls, improving the technique for explosion-resistant of masonry buildings, and providing a type of guideline for blast-resistant design. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1349719 / Thesis (M.Eng.Sc.) - University of Adelaide, School of Civil, Environmental and Mining Engineering, 2009

Masonry construction is labor-intensive. Processes involve little to no mechanization and require a large number of crews made up of workers with diverse skills, capabilities, and personalities. Relationships among crews are tight and very dependent. Often crews are re-assembled and the superintendent is responsible for assigning workers to crews and allocating crews to different tasks to maximize workflow. This dynamic environment can influence the motivation of workers and impose pressure and stress on them. Workers, unlike other resources, have their own needs and requirements beyond the financial compensation for their work. Workers place a great value on requirements such as certainty about work assignments, matching assignments to career development goals, and work satisfaction. If managed properly, workers may bring considerable benefits to both the project and the contractor. A project that links workers to career goals not only allows contractors to develop more qualified staff for its future projects, but also gives the worker opportunities for career growth and development. Additionally, job satisfaction and efficiency increases from suitable worker assignment and consideration of tasks. Therefore, the study of sustainable labor management practices is of interest in masonry construction and other labor-intensive industries. A mixed-integer programming (MIP) model enables the integration of workers needs and contractor requirements into the process of labor allocation. Furthermore, the model can be used to quantify strategies that maximize productivity, quality of work, and the well-being of workers. Developing such a model is a necessary task. To plan and manage masonry construction, the contractor has to take into account not only multiple workers with different characteristics but also rules for crew design and makeup and project requirements in terms of personnel needs. Providing an analytical description of all the needs and requirements is challenging. Therefore, to determine labor management practices that indeed maximize production and maximize workers satisfaction, the model needs to realistically represent the realities in masonry construction sites and staffing practices, while remaining computationally manageable such that optimization models can be derived. This dissertation proposes a decision support system (DSS) for sustainable labor management in masonry construction that takes into consideration information on workers and job characteristics with the intention of assisting decision makers in allocating crews. Firstly, semi-structured interviews were conducted with masonry practitioners to gather perspectives on labor requirements, rules for crew design, and drivers for crew makeup. Secondly, a model that incorporates realities was implemented. The model supports masonry contractors and superintendent in the challenging process of managing crews, that is, to determine the composition of each crew and the allocation of crews to maximize productivity and workflow while considering workers’ preferences and well-being. With the DSS, project managers and superintendents are not only able to identify working patterns for each of the workers but also optimal crew formation and investment and labor costs. Data from real case study is used to compare the schedule and allocation on the site with the one proposed by the model. The comparison shows the model can optimize the allocation of crews to reduce the completion time to build the walls while maximizing the utilization of masons and outlining opportunities for concurrent work. It is expected that the DSS will help contractors improve productivity and quality while efficiently managing masonry workers in a more sustainable way. The contributions for the masonry industry are two-fold. Firstly, the proposed model considers a set of rules that masonry practitioners typically use to design crews of masons and analytically captures the realities of masonry construction jobsites when managing labor. Secondly, it attempts to quantify and mathematically model the practices that contractors use for crew makeup and evaluate labor management allocation both in terms of contractor requirements and worker needs. Literature review indicates that the existing models for labor allocation have not taken into consideration masonry site realities. An optimization framework, which combines masonry site realities from the semi-structured interviews is proposed. The framework results in a MIP model that is used to solve a crew scheduling and allocation problem. The model is formulated to determine which masons are in a crew and to assign crews to the different walls in a project. Additionally, it is used to evaluate crew design strategies that maximize productivity.

<p align="justify">The conservation of structures of the historical heritage is an increasing concern nowadays for public authorities. The technical design phase of repair operations for these structures is of prime importance. Such operations usually require an estimation of the residual strength and of the potential structural failure modes of structures to optimize the choice of the repairing techniques.</p> <p align="justify">Although rules of thumb and codes are widely used, numerical simulations now start to emerge as valuable tools. Such alternative methods may be useful in this respect only if they are able to account realistically for the possibly complex failure modes of masonry in structural applications.</p> <p align="justify">The mechanical behaviour of masonry is characterized by the properties of its constituents (bricks and mortar joints) and their stacking mode. Structural failure mechanisms are strongly connected to the mesostructure of the material, with strong localization and damage-induced anisotropy.</p> <p align="justify">The currently available numerical tools for this material are mostly based on approaches incorporating only one scale of representation. Mesoscopic models are used in order to study structural details with an explicit representation of the constituents and of their behaviour. The range of applicability of these descriptions is however restricted by computational costs. At the other end of the spectrum, macroscopic descriptions used in structural computations rely on phenomenological constitutive laws representing the collective behaviour of the constituents. As a result, these macroscopic models are difficult to identify and sometimes lead to wrong failure mode predictions.</p> <p align="justify">The purpose of this study is to bridge the gap between mesoscopic and macroscopic representations and to propose a computational methodology for the analysis of plane masonry walls. To overcome the drawbacks of existing approaches, a multi-scale framework is used which allows to include mesoscopic behaviour features in macroscopic descriptions, without the need for an a priori postulated macroscopic constitutive law. First, a mesoscopic constitutive description is defined for the quasi-brittle constituents of the masonry material, the failure of which mainly occurs through stiffness degradation. The mesoscopic description is therefore based on a scalar damage model. Plane stress and generalized plane state assumptions are used at the mesoscopic scale, leading to two-dimensional macroscopic continuum descriptions. Based on periodic homogenization techniques and unit cell computations, it is shown that the identified mesoscopic constitutive setting allows to reproduce the characteristic shape of (anisotropic) failure envelopes observed experimentally. The failure modes corresponding to various macroscopic loading directions are also shown to be correctly captured. The in-plane failure mechanisms are correctly represented by a plane stress description, while the generalized plane state assumption, introducing simplified three-dimensional effects, is shown to be needed to represent out-of-plane failure under biaxial compressive loading. Macroscopic damage-induced anisotropy resulting from the constituents' stacking mode in the material, which is complex to represent properly using macroscopic phenomenological constitutive equations, is here obtained in a natural fashion. The identified mesoscopic description is introduced in a scale transition procedure to infer the macroscopic response of the material. The first-order computational homogenization technique is used for this purpose to extract this response from unit cells. Damage localization eventually appears as a natural outcome of the quasi-brittle nature of the constituents. The onset of macroscopic localization is treated as a material bifurcation phenomenon and is detected from an eigenvalue analysis of the homogenized acoustic tensor obtained from the scale transition procedure together with a limit point criterion. The macroscopic localization orientations obtained with this type of detection are shown to be strongly related to the underlying mesostructural failure modes in the unit cells.</p> <p align="justify">A well-posed macroscopic description is preserved by embedding localization bands at the macroscopic localization onset, with a width directly deduced from the initial periodicity of the mesostructure of the material. This allows to take into account the finite size of the fracturing zone in the macroscopic description. As a result of mesoscopic damage localization in narrow zones of the order of a mortar joint, the material response computationally deduced from unit cells may exhibit a snap-back behaviour. This precludes the use of such a response in the standard strain-driven multi-scale scheme.</p> <p align="justify">Adaptations of the multi-scale framework required to treat the mesostructural response snap-back are proposed. This multi-scale framework is finally applied for a typical confined shear wall problem, which allows to verify its ability to represent complex structural failure modes.</p>