1 |
Synthesis and characterization of substituted dithiocarbamates ligands and complexes as a source of metal (Pb, Ni & Co) sulphide nanoparticlesThangwane, Selaelo Christabel January 2017 (has links)
M. Tech. (Department of Chemistry, Faculty of Applied and Computer Sciences), Vaal University of Technology. / Lead, nickel and cobalt dithiocarbamates complexes were synthesized using methanol and water as solvents. All complexes were refluxed at 60 °C, cooled at room temperature, washed with methanol to remove the impurities and dried under the fume hood. A combination of Fourier transformer infrared (FTIR), elemental analysis (EA) and thermogravimetric analysis (TGA) were used to characterize these complexes. There was shifting of bands from low to high frequencies of the dithiocarbamates complexes compared to benzimidazole derivatives. The absence of the N-H band and the presence of new C=S bands confirmed that the complexes can be used in the preparation of metal sulphide nanoparticles. Elemental analysis showed that there was a percentage mismatch for the complexes I, III, IV and V. Complexes II and VI calculated percentages were within the limits with the found percentages except for sulphur which was low. The TGA curves decomposed to form a mixture of metal and metal sulphides for complex I, II, III and IV except for complex VI which gave metal sulphide only. All benzimidazole complexes decomposed at higher temperatures and were considered as stable complexes.
Lead sulphide (PbS) is an important group IV-VI metal chalcogenide semiconductor. It has a direct narrow band gap of 0.41 eV at 300K and a large excitonic Bohr radius of 18 nm. Lead sulphide absorption band can be tuned to anywhere between near IR to UV (0.4μm) covering the entire visible spectrum, while achieving the quantum confinement region. The synthesis of lead sulphide nanoparticles was conducted by varying the effect of the reaction conditions such as the type of capping agents and temperature. Lead dithiocarbamate complex derived from benzimidazole, [Pb(S2N2C8H5)2] was thermolysed in hexadecylamine (HDA) and trioctylphosphine oxide (TOPO) at different reaction temperatures (140, 160 and 180 °C) to produce HDA and TOPO capped PbS nanoparticles. The nanoparticles were characterized using X-ray diffraction (XRD) for structural analysis, transmission electron microscopy (TEM) for shape and size, Ultraviolet visible (UV/Vis) and Photoluminescence (PL) spectroscopy for optical properties. An increase in temperature gave a decrease in the sizes of the nanoparticles when using the HDA capped lead benzimidazole dithiocarbamate complex. The observed morphology was cubes. TOPO capped lead benzimidazole dithiocarbamate complex gave no specific trend when temperature was varied. A cross-like layer with quasi spherical particles on top was observed at 160 °C. At 180 °C, the cross-like layer decomposed into rods- like materials with quasi spherical particles on top for TOPO capped PbS nanoparticles. For lead 2-methylbenzimidazole [Pb(S2N2C9H7)2] dithiocarbamate complex, TOPO capped PbS produced agglomerated cubic morphology at low temperature but as the temperature was increased agglomerated cylindrical shapes were observed. HDA capped PbS produced polydispersed nanocubes which were increasing in size when the temperature was increased. Nanoparticles displayed a blue shift in band edges with good photoluminescence behaviour which was red shifted from their respective band edges all temperatures and capping agents. XRD confirmed the crystal structure of cubic phase (galena) of PbS at all temperatures except for HDA capped PbS nanoparticles at 140 °C from lead benzimidazole dithiocarbamate complex which confirmed the crystal structure of face-centred cubic phase of PbS nanoparticles.
Nickel sulphide has much more complicated phase diagram than cobalt sulfides and iron sulfides. Their chemical composition has many crystalline phases such as α-NiS, β=NiS, NiS2, Ni3S2, Ni3S4, Ni7S6 and Ni9S8. Ni3S2 phase has shown potential as a low-cost counter electrode material in dye sensitised solar cells, while the α-NiS phase has been applied as a cathode Material in lithium-ion batteries. The synthesis of nickel sulphide nanoparticles was done by varying the effect of the reaction conditions such concentration and temperature. Nickel benzimidazole dithiocarbamate [Ni(S2N2C8H5)2] and nickel 2-methylbenzimidazole [Ni (S2N2C9H7)2] dithiocarbamates complexes were thermolysed in hexadecylamine (HDA) at different reaction temperatures (140, 160 and 180 °C) and precursor concentrations (0.30, 0.35 and 0.40 g) to produce HDA capped NiS nanoparticles. It was observed that increasing both temperature and precursor concentration increased the size of the nanoparticles. Anisotropic particles were observed for both complexes when varying precursor concentration and temperature. Nickel benzimidazole dithiocarbamate complex produced stable shapes (spheres and cubes) of nickel sulphide nanoparticles. Nickel 2-methylbenzimidazole dithiocarbamate complex produced a mixture of spheres, cubes, triangles and rods nickel sulphide nanoparticles at all concentrations. But when varying temperature, it only produced that mixture at 160 °C. The optical measurements supported the presence of smaller particles at all temperatures and concentrations. XRD showed the presence of C7OS8 and pure nickel as impurities. However, the crystal structure of cubic Ni3S4 was observed at low temperatures and an introduction of monoclinic NixS6 at high temperature (180 °C) when varying temperature for both complexes. When varying concentration using nickel benzimidazole dithiocarbamate complex, XRD showed the presence of NiSO4.6H2O impurities at high temperatures. At 160 °C a mixture of hexagonal NiS and cubic Ni3S4 was observed. At low temperatures only nickel as a metal was found as an impurity and the crystal structure of cubic Ni3S4 was observed. When nickel 2-methylbenzimidazole complex was used, C7OS8 and pure nickel were found as impurities but the crystal structure of cubic Ni3S4 was observed.
Cobalt sulphide (CoS) belongs to the family of group II-IV compounds with considerable potential for application in electronic devices. They have a complex phase diagram and their chemical composition have many phases such as Co4S3, Co9S8, CoS, Co1-xS, Co3S4, Co2S3 and CoS2. The synthesis of cobalt sulphide nanoparticles was conducted by varying the effect of temperature on size and shape of the nanoparticles. Nickel benzimidazole dithiocarbamate, [Ni(S2N2C8H5)2] and nickel 2-methylbenzimidazole [Ni(S2N2C9H7)2] complexes were thermolysed in hexadecylamine (HDA) at different reaction temperatures (140, 160 and 180 °C) to produce HDA capped CoS nanoparticles. Cobalt benzimidazole dithiocarbamate complex produced close to spherical shapes nanoparticles at all temperatures. The images showed that as temperature was increased, the size of the particles decreased. All the main reflection peaks were indexed to face-centred cubic Co3S4 and there were some impurities of C7OS8 at all temperatures. The optical measurements supported the presence of smaller particles at all temperatures. Cobalt 2-methylbenzimidazole dithiocarbamate complex produced big and undefined morphology. The optical properties were also featureless and XRD only showed impurities of C7OS8. The impurity is thought to be generated from a side reaction between benzimidazole and carbon disulphide to give this persistent organic moiety.
|
2 |
Synthesis and characterization of water soluble sugar-capped metal sulphide semiconductor nanoparticles and their toxicityShumbula, Poslet Morgan 14 September 2011 (has links)
Ph. D., Faculty of Science, University of the Witwatersrand, 2011 / Different cadmium, cobalt and zinc complexes of substituted thioureas, dithiocarbamates and thiuram di/monosulfides were synthesized using ethanol or water as solvents. The synthesis of dithiocarbamates complexes were performed at room temperature while the rest were refluxed at 70 oC. The complexes were easy to synthesize, of low cost and stable in air and were obtained in good yields. The complexes were characterized using various instruments, such as infrared (FT-IR) and proton nuclear magnetic resonance (1H NMR) spectroscopy, elemental analyzer, thermogravimetric analysis (TGA) and X-ray crystallography. The complexes were found to coordinate the ligands through sulphur atom, instead of nitrogen atom. This was concluded after shifts to higher or lower wavenumbers were observed from the infrared spectra of the complexes as compared to their free ligands. The 1H NMR also depicted formation of the complexes, with complexes peaks shifting to downfield as compared to the free ligands. There were also signs of broad NH peaks especially for substituted thiourea complexes. The crystals grown from complex II (diphenylthiourea cadmium complex) depicted a tetrahedral geometry, with two sulphur and two chlorine atoms binding to the central atom which is cadmium. The easily synthesized complexes were thermolysed in HDA, TOPO or a mixture of the two to form metal sulphide nanoparticles. The role of the above capping agents or ligands was to control particles growth and prevent them from aggregation. A single source precursor route was employed in synthesizing hydrophobic semiconductor nanoparticles, which are also known as (QDs) quantum dots. Various shapes, which are rods (mono-, bi- and tripods), spheres and hexagonal were revealed through transmission electron microscope (TEM). The sizes of these particles ranged from 1 to 12 nm in diameter. Other instruments used for characterising the as-synthesized semiconductor nanoparticles include X-ray diffractometer (XRD), UV-Visible and Photoluminescence spectroscopy. The optical properties of the particles as determined by the UV-Visible spectroscopy revealed some differences as compared to the bulk materials. All the absorption spectra were blue shifted to the bulk materials signifying finite size of the particles. The XRD peaks observed were broad as compared to the bulk ones, which also signified small particles size. Two phases, which are hexagonal and cubic, were revealed from the XRD.
viii
The hydrophobic semiconductor nanoparticles or quantum dots synthesized were then transferred into water soluble using ligand exchange method. The chloroform and pyridine routes were used to synthesize hydrophilic semiconductor nanoparticles, with pyridine route being preferred. The shape and size of the particles were not influenced by the transfer into water soluble since the experiments were performed at room temperature. This was confirmed by TEM analysis. The capping agents used after displacing water insoluble capping agents were sugars, which were soluble in water. The XRD pattern of the semiconductor nanoparticles/QDs (CdS) capped by sugars after ligand exchange through pyridine yielded multiple peaks which were difficult to assign. The attempt to employ ligand exchange method in transferring hydrophobic CoxSy and ZnS nanoparticles to hydrophilic CoxSy and ZnS nanoparticles proved unsuccessful. When the materials were centrifuged after the sugars were introduced as capping agents, some solid material settled at the bottom, with some floating on top of the solution. This was an indication that the materials were not miscible.
The hydrophilic CdS, CoxSy and ZnS nanoparticles were also synthesized using direct method. In this method, the metal sources and capping (sugars) were dissolved in ethylene glycol at 100 oC. The sulphur sources were also dissolved separately in the same solvent. Upon completion, the latter solution was added to the former one. The particles were grown at 160 oC for an hour with ethylene glycol as a solvent. The morphology of the particles dominated through this method was spherical-like in shape. The crystallinity of CdS and ZnS nanoparticles depicted hexagonal and cubic phases depending on the complexes used. The XRD indicated the armophous nature of the cobalt sulphide nanoparticles, irrespective of the precursor used.
Due to the toxicity problem of the quantum dots, especially CdS, the water soluble CdS capped by glucuronic acid, glucose and sucrose after ligand exchange were chosen for that study. However, results showed that the CdS used were not toxic. It was measured or deduced by checking the viability which remained above 90%. Add a bit of deductions about toxicity study here, just some of the general trends.
|
3 |
Measurement of surface tension in base metal sulphide mattes by an improved sessile drop methodHamuyuni, Joseph 12 1900 (has links)
Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: See item for full text / AFRIKAANSE OPSOMMING: Sien item vir volteks
|
4 |
Tracing on-axis diffuse fluids by chalcophile elements distribution in upper oceanic crust at Pito Deep, East Pacific RiseTian, Zhu 29 November 2016 (has links)
Mid-ocean ridge hydrothermal systems play an important role in the cycling of energy and mass between the solid earth and oceans. The on-axis low-temperature diffuse fluids (temperature lower than ~100 °C) carry ~90% of the on-axis heat fluxes, but diffuse fluids generation is poorly constrained. This study uses the abundance of the chalcophile elements, which form metal-sulphides in the rock record, to test models for diffuse fluids generation. These include mixing between seawater and high-temperature hydrothermal fluids and conductive cooling of high- temperature hydrothermal fluids.
This thesis determined the concentrations of the elements of interest (As, Mo, Ag, Cd, Sn, and Tl) in geological reference materials using standard addition method in ICP-MS. These values were used to calibrate the analysis of samples from Pito Deep to trace the abundance of these elements within the upper oceanic crust. The results show that the Zn, Cu, As, Ag, Cd, Tl, and Pb are generally depleted in sheeted dikes and enriched in the lava unit and/or the transition zone, which is consistent with previous studies on fast-spreading EPR crust at Hole 504B, Hess Deep and Hole 1256D. The enrichment of these elements in the lava unit and/or the transition zone suggests that cooling high-temperature hydrothermal fluids to form diffuse fluids occurred in this
iii
iv area of the oceanic crust. Molybdenum and Sb are added into all units of the crust by
recharging seawater. The concentrations of chalcophile elements in diffuse fluids were calculated by a mass balance. The results of this study favored a diffuse fluids generation model that involves mixing of seawater and high-temperature hydrothermal fluids. Results also show that the observed concentrations of Mo and Sb requires extra input source besides recharging seawater and oceanic crust, possibly particulates in seawater. / Graduate / juliatian2013@gmail.com
|
5 |
Long-term metal retention processes in a peat bog : Field studies, data and modellingSyrovetnik, Kristina January 2005 (has links)
The study was inspired by the need to assess long-term metal retention in municipal solid waste (MSW) landfills. The long-term processes in landfills are poorly known due to the relatively short time that such landfills have been in existence. Natural analogues where similar metal binding processes could be expected were therefore sought for. The work described in this thesis aims to elucidate the long-term transport and attenuation processes involved in the retention of heavy metals in a peat bog, through field studies and modelling. The Oostriku peat bog (central Estonia) has been exposed to metal-rich groundwater discharge over a long period of time and was found to have accumulated high concentrations of Fe, other heavy metals (e.g. Pb, Cu, Zn, Mn), and As. It was characterised in detail with respect to metal depth distribution and main metal binding mechanisms (using an optimised Tessier extraction scheme). The oxidation of metal sulphides in the surrounding carbonate bedrock was proposed to be a possible long-term source of heavy metals in the water emerging in a spring at the peat site. The water in the spring and peat pore-water was sampled and analysed. The dissolution sequence of the sulphide minerals and evolution of the water composition along a flowpath in the carbonate rock were modelled. Resulting aqueous phase concentration of major and minor elements are discussed in relation to governing geochemical processes. The simulated water composition was compared with that observed. Retention of metals transported with water through the peat was assessed through modelling equilibrium sorption on solid organic matter and amorphous ferric oxyhydroxide by using a simplified quantitative modelling approach and independently obtained data. Dynamic evolution of metal sorption fronts along a peat profile over time was modelled to test metal-metal competition effects. A possible formation of ferric oxyhydroxide in the peat bog was also assessed with the model. / QC 20101001
|
6 |
In-situ Removal of Hydrogen Sulphide from Landfill Gas : Arising from the Interaction between Municipal Solid Waste and Sulphide Mine Environments within Bioreactor ConditionsLazarevic, David Andrew January 2007 (has links)
This project was compiled in co-operation with the Royal Institute of Technology, Stockholm and Veolia Environmental Services (Australia) at the Woodlawn Bioreactor in NSW, Australia. Hydrogen sulphide is an unwanted component of landfill gas, raising occupational health and safety concerns, whilst leading to acid gas corrosion of power generation equipment and increased emissions of SOx, a primary constituent of acidification. Australian governmental requirements to place a periodic cover over the unused proportion of the tipping surface of landfills and bioreactors create an interesting opportunity for the removal of the hydrogen sulphide component of landfill gas. Using waste materials containing a high concentration of metals as waste cover can enhance the precipitation of sulphur in the form of metal sulphides. The reduction of sulphate via sulphate reducing bacteria is prevalent in sites that have a sizeable inflow of sulphate. The Woodlawn Bioreactor is located in an area where the influence of sulphate has a critical influence of bioreactor performance and production of hydrogen sulphide. Through a series of experimental bioreactors it was established that from the use of metalliferous periodic waste covers, the hydrogen sulphide component of landfill gas was maintained at an extremely low level when compared to the levels of hydrogen sulphide produced in waste under the influence of high sulphate loads with no waste cover. / www.ima.kth.se
|
7 |
Activité et stabilité de phases sulfures pour l’hydrotraitement d’huiles végétales / Activity and stability of sulfur catalytic phases for hydrotreating of vegetable oilsRuinart de Brimont, Mathias 13 October 2011 (has links)
En combinant expérimentations et calculs ab initio, nous proposons une étude rationnelle des mécanismes de désoxygénation de molécules modèles pertinentes (heptanoate d'éthyle et heptanal) afin de fournir des guides pour définir des systèmes catalytiques optimaux pour l'hydrotraitement de matières premières renouvelables (huiles végétales, graisses animales). L'hydrotraitement d'huiles végétales, par la réaction de désoxygénation, est une voie alternative à la transestérification et peut être envisagée pour obtenir une base gazole de haute qualité. La transformation des composés oxygénés modèles a été étudiée sous une pression totale de 1.5 MPa, à une température de 523 K, dans un réacteur à lit fixe en présence de différents sulfures de métaux de transition massiques (SMT). Cette étude a mis en évidence l'influence de la nature phase sulfure sur la sélectivité des voies de désoxygénation (hydrodésoxygénation (HDO) et/ou décarbonylation/ décarboxylation (DCO)) ainsi que la réactivité particulière du sulfure de rhodium lors de la transformation de l'heptanoate d'éthyle. À l'inverse, quelle que soit la phase sulfure utilisée, la transformation de l'heptanal suit principalement la voie HDO. Dans nos conditions réactionnelles, l'heptanal a été identifié comme un intermédiaire de cette voie de désoxygénation. L'effet promoteur du cobalt et du nickel sur l'activité du sulfure de molybdène monométallique a été observé lors de la transformation de l'heptanal. La relation entre les activités en désoxygénation et en HDO et l'énergie de liaison métal-soufre (E(MS)) calculée ab initio des solides suit une courbe en volcan. Le sulfure mixte NiMoS (0.43), qui présente une E(MS) intermédiaire (127 kJ.mol-1), est le SMT le plus actif pour les deux réactions. Le catalyseur bimétallique CoMoS (0.1) présente la sélectivité HDO/DCO la plus élevée. À l'aide des résultats catalytiques et de calculs ab initio, deux mécanismes réactionnels sont proposés pour les voies de réactions HDO et DCO / By combining well defined experiments and density functional theory (DFT) calculations, we propose a rational understanding of the deoxygenation mechanisms of relevant oxygenate molecules (ethyl heptanoate and heptanal) so as to provide guides to define optimal catalytic systems for the hydrotreating of renewable feedstocks (vegetable oils, animals fats). The hydrotreatment of vegetable oils, with the deoxygenation reaction, is an alternative route to transesterification and can be used to obtain high quality diesel. The transformation of oxygenated model compounds was studied under a total pressure of 1.5 MPa, at 523 K, in a fixed bed reactor over various unsupported transition metal sulfide catalytic phases (TMS). Results have shown the influence of the sulfide phase on the selectivity for deoxygenation reaction (hydrodeoxygenation (HDO) and/or decarbonylation/ decarboxylation (DCO)) and the specific reactivity of the rhodium sulfide for the transformation of ethyl heptanoate. The study of the transformation of heptanal shows the reaction of deoxygenation is preferentially following the HDO pathway over all the catalysts. In our reaction conditions, heptanal was identified as a reaction intermediate of this deoxygenation pathway. The promoting effect of cobalt and nickel on the activity of monometallic molybdenum sulphide was observed for the transformation of heptanal. The relation between the deoxygenation and HDO rates and the ab initio calculated sulphur-metal bond energy E(MS) in the bulk TMS is following a volcano curve. Bimetallic sulfide NiMoS (0.43), with an intermediate E(MS) (127 kJ.mol-1), is found as the most active TMS for both reactions. The maximum of the HDO/DCO selectivity is obtained for the mixed catalyst CoMoS (0.1). Thanks to catalytic results and ab initio calculations, two reaction pathways are proposed for HDO and DCO reactions
|
Page generated in 0.0729 seconds