Thesis (PhD in Metallurgical Engineering)--University of South Australia, 1996

Thesis (Ph. D.)--University of Wisconsin--Madison, 1966. / Typescript. Vita. eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references.

Thesis (M.S.)--University of Wisconsin--Madison, 1965. / eContent provider-neutral record in process. Description based on print version record. Bibliography: 4 l. at end.

Thesis (Ph. D.)--McMaster University, 2003. / Advisor: Mohamed Elbestawi. Also available via World Wide Web.

Call number: LD2668 .T4 1965 M67 / Master of Science

A dissertation submitted to the Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, in fulfilment of the requirements for the degree of Masters of Science in Engineering. Johannesburg, 2017 / This dissertation presents the zinc recycling of tool grade cemented tungsten scrap material generated during commercial production at Pilot Tools Pty Ltd (South Africa), production of powders and alloys from the zinc recycled materials, and evaluation of the properties of the recycled and un-recycled powders and alloys. Tool grade cemented tungsten carbide inserts were subjected to the zinc recycled process under controlled conditions. Tungsten carbide, cubic (TiC, TaC, NbC, TiCN) carbides and Co were recovered from the recycled scrap material. Two recycled alloys, R and RA, and two un-recycled alloys NS and N were produced following the conventional powder metallurgy route. Alloy R was made from 100 % zinc recycled powder with stoichiometric adjustment of C only, and alloy RA was made from 100% zinc recycled powder with stoichiometric adjustment of C and Co. Alloy N was produced under the same conditions as the recycled alloys R and RA, while alloy NS was produced at commercial level at Pilot Tools Pty Ltd (South Africa) using un-recycled powders. The alloy properties were evaluated following standard procedures for hardmetals. When the zinc recycled material was mechanically disintegrated, about 70 % of the recycled material was recovered as fine powder, while 30% was recovered as coarse oversize particles. The oversize particles were quite tough due to a high Co content, and it was difficult to disintegrate them through milling or repeated zinc recycling. The recycled powders took twice as much time to mill to the desired size as the new un-recycled powders, and had predominantly angular particles, while the new powders had smaller more rounded particles. A cubic free layer (CFL) was formed in all the alloys during sintering, although the recycled alloys R and RA had a narrower CFL compared to the new alloys NS and N. The recycled alloys R and RA had carbide grain size, carbide contiguity, binder mean free path, hardness, fracture toughness and wear rate which were generally within the same ranges as the new un-recycled alloys. / MT2018

Improvement of manufacturing productivity is dependent on the successful automation of manufacturing processes, the success of which is based in turn upon the availability of information which describes the state of manufacturing operations. Acoustic Emission (AE) signals related to the cutting process and tool wear have been recently applied to monitor manufacturing processes, and various AE parameters can be used to provide process information. For example, when cutting tools become worn, AE energy generated at the interface of tool flank and work piece increases. This study is thus an experimental investigation of the AE spectrums representing AE signals energy distribution to determine the possibility of extracting useful parameters to provide on-line information about drilled-hole quality and drill-bit wear. An experiment conducted using a radial-arm drilling machine was employed to collect on-line AE drilling process spectrums, yielding eight indicator parameters. Drill wear states were measured using a machine vision system. Assessment of the drilled hole quality was based on tolerances established in Geometric Dimensioning and Tolerancing (GD&T). Correlations among drill wear, drilled-hole quality measurements, and the AE spectrum indicator parameters were examined by regression analysis. A forward-stepwise variable selection procedure was used to select the best-fit regression model for each drilled hole quality measurement associated with the set of one AE parameter raised to different powers. According to quality measurements, drilled holes were categorized as either "acceptable" or "unacceptable" holes, using cluster analysis with a group-averaging method. The usage of AE parameters to decide to which group a drilled hole belonged was also examined. From the experimental evidence, it was observed that there are strong relationships between AE parameters and drill-wear state and the quality measurements of drilled holes. AE parameters could be useful predictor variables to provide information to controller/operators to evaluate current drilling processes. Based on the status information of drill wear and the quality measurements, drilling processes can be adjusted accordingly. / Graduation date: 1997

Thesis--Auburn University, 2009. / Abstract. Includes bibliographic references (p.83-85).

published_or_final_version / Industrial Engineering / Doctoral / Doctor of Philosophy

Thesis (Ph. D.)--Rutgers University, 2007. / "Graduate Program in Industrial and Systems Engineering." Includes bibliographical references (p. 226-236).